Subscribe to Our Youtube Channel
Related Manuals for Totalcomp SW-50W
Summary of Contents for Totalcomp SW-50W
-
Page 1: Table Of Contents
CONTENTS PRECAUTIONS PREFACE NAMES AND FUNCTIONS OPERATIONS 1. General Weighing 2. Weighing with Tare 3. How to Convert the Unit of Weight 4. How to Set Auto Power Off BATTERY SYSTEM ERROR MESSAGE SPECIFICATIONS... -
Page 2: Precautions
PRECAUTIONS Precautions when installing the scale. To ensure that you get the most from your scale, please follow these instruction. Warning Scale must be grounded to minimize Do not disassemble the scale. Do not overload beyond the maximum electricity static. This will minimize When any damage or defect occurs, weight limit. - Page 3 Make sure to plug your scale into the proper power outlet. For maximum performance, plug into a power outlet 30 minutes before the usage for warm up. Attention For consistent and accurate reading, Avoid sudden shock to the scale. Grab on the bottom of the scale when maintain periodical check by your Internal mechanism could be damaged.
-
Page 4: Preface
PREFACE Thank you for purchasing our CAS SW Series. This scale has been designed with CAS reliability, under rigid quality control and with outstanding performance. Your specialty departments can enjoy these high quality reliable CAS products. We believe that your needs will be satisfied and you will have excellent reliability. This manual will help you with proper operation and care of the SW Series. -
Page 5: Operations
FUNCTION KEYS FUNCTIONS ZERO Used to set the zero point. TARE Used to enter a tare weight and used to cancel a tare weight. UNIT Used to convert the unit of weight. Turn on and off the display. OPERATIONS Turn on the display by pressing ON/OFF key. Then the display will show all the segments and count up "0"... -
Page 6: Weighing With Tare
2. Weighing with Tare Tare is the weight of container being used for a commodity. The TARE key subtracts the weight of the container. ZERO TARE UNIT Place a container on Press the TARE key. Place a commodity in the the platter. -
Page 7: How To Set Auto Power Off
4. How to Set Auto Power Off Auto-Power off makes the battery's life longer. When you don't operate the scale, this function makes the power OFF automatically. Before setting the Auto Power Off, make sure that the power is OFF. ZERO TARE ZERO... -
Page 8: Error Message
ERROR MESSAGE ERROR REASONS SOLUTIONS Err 1 An error of the initial zero range Set the platter empty Refer to specifications An overload SPECIFICATIONS MODEL SW-2 SW-5 SW-10 SW-20 5 0.002lb 10 0.005lb 20 0.01lb 50 0.02 lb CAPACITY 2 0.001kg 5 0.002kg 10 0.005 kg 20 0.01kg 80 0.05oz... - Page 9 CAS (USA) Corporation 99 Murray Hill Parkway East Rutherford, NJ 07073 10/06/2008 SW1N-Series CALIBRATION MODE WEIGHT SETTINGS FOR SW1N OR Z SERIES 1. Make sure the scale is off. Remove the platter assembly (metal and/or plastic platform.) 2. On the right hand side you will find a hole and a screw at the bottom. This is the sealing screw. Remove the sealing screw and then turn the scale upside down to find the calibration screw and silver plate located on the right side of the bottom of the scale (if keyboard is facing you and you tilt the scale upwards by the front.)
- Page 10 be set to 0. be set to 0. W-dP W-dP 5LBS 10LBS 20LBS 10KG 50LBS 20KG 5LBS 0.002 0.001 10LBS 0.005 0.002 20LBS 0.01 10KG 0.005 50LBS 0.02 20KG 0.01 10. After the capacity is set press the “ZERO” key. The display will flash “ ld” and show the middle up/down weight to be used in calibrating the scale.
- Page 11 CAS (USA) Corporation 99 Murray Hill Parkway East Rutherford, NJ 07073 10/06/2008 SW1N-Series Page 1 SPAN CALIBRATION FOR SW1N-SERIES FULL CAPACITY CALIBRATION 1. Make sure the scale is off. Remove the platter assembly (metal and/or plastic platform.) 2. On the right hand side you will find a hole and a screw at the bottom. This is the sealing screw. Remove the sealing screw and then turn the scale upside down to find the calibration screw and silver plate located on the right side of the bottom of the scale (if keyboard is facing you and you tilt the scale upwards by the front.)
- Page 12 2. The display will show “Per 10”. The “UNIT” key will increment the flashing digit and the “TARE” key will select which digit is flashing. When the per cent is set press the “ZERO” key. 3. The display will show “2ErO”. With the platter on the scale and nothing on the platter press the “ZERO”...
Need help?
Do you have a question about the SW-50W and is the answer not in the manual?
Questions and answers