Advertisement
Quick Links
SPECIFICATIONS
Type
Speaker unit
Full range
Input power (IEC)
Output sound pressure
level
Frequency range
Dimensions (W x H x D)
Mass
*Rating with low-cut filter equipped amplifier
Notes :
1. Specifications are subject to change without notice. / Mass and
dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum
analyzer.
System : SC-HT60EE-S Music Center System : SA-HT60EE-
1 way, 2 speaker system (Bass-ref.)
Impedance 6
6.5 cm Cone type x 2
220 W (Max)
85 dB/W (1.0 m)
95 Hz - 40 kHz (-16 dB)
110 Hz - 36 kHz (-10 dB)
270 mm x 92 mm x 95.4 mm
Front Speaker : SB-FS61GN-S
Surround Speaker : SB-FS62GN-S
Center Speaker : SB-PC41GN-S
Subwoofer : SB-W40P-S
ORDER NO. MD0603106C3
Specification
System : SC-HT60GN-
S
1.2 kg
S
SB-FSC61GN-S consists of SB-FS61GN-S(X2), SB-FS62GN-
S(X2) & SB-PC41GN-S(X1)
1
Speaker System
SB-PC41GN
Colour
(S)... Silver Type
Music Center System : SA-HT60GN-
Front Speaker : SB-FS61GN-S
Surround Speaker : SB-FS62GN-S
Center Speaker : SB-PC41GN-S
Subwoofer : SB-W40P-S
S
Advertisement
Related Manuals for Matsushita Electric SB-PC41
Summary of Contents for Matsushita Electric SB-PC41
- Page 1 ORDER NO. MD0603106C3 Speaker System SB-PC41GN Colour (S)... Silver Type SPECIFICATIONS Specification Type 1 way, 2 speaker system (Bass-ref.) Speaker unit Impedance 6 Full range 6.5 cm Cone type x 2 Input power (IEC) 220 W (Max) Output sound pressure 85 dB/W (1.0 m) Music Center System : SA-HT60GN- System : SC-HT60GN-...
-
Page 2: Assembling And Disassembling
2006 Matsushita Electric Industrial Co. Ltd.. All rights reserved. Unauthorized copying and distribution is a violation of law. 1. Assembling and Disassembling “ATTENTION SERVICER” Some chassis components may have sharp edges. Be careful when disassembling and servicing. 1. This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components. - Page 3 The following chart is the procedure for disassembling the casing and inside parts for internal inspection when carrying out the servicing. To assemble the unit, reverse the steps shown in the chart as below. 1.2. Disassembly of Front panel Step 1: Remove 6 screws from the rear cabinet assembly.
- Page 4 Step 2: Insert an allen key into the top hole of the rear cabinet assembly and push the front panel assembly as arrow shown. Step 3: Detach front panel unit. 1.3. Disassembly of Woofer 1 Follow (step 1) to (step 3) in Item 1.2. Step 1: Detach the (+) black and (-) gray wires.
- Page 5 Step 2: Remove 4 screws. 1.4. Disassembly of Woofer 2 Follow (step 1) to (step 3) in Item 1.2. Step 1: Detach the (+) red and (-) blue wires.
- Page 6 Step 2: Remove 4 screws. 1.5. Disassembly of Rear cabinet assembly Follow (step 1) to (step 3) in Item 1.2. Step 1: Detach the (+) red and (-) gray wires. Step 2: Remove the rear cabinet assembly. - Disassembly of terminal jack.
-
Page 7: Connection Of The Speaker Cables
Step 3: Remove 1 screw. Step 4: Remove the terminal jack. 2. Connection of the Speaker Cables - Be sure to connect speaker cables before connecting the AC power supply cord. - The load impedance of any speaker used with this unit must be 6 - Be sure to connect the cable from the right speaker to the right terminal and the cable from the left speaker to the left terminal. - Page 8 Notes : - To prevent damage to circuitry, never short-circuit positive (+) and negative (-) speaker wires. - Be sure to connect only positive (white) wires to positive (+) terminals and negative (blue) wires to negative (-) terminals. Incorrect connection can damage the speakers.
- Page 9 Positioning the speakers How you set up your speakers can affect the bass and the sound field. Note the following points: - Place the speakers on flat secure bases. - Placing speakers too close to floors, walls, and corners can result in excessive bass.
-
Page 10: Exploded View
The television’s demagnetising function should correct the problem. If it persists, move the speakers further away from the television. 3. Connection of Wiring Diagram 4. Exploded view 4.1. Cabinet Parts Location... - Page 11 4.2. Packaging Note: The diagram below shows the packaging for SB-PC41GN-S.
-
Page 12: Replacement Parts List
5. Replacement Parts List Notes : - Important safety notice : When replacing any of these components, be sure to use only manufacturer’s specified parts shown in the parts list. - [M] markings in the Remarks columns indicates parts supplied by PAVCSG. - Page 13 Ref. No. Part No. Part Name & Description Remarks CABINET AND CHASSIS RYPX0124-H FRONT PANEL ASS’Y RKKX0319-S REAR CABINET ASS’Y K4BC02B00017 TERMINAL JACK XTB3+10GFJ SCREW REEX0573 TRANSIT WIRE RGNV0202-S SPEC LABEL RKA0072-KJ LEG CUSHION CAPACITORS ECA1HAY5R6S 5.6uf 50V PACKING MATERIALS RPNV0111 POLYFOAM RPFX0110...