A/C Head Phase(X-Value); Electrical Adjustment; Servo Circuit; Switching Point - JVC HR-S2901U Service Manual

Hide thumbs Also See for HR-S2901U:
Table of Contents

Advertisement

3.2.4 A/C head phase (X-value)
Signal
(A1)
Alignment tape(SP, stairstep, NTSC) [MHP]
(A2)
Alignment tape(EP, stairstep, NTSC) [MHP-L]
Mode
(B)
PB
Equipment
(C)
Oscilloscope
Measuring point (D)
TP106 (PB. FM)
External trigger
(E)
TP111 (D.FF)
Adjustment part
(F)
A/C head base [Mechanism assembly]
Specified value
(G)
Maximum V.PB FM waveform
Adjustment tool
(H)
Roller driver [PTU94002]
(1) Play back the alignment tape (A1).
(2) Apply the external trigger signal to D.FF (E), to observe
the V.PB FM waveform at the measuring point (D).
(3) Set the VCR to the manual tracking mode.
(4) Loosen the screws (4) and (5), then set the Roller driver
to the innermost projected part of the A/C head. (See Fig.
3-2-4a.)
(5) Rotate the roller driver so that the A/C head comes clos-
est to the capstan. From there, move the A/C head back
gradually toward the drum until the point where the FM
waveform is maximized for the second time, and then
tighten the screws (4) and (5) temporarily.
(6) Play an alignment tape (A2) and set to the manual-track-
ing mode.
(7) Fine-adjust A/C head base position to maximize the FM
waveform, and then tighten the screws (4) and (5) firmly.
(8) Play alignment tapes (A1) and (A2) and confirm that the
FM waveforms are maximized when the tracking is at the
center position.
Roller driver
To the drum
Toward the capstan
Screw (4)
Head base
Toward the drum
A/C head
Screw (5)
To the capstan
Fig. 3-2-4a
Alignment tape
[SP, stairstep]
played with the
SP head
Drum side
Control head position
Fig. 3-2-4b
3-4
Alignment tape
[EP(LP), stairstep]
played with the
EP(LP) head
X-value adjustment point
Capstan side
Maximum
3.3

Electrical adjustment

Note:
The following adjustment procedures are not only necessary
after replacement of consumable mechanical parts or board
assemblies, but are also provided as references to be re-
ferred to when servicing the electrical circuitry.
In case of trouble with the electrical circuitry, always begin a
service by identifying the defective points by using the meas-
uring instruments as described in the following electrical ad-
justment procedures. After this, proceed to the repair, re-
placement and/or adjustment. If the required measuring in-
struments are not available in the field, do not change the
adjustment parts (variable resistor, etc.) carelessly.
3.3.1

Servo circuit

3.3.1.1

Switching point

Signal
(A1)
• Stairstep signal
(A2)
• Alignment tape (EP,stairstep,NTSC) [MHP-L]
Mode
(B)
• PB
Equipment
(C)
• Oscilloscope
Measuring point (D1)
• VIDEO OUT terminal (75Ø terminated)
(D2)
• TP106 (PB. FM)
External trigger
(E)
• TP111 (D.FF)
Adjustment part
(F)
• Jig RCU: Code "5A"
Specified value
(G)
• 7.5 ± 0.5H
Adjustment tool
(H)
• Jig RCU [PTU94023B]
(1) Play back the signal (A1) of the alignment tape (A2).
(2) Apply the external trigger signal to D.FF (E) to observe
the VIDEO OUT waveform and V.PB FM waveform at the
measuring points (D1) and (D2).
(3) Set the VCR to the manual tracking mode.
(4) Adjust tracking so that the V.PB FM waveform becomes
maximum.
(5) Set the VCR to the Auto adjust mode by transmitting the
code (F) from the Jig RCU. When the VCR enters the
stop mode, the adjustment is completed.
(6) If the VCR enters the eject mode, repeat steps (1) to (5)
again.
(7) Play back the alignment tape (A2) again, confirm that the
switching point is the specified value (G).
Trigger point
Switching point
Fig. 3-3-1-1a

3.3.1.2 Slow tracking preset

Signal
(A1)
• Ext. input
(A2)
• Color (colour) bar signal [NTSC]
Mode
(B1)
• S-VHS SP
(B2)
• S-VHS EP
Measuring point (D)
• TV-Monitor
Adjustment part
(F)
• Jig RCU: Code "71" or "72"
Specified value
(G)
• minimum noise
Adjustment tool
(H)
• Jig RCU [PTU94023B]
V.sync
V. rate
Switching point

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Hr-s2911uHr-s2911ucHr-s3901uHr-s3911uHr-s3911uc

Table of Contents