Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for GGMgastro ETHA1711
Summary of Contents for GGMgastro ETHA1711
- Page 1 Please read carefully before use Instructions for Ice Cream Display Freezer 1 / 12...
- Page 2 In order to better use our products and extend the service life of the products, please read this "INSTRUCTIONS" carefully before use. Product Specifications and Parameters 1.MILAN Series（MILAN） Dimensions (L*W*H) Cabinet Input power Model Power V/ph/Hz temperature ℃ ETHA1711 1728*1125*1350 1460 ETHA1710 1728*1092*1300 1460 -16℃~-18℃ 220~240/1/50 SPEWRHA12 2146*1011*2435...
- Page 3 Handling and placement 1. During the handling process, the inclination angle of the tank should not be greater than 45 degrees to avoid unnecessary damage; 2. This product should be placed in a ventilated and dry place, the ambient temperature of the working condition should be less than 32 ℃ (≤ 32℃), and the ambient humidity should be less than 60% (≤...
- Page 4 Power Requirements 1. This rated voltage of the product is 230V, and the voltage fluctuation must comply with the national regulations, that is, the fluctuation range should be within 10%; 2. The socket that supplies power to this product must be a two-hole or European standard socket with independent lines .
- Page 5 cleaning of the scattered food in the cabinet. 3. The ice cream shape should not extend to the position of the air outlet in the cabinet, so as not to cause the ice cream to melt (as shown in the figure below). Daily Use Precautions After the store is closed at night, take out the ice cream and store it in the chest freezer.
- Page 6 be performed at any time. Dust removal method: (1) Unplug the power plug. (2) Remove the rear grille. (3) Pull out the filter screen from the condenser, rinse the filter screen with clean water or tap lightly in an open and ventilated place to knock off the dust.
- Page 7 if there is too much water during the cleaning process, water will overflow from the water receiving box, resulting in a short circuit when the machine is turned on! ! ! If the operation is not carried out in accordance with the requirements of the INSTRUCTION manual, the user shall be responsible for the loss.
- Page 8 Indicator Symbol Status Meaning light Parameter setting Setting Status of temperature measuring and controlling Refrigeration work Refrigeration Refrigeration stop FLASH Refrigeration time delay Defrost Defrost work Defrost stop Fan work Fan stop Defrost dripping drip Start defrost dripping Stop defrost dripping Door switch Cabinet door open Cabinet door close...
- Page 9 Adjust menu and parameters Press the response Download the copy card pressing the keys for 3s View evaporator sensor temperature Press the response Exit from parameter setting； Press the response Press 3s to forced switch between pressing the keys for 3s refrigeration, defrost/defrost delay,...
- Page 10 setting of the current menu item, press the key of to adjust the parameter value, and then press the key of Set to return to the menu selection. In any parameter setting state, pressing the key of for 30 seconds or no key operation for 30 seconds will exit the parameter setting state while automatically saving the current parameter value.
- Page 11 4) Temperature controller alarm output Alarming code Alarming reason Display freezer cabinet temperature sensor failure Evaporator sensor failure Condenser sensor failure Condenser high temperature alarm Display freezer cabinet temperature high temperature alarm Cabinet temperature low temperature alarm Copy card programming failed The data in the copy card is inconsistent with the controller model, leading to programming failure...
- Page 12 Faults Phenomenon Causes Troubleshooting Compressor compressor The compressor Switch off and internal shuts down, temperature cut off the power thermostat rises to a high to cool the action temperature compressor, and (this phenomenon the compressor may only occur will reset when the ambient automatically temperature is...
Need help?
Do you have a question about the ETHA1711 and is the answer not in the manual?
Questions and answers