Sanus ELM809 Installation

In-Wall Power for SoundBar
Kit Includes:
Slim-line In-Wall Power Outlet and Cable Pass Panel Pre-wired PowerConnectors.
1' outlet connection / 6' inlet connection. Cutout template.
PowerOUT Panel
!
THIS PRODUCT IS NOT TO BE INSTALLED, DIRECT WIRED, OR BRANCHED TO THE BUILDING ELECTRICAL CIRCUIT/WIRING SYSTEM !
DO NOT MODIFY OR ALTER ANY PORTION OF THE COMPONENTS OF THE FACTORY ASSEMBLED APPLIANCE
Do not install this product near water, example, near a sink, tub, shower, swimming pool or laundry area.
Manufacturer is not liable for damages due to improper installation methods not followed herein.
This product does not have built-in electronic circuitry for surge protection or A/C filtering.
It is recommended that this product be connected to a quality surge-protector/power conditioner for equipment protection.
Disclaimer. Milestone AV Technologies, it's agents, suppliers, and affiliates, shall not be liable for any damages, not limited to; misuse, acts of nature,
verbal and written expression and improper installation. Improper installation is determined such to include, not limited to, non-code compliant installation, product
modifications, alterations, adjustments, and substitutions of components or materials.
Limited 2-year Warranty from Manufactures Defects: This product has a Limited Two Year product warranty against manufacturer's defects.
If you have any questions or experience any problems with this product, please contact Customer Service.
Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein
covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without
notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
©2014 Milestone AV Technologies. All rights reserved. Sanus is a division of Milestone.
All other brand names or marks are used for identification purposes and are trademarks of their respective owners.
SANUS • 6436 City West Parkway • Eden Prairie, MN 55344 USA
Customer Service: 800-359-5520 • 952-225-6013 • info@sanus.com • sanus.com
!
Step 1
Location - Wall Cutout
Determine SoundBar wall mount location.
Align between wall framing studs.
Use stud finder to determine in-wall obstructions between
framing both VERTICALLY and HORIZONTALLY.
Install horizontal below, TV PowerOUT and wall bracket.
Align with upper TV PowerOUT within same stud-bay
no more than 60" apart.
Install no more than 60" apart from the lower PowerIN,
unless you install optional PowerConnector Extension part CKRE
Use supplied template sheet to mark area to cut out from drywall.
Use a level to maintain proper alignment.
Carefully use drywall saw to cut along outside of line.
LEVEL
Wall Cut-out Template:
Lay against wall, use a level on edge of pape
Use a pencil to trace around edge.
Use drywall saw or sharp utility knife cut on t
This product, ELM809, requires installation with Sanus In-Wall Power Kits only.
Install only with models- ELM806, ELM807, and ELM808.
SoundBar Connector Kit

Power Extension Cable Management

Tools for Installation

Not Included
Stud Finder Level
PowerOUT
SoundBar
Do not exceed more
than 60" apart
PowerIN
If insulation exists, remove or push
completely away from the openings
to allow flush mounting properly.
Model ELM809
Drywall Saw Flat-Blade
Part No. 2013 All Rights Reserved
!
Only attempt installation within
2x2 or 2x4 wood/metal stud
framed wall.
Extend distance between
SoundBar and PowerIN
use optional part ELM810
PowerConnect Extension
!
|