Subscribe to Our Youtube Channel
Related Manuals for Renkforce RF-TTLP4-01
Summary of Contents for Renkforce RF-TTLP4-01
- Page 1 Operating Instructions Thermal Transfer Label Printer Item No.: 2734626 (RF-TTLP4-01 / HT300)
-
Page 2: Table Of Contents
Contents Contents ..........................2 Introduction ........................4 Intended use ........................4 Delivery contents ......................4 Latest product information ..................4 Developer documentation .................... 4 Spare parts ........................5 6.1. Thermal paper and thermal labels ................5 Description of symbols ....................5 Safety instructions ....................... - Page 3 14. Printing ........................18 14.1.1. Printing a blank label ..................18 14.1.2. Printing a self-test page ................... 18 14.1.3. Pausing and restarting print jobs ..............18 15. Interfaces ........................19 15.1. USB Interface ......................19 15.2. Serial port ......................... 19 15.3.
-
Page 4: Introduction
1. Introduction Dear customer, Thank you for purchasing this product. If there are any technical questions, please contact: www.conrad.com/contact 2. Intended use The product is a thermal transfer label printer. The product is intended for indoor use only. Do not use it outdoors. Contact with moisture must be avoided under all circumstances. -
Page 5: Spare Parts
6. Spare parts 6.1. Thermal paper and thermal labels The printer can print on any commercially available thermal paper and thermal labels. 7. Description of symbols The following symbols are on the product/appliance or are used in the text: Read the operating instructions carefully. The symbol warns of hazards that can lead to personal injury. -
Page 6: Safety Instructions
8. Safety instructions Read the assembly instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee. -
Page 7: Connected Devices
operation can no longer be guaranteed if the product: is visibly damaged, > is no longer working properly, > has been stored for extended periods in poor ambient conditions or > has been subjected to any serious transport-related stresses. > 8.5. -
Page 8: Product Overview
9. Product overview 9.1. Components... -
Page 9: Indicators
9.2. Indicators READY STATUS Indicator Status Color Action Color Action Green Solid on Ready Green Slow flash Dump mode Solid on Overheat of printhead Slow flash Ribbon out Solid on Head up Slow flash Out of paper Quick flash Abnormal label calibration Orange Solid on Out of ready... -
Page 10: Specification
10. Specification Items Parameter Type HT300 Printing Printing method Thermal transfer/ Direct thermal Resolution 203 dpi (8 dots/mm) Printing speed Max. 127 mm/s Printing width Max. 108 mm Printing length 15 - 1200 mm Processor NUC976 Memory 32 MB Flash 16 MB Detection Sensors... - Page 11 Items Parameter 90°, 180°, 270° rotatable, single characters 90°, Bitmap fonts Download Fonts 180°, 270° rotatable 16x16, 24x24. Traditional Chinese, Asian fonts Simplified Chinese, Japanese , Korean DOS437,720,737,755,775,850,852,855,856,857,85 Code pages 8,8 60,862,863,864,865,866, Windows 1250, 1251, 1252, 1253, 1254, 1255, 1256, 1257, 1258 ISO8859-1,-2,-3,-4,-5,-6,-8,-9,-15 DBCS 932 (JIS), 936(GBK), 949 (Koran), 950(BIG5) Code 39, Code 93, Code 128UCC, Code 128...
-
Page 12: Setting Up
11. Setting up 11.1. Connect peripherals The printer has the following peripheral ports: USB-B port RS-232C serial port RJ45 Ethernet port To make connections: 1. Move the power switch at the rear to position 0. 2. Connect the communication cable to the respective peripheral port. 11.2. -
Page 13: Installing Paper And Configuring Paper Type
13. Installing paper and configuring paper type Perform the following steps to install the paper and configure the printer for the installed paper/label type: 1. Install the paper roll. For large paper rolls, follow the instructions for external paper roll installation. - Page 14 Step 3 Step 4 Install the paper roll. Guide the label paper and set the label guides. 1. Lift out the spindle. 1. Release and lift the printing head. 2. Adjust the label supply plates on the 2. Below the printing head, pass the labels spindle until the CORE size printed on through the label guides.
-
Page 15: Loading Paper Rolls Externally
Step 7 Step 8 Link the ribbon to the rewind spindle. Lock the printing mechanism. 1. Lift the sticky end of the ribbon and pull 1. Push down the printing head until it the ribbon out just enough to reach the locks. -
Page 16: Aligning Label Sensor With Paper/Label Type
13.2. Aligning label sensor with paper/label type The label sensor detects the paper type that is installed. Align the sensor with the paper type you are using. 13.2.1. Aligning for continuous paper For continuous paper (Fig. 1), align the sensor with the left of the photoelectric hole (Fig. Fig. -
Page 17: Aligning For Punched Hole Label
13.2.3. Aligning for punched hole label For punched hole labels (Fig. 6), align the sensor with the right of the photoelectric hole (Fig. 7). Fig. 6 Fig. 7 Next step: Calibrate the printer for the paper/label type. 13.2.4. Aligning for blackmark paper For blackmark paper (Fig. -
Page 18: Calibrating The Printer For Paper/Label Types
13.3. Calibrating the printer for paper/label types Calibrate the printer to adjust the printing components to the label/paper type you have installed. Calibrate the printer via the Windows® Label Printer Utility software. When to calibrate: Calibrate if one of the conditions applies: Before printing for the first time ... -
Page 19: Interfaces
15. Interfaces 15.1. USB Interface SIGNAL NAME VBUS 15.2. Serial port SIGNAL NAME +5VDC 15.3. Ethernet Port SIGNAL NAME... -
Page 20: Configuring Printer With Windows® Label Printer Utility Software
16. Configuring printer with Windows® Label Printer Utility Software With the Windows® “Label Printer Utility” you can configure parameters of new and existing printers. 16.1. Getting started 1. Download the application HPRTUtilityForLabel from www.conrad.com/downloads your computer. 2. Open the application HPRTUtilityForLabel. -
Page 21: Adding New Printers
16.2. Adding new printers 1. Connect the printer to the computer/POS system. 2. Switch the printer on. 3. Open the application HPRTUtilityForLabel. 4. Click Add Printer. 5. Select the printer model and connection type. 6. Click Connect Test to test the printer connection. ... -
Page 22: Calibrating Printer For Label/Paper Type
16.4. Calibrating printer for label/paper type Prerequisites: > Printer is connected to computer/POS system. 1. Open the application HPRTUtilityForLabel. 2. On the main page, select the printer you want to configure from the printer list. 3. Click Label Auto Learn (or Label Auto Calibration) to calibrate the printer to paper/label type that is installed. -
Page 23: Cleaning And Care
18. Cleaning and care Adhesives and coatings of the media can transfer onto the printer parts, which can lead to accumulation of dust and debris. Regular cleaning helps to maintain print quality and prevents breakdowns. 18.1. Cleaning housing Important: Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions. ... -
Page 24: Cleaning Roller And/Or Paper Path
18.4. Cleaning roller and/or paper path Clean the roller and paper path if you notice reduced print quality or problems with paper detection. 1. Disconnect the printer from the power supply. 2. Open the printer cover. 3. Remove the installed paper roll. 4. - Page 25 This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in- cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represents the technical status at the time of printing.
Need help?
Do you have a question about the RF-TTLP4-01 and is the answer not in the manual?
Questions and answers