Quoizel TRE8409K Assembly Instruction Sheet

Please go to www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (1) A21 Medium Base bulb 150W Maximum.
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Fixture can only be mounted in the direction indicated on page 2.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Crossbar Assembly
A
x 1
Alternate
B Mounting screw
x 2
Fixture Body
C
x 1
-
STEP 1 Attach the Glass Panels and
Curve Panels to Fixture Body
A. Insert one Curve Panel (D) into the cage
of the Fixture Body (C). Attach the bottom
edge of the Curve Panel (D) to slot on one
side of the cage. And fold the Tabs in the
top edge of the cage to secure the top
edge of the Curve Panel (D). Repeat the
same process to install another Curve
Panel (D) to another side of the cage.
B. Insert one Glass Panel (E) into the cage
of the Fixture Body (C). Attach the bottom
edge of the Glass Panel (E) to slot in the
front of the cage. And fold the Tabs in the
top edge of the cage to secure the top
edge of the Glass Panel (E). Repeat the
same process to install another Glass
Panel (E) to the back of the cage.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
2016 QuoizelInc.
Assembly Instruction Sheet #IS-TRE8409K
for product cleaning tips. Go to the
20-30 minutes
Curve Panel
D
x 2
Glass Panel
E
x 2
Glass
F Shade
x 1
Steel
G Collar
x 1
Socket
I
H Collar
x 1
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
For Style TRE8409K
Care + Maintenance selection.
-
STEP 2 Install Glass Shade
A. Place the Glass Shade (F) and the Steel
Collar (G) over the socket as shown. By
using the Socket Collar Tool (I), thread the
Socket Collar (H) onto the socket and
hand tighten until snug to secure the
Glass Shade (F).
-
STEP 3 Installing the Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug
Socket
Note: Use the Alternate Shorter Mounting Screw (B) if your
Collar Tool
installation requires a shorter mounting screw.
x 1
Outlet
Box
Figure 1
Mounting Screw
C
or Alternate Short
Mounting Screw
Tab
-
STEP 4 Test Fit the Backplate to the Crossbar Assembly
Slot
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the backplate and Fixture Body (C) onto the Crossbar Assembly (A)
and secure with mounting balls. Note: The backplate and Fixture
Body (C) should be snug against the wall and held tight with the
mounting balls. If it is not, adjust the length of the mounting screw or
E
alternate short mounting screw on the Crossbar Assembly (A) by
unscrewing the preassembled hex nut and lock washer and then
D
screwing the mounting screws or alternate short mounting screws in
or out of the crossbar until the correct length is achieved. Once the
backplate and Fixture Body (C) is secure, remove the mounting
1of2
H
Figure 2
Outlet Box Screws
(not included)
A
Supply Wires
with Ground Wire
Figure 3
ReleasedDate:2016-11-08
Socket
F
G
I
.