Page 2
Thank you for purchasing the DSW-100 series simple weighing scale from SHANGHAI DIGITAL BALANCE ELECTRONIC CO., LTD. The DSW-100 series has many features and designed functions that are conducive to operate and increase customer satisfaction. We believe that all your needs will be fully match.
OPERATIONAL WARNING Contents Please follow the instructions below to operate the Operational Warning..................I product to ensure product and personal safety. Precautions....................II Before installation, 1. Conventional.................... 1 it is important to c h e c k w h e t h e r 1.1 Product Specifications ...................
1. CONVENTIONAL PRECAUTIONS Product specifications Please follow the prompts to extend the life. Maximum range 3 kg 6 kg 15kg 30kg 30lb Please avoid placing the product in the following locations: 60lb 3/6kg 6/15kg 15/30lb 30/60lb If the temperature is too high or too low, direct sunlight, wet place; At the shared power supply, excessive vibration, dust, and moisture.
1. CONVENTIONAL 1. CONVENTIONAL Indicator display Global view T h e u n i t o f w e i g h t i s “ g ” Front view Back view (gram)/ “ kg” (kg)/ “ lb” (pound)/ “ oz” (ounce)/when in counting mode, the corresponding “g”...
1. CONVENTIONAL 2. BASIC OPERATION Boot operation Interface ·Toggle the reset switch on the bottom left side of the scale USB socket RS232 Display Main/sub screen Note: 1. During the field check, press the [REZERO] key to exit the field check and enter the weighing mode.
2. BASIC OPERATION 2. BASIC OPERATION Shutdown operation Zero operation Method one: click [ON/OFF] button to shut down Make sure that the scale is in a stable state and put a heavy object, the weight must be less than the set allowable zero setting range, such as 0.500kg Method 2: Turn off the reset switch Click [REZERO] and remove the heavy object, which shows...
2. BASIC OPERATION 2. BASIC OPERATION Tare operation Counting and weighing operation Make sure that the scale is in a stable state and put on heavy Method one Enter weighing mode by setting button objects. The weight must be less than the set allowable peeling range, such as 2.500kg (1) Ensure that the scale is in a stable state (2) Press and hold the [REZERO] button for a long time, and...
Page 9
2. BASIC OPERATION 2. BASIC OPERATION (6) Click the [ ↑ ] button to enter the counting operation, the default display is 10 pieces, you need to put 10 pieces of goods on the weighing pan to count (7) Click the [ON/OFF] button to check the total weight. If the number of pieces placed on the weighing pan exceeds 10 pieces, click the [ ↑...
2. BASIC OPERATION 2. BASIC OPERATION Weight unit switch Backlight brightness setting Make sure the scale is stable Make sure the scale is stable Press and hold the [ ← ] key for 5 seconds, knowing that "bL.S Put a heavy object on the weighing pan, such as 0.545kg 3"...
3. EDIT SETTINGS 3. EDIT SETTINGS Keyboard shortcuts Customer function entry Press and hold the [REZERO] button, and click the [ ← ] button three times to enter the spec setting Setting type Quick operation E n t e r u s e r f u n c t i o n UNIT UNIT UNIT...
3. EDIT SETTINGS 3. EDIT SETTINGS 4. RS232C interface data format, stop bit is 1 bit, data bit 7 or 8 bits are optional. (SPEC 01,02 = SELECT .) 5. After the USB port is connected, the machine will automatically detect the data input by the USB port.
Page 14
3. EDIT SETTINGS 3. EDIT SETTINGS SPEC NO.06 SPEC NO.09 【BIT 3】Dual rang weight check by 【BIT 3/BIT 2】Negative weight display 0:Only the net weight is dual range 1:Both are dual range display 10: There is no 00: When the net 01: When gross 1 1 : I n v a l i d l o a d w e i g h t...
4. CALIBRATION OPERATION 4. CALIBRATION OPERATION Full scale rate correction Click the switch below the scale body to open the calibration Click [ ← ] Shift, [ ↑ ] Increment, can be modified to the weight to be calibrated, such as 5kg Modify BIT 3 of SPEC 12 to "1"...
4. CALIBRATION OPERATION 4. CALIBRATION OPERATION Click[ ← ] Shift, [ ↑ ] Increment, modify to the calculated scale parameter Internal code check/display Modify BIT0 in SPEC 05 to "1" Remove the heavy object, and press [REZERO] to enter the zero confirmation and wait, click [REZERO] again to enter the zero confirmation Click [REZERO] button to save...
6. PROMPT MESSAGE 7. SERIAL AND USB Prompt information list POS serial protocol used in China Weight overload 7.1.1. RS232C Interface protocol: The baud rate is set by SPEC01, Gross or net weight is negative bit2~0 (1200~57600). The stop bit is 1 bit and the data bit is 8 bits. When the [REZERO] button is pressed 888888 7.1.2.
Page 20
7. SERIAL AND USB 7. SERIAL AND USB 3XH,3XH(LSB),0DH 7.1.5.2 Continuous data output, special format 2 (Special data BITS 5 type 2) =“1” SPEC SET: SPEC02 =11X1, SPEC 20= 0100, SPEC 21= XXXX BITS 6 =“1” DATA FORMAT. 3XH(MSB),3XH,3XH,3XH, 2EH("."),3XH,3XH(LSB), BITS 7 =“0”...
7. SERIAL AND USB 7. SERIAL AND USB x46,0x0d,0x0a Ex3. When NET WEIGHT is underload. (When the weight is less Standard POS serial port protocol than -2 divisions, and the negative weight mask function spec06. DSW-100 FOR POS/ECR INTERFACE & Protocol bit3,2=00,01 has been set) 7.2.1 POS/ECR Interface The data format is 0x30,0x20,0x20,0x20,0x20,0x20,0x55,0x...
Page 22
7. SERIAL AND USB 7. SERIAL AND USB 7.2.3 TYPE-0 INTERFACE 7.2.4 TYPE-2 INTERFACE Most P.O.S Systems, ECRs and some TEC P.O.S Systems. : Discontinual RS-232C Interface 1) PROTOCOL SHARP ER-AXXX, ER-A450T, New SANYO ECRs using RS- EXTERNAL DEVICE SCALE(DSW-100) 232,TOLEDO 3213 etc.
Page 23
7. SERIAL AND USB 7. SERIAL AND USB ii>Simplified Status Codes 7.2.5 TYPE-4 INTERFACE > NCI ECR(NCR2170), SAMSUNG ER-5100,ER-5115, CRS .etc 1) PROTOCOL STATUS POS/ECR SCALE (DSW-100) ASCII Character ASCII Character Definition <W> ------------> (ASCII Code) (ASCII Code) <CR> ------------> 0 (30H) 0 (30H) ========================================== Inquiry...
Page 24
7. SERIAL AND USB 7. SERIAL AND USB 7.2.7 TYPE-6 INTERFACE i>Status Bytes > SAMSUNG ECR (ER-670, ER-5100, SPS-520 ), Most P.O.S > 9600 baud rate Bit No > 8 Data bit Bit 7 Parity Bit Parity Bit > Non Parity Bit 6 >...
Page 25
7. SERIAL AND USB 7.2.8 TYPE-7 INTERFACE > DELTA cash register protocol Communication type (Only the original weight unit value output) FIX WORD NET WEIGHT TEXT (With decimal point) + RS_CR + RS_LF 1> PROTOCOL Cash Register Scales(DSW-100) -------------------------------------------------------------- D CR LF <--------------------------------------------------------------- S W W W .