Whirlpool WDF110PAB Quick Start Manual page 2

PRODUCT MODEL NUMBERS
WDF110PAB WDF331PAM
WDF111PAB WDF340PAM
WDF120PAF WDF520PAD
WDF121PAF WDF540PAD
WDF130PAH WDF545PAF
WDF131PAH WDT530HAM
WDF320PAD WDT540HAM
WDF330PAH WDT710PAH
WDF331PAH WDT720PAD
DRAIN REQUIREMENTS
A new drain hose is supplied with your dishwasher. If drain
■
hose is not long enough, use a new drain hose with a
maximum length of 12 ft (3.7 m) that meets all current AHAM/
IAPMO test standards, is resistant to heat and detergent, and
fits the 1" (25 mm) drain connector of the dishwasher. See
the "Tools and Parts" section at the front of the guide for part
details and orders.
Make sure to connect drain hose to waste tee or disposer
■
inlet above drain trap in house plumbing and 20" (508 mm)
minimum above the floor. It is recommended that the drain
hose either be looped up and securely fastened to the
underside of the counter or be connected to an air gap.
Make sure to use an air gap if the drain hose is connected to
■
house plumbing lower than 20" (508 mm) above subfloor or
floor.
Use of air gap
Air gap
If required, the air gap should be installed in accordance with
■
the air gap installation instructions. When you are connecting
the air gap, a rubber hose (not provided) will be needed to
connect to the waste tee or disposer inlet.
Use 1/2" (13 mm) minimum I.D. drain line fittings.
■
WATER SUPPLY REQUIREMENTS
This dishwasher has a water heating feature and also requires
■
a connection to a hot water supply line.
A hot water line with 20 psi to 120 psi (138 kPa to 862 kPa)
■
water pressure can be verified by a licensed plumber.
120°F (49°C) water at dishwasher.
■
Because Whirlpool Corporation policy includes a continuous commitment
to improve our products, we reserve the right to change materials and
specifications without notice.
W11542837A
Undercounter Dishwasher
3/8" (95 mm) O.D. copper tubing with compression fitting or
■
flexible braided water supply line. See the "Tools and Parts"
section at the front of the guide for part details and orders.
WDT730HAM
WDT730PAH
NOTE:
WDT735PAG
recommended.
WDT735PAH
WDP540HAM
A 90° elbow with 3/4" (95 mm) hose connection with rubber
■
WDP560HAM
washer. See the "Tools and Parts" section at the front of the
WDP730HAM
guide for part details and orders.
Do not solder within 6" (152 mm) of the water inlet valve.
■
If installed in new construction, make sure the house water
■
supply lines have been flushed prior to connecting the
dishwasher to remove any debris that may exist in the supply
line.
NOTE:
recommended to install a new water line (see the "Tools and
Parts" section at the front of the guide for part details) and
drain hose (supplied) with the new dishwasher.
ELECTRICAL REQUIREMENTS
You Must Have:
120 V, 60 Hz, AC only, 15 A or 20 A, fused electrical supply.
■
Copper wire only.
■
A maximum of 2 field wiring supply conductors (12 AWG
■
largest size) plus 1 grounding conductor are permitted in the
terminal box.
We Recommend:
A time-delay fuse or circuit breaker.
■
A separate circuit.
■
If Connecting Dishwasher with a Power Cord:
Use UL Listed power cord kit marked for use with
■
dishwasher. See the "Tools and Parts" section at the
front of the guide for part details and orders.
Plug into a grounded 3 prong outlet. Outlet must meet
■
all local codes and ordinances.
If Connecting Dishwasher with Direct Wiring:
Use flexible, armored, or nonmetallic sheathed
■
copper wire with grounding wire that meets the wiring
requirements for your home and local codes and ordinances.
Use a UL Listed/CSA Approved metallic strain relief.
■
Dimensions are for planning purposes only. For complete details, see
Installation Instructions packed with product. Specifications subject to
change without notice.
1/2" (13 mm) minimum plastic tubing is not
If replacing an existing dishwasher, it is
1