Related Manuals for Nordic Propeye OY1410
Summary of Contents for Nordic Propeye OY1410
- Page 1 OY1410 LoRaWAN® Pulse meter Product manual version 1.0 January 24, 2023 support@propeye.se Product manual, version 1.0, January 31, 2023, www.nordicpropeye.com...
-
Page 2: Table Of Contents
OY1410 LoRaWAN® Pulse meter Table of contents Disclaimer ........................3 Technical support ....................3 Warnings ........................4 Environmental ....................... 5 Product Description ...................... 6 Installation and activation ..................... 7 LoRaWAN Configuration ..................7 Physical activation ....................7 Mounting IWM-PL on to Water meter ..............8 IWM-PL configuration .................... -
Page 3: Disclaimer
Propeye makes no warranties based on the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Nordic Propeye reserves all rights to this document and the information contained herein. -
Page 4: Warnings
OY1410 LoRaWAN® Pulse meter 2 Warnings The following safety precautions must be observed during all phases of the operation, usage, service or repair of this Nordic Propeye product. • Read the product manual. • Do not modify the product. • The product should not be exposed to extreme heat or open flame. -
Page 5: Environmental
OY1410 LoRaWAN® Pulse meter 3 Environmental This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste by taking it to a collection point designated for the recycling of electrical and electronic appliances. -
Page 6: Product Description
OY1410 LoRaWAN® Pulse meter 4 Product Description The OY1410 Pulse meter is dedicated to be used together with B Meters’ IWM-PL3/IWM- PL4 sensors. The total setup consists of the OY1410 Pulse meter, IWM-PL unit as well as a water meter, on which the IWM-PL unit will be mounted. Product manual, version 1.0, January 31, 2023, www.nordicpropeye.com... -
Page 7: Installation And Activation
Configuration on the network server is done with the AppEUI. It is possible to order a batch of devices configured with a customer unique AppEUI from the Nordic Propeye OUI range. The device is configured with device unique DevEUI and AppKey. The device is default configured for OTA provisioning. -
Page 8: Mounting Iwm-Pl On To Water Meter
OY1410 LoRaWAN® Pulse meter White cable Yellow cable Ch2 0-10V Green cable Ch1 0-10V Brown cable Make sure that both jumpers are set to 0-10V as illustrated by the picture to the right. After that you install the (replaceable) batteries, which activates the unit, and you close the box. - Page 9 OY1410 LoRaWAN® Pulse meter The K-index and Pulse ratio X defines the number of liters per pulse. It is important that the Oy1410 is configured with the same setting. The table below shows the settings for different water meter models: Watermeter model K index Pulse Ratio X...
-
Page 10: Function Description
OY1410 LoRaWAN® Pulse meter 6 Function description The OY1410 counts the pulses output by the IWM-PL3 or IWM-PL4. The corresponding water volume depends on the set “Pulse ratio X”-value in the IWM-PL3 or IWM-PL4, which in turn depends on the type of water meter used. To get the OY1410 to report water volume in liter it is required to set the IWM Pulse Ratio to the same value as Pulse Ratio X in the IWM-PL3 or IWM-PL4. -
Page 11: Startup Sequence
OY1410 LoRaWAN® Pulse meter 7.2 Startup sequence When the device has joined the network, startup transmissions are performed in order to make it easier to configure the device using downlink commands. When the startup sequence is completed normal operation is started. There are at least five startup transmissions. -
Page 12: Commands
7.3 Commands Index Description Datatype Encoding Valid range Access Unsolicited Description Note 0x03 FW build hash 6 x Uint8 Query Unique number that identifies the firmware version 0x05 Device reset Action Reset of device 0x06 CPU voltage Uint8 25mV/ 0-3.6V Query Read CPU voltage. -
Page 13: Examples
OY1400 LoRaWAN® converter 0-10V, 4-20 mA 7.4 Examples Uplink: 012B0000123401 Current counter value is 1234HEX = 4660. Status bit 0 is set indicating a reset has been detected. • Setting the reporting interval to 1440 minutes = 24 hours. Downlink command: 012605A0 •...
Need help?
Do you have a question about the Propeye OY1410 and is the answer not in the manual?
Questions and answers