Advertisement
Quick Links
Advertisement
Related Manuals for Zicooler Suitable UML-046
Summary of Contents for Zicooler Suitable UML-046
- Page 1 Zicooler Bladeless Fan Instruction Manual Suitable UML-046...
- Page 2 TABLE OF CONTENTS Accessories --------------------------------------------- 2 Parameters ---------------------------------------------- 3 Remote Control Battery Installation and Operation --------------------------------------------------------- 4-5 Fan Operating Instructions--------------------------- 6 HEPA Filter Replacement --------------------------- 7 Malfunction Inspections and Contacts ------------8-9 Cleaning and Maintenance-------------------------- 10 Safety Precautions -------------------------------- 11-12 Accessories Instruction Manual Remote Control...
- Page 3 Basic Parameters Product name: Bladeless Fan UML-046 Model: Rated voltage: 110-120V Rated power: 20-45W Rated frequency: 50/60HZ Timing: 1-8H Swing angle: 80° Notice to Users Bladeless fan speed level and corresponding noise Speeds 1-3 30-40dB Speeds 4-5 40-45dB Speeds 6-8 45-60dB Attention: The above data are measured in a soundproof room, and the test error in the normal...
- Page 4 Remote Control Operation ON/OFF Swing Timing + Wind speed + Wind speed - Timing - Strong wind Sleep wind ① When the fan is in the standby state, press the ON/OFF button to start running; when the fan is in the running state, press the ON/OFF button to stop running and enter the standby state.
- Page 5 ④ Press the “wind speed +”button on the remote control to turn up the wind speed, and press the “wind speed -”button to turn down the wind speed. ⑤ Press the “Swing” button on the remote control to activate the swing mode. The swing angle is °.
- Page 6 Remote Control Battery Loading 1. Slide and remove the battery cover from the remote control. 2. Prepare a button cell, with the side with letters facing upwards, and load the button cell into the remote control. 3. Reinstall the battery cover to the remote control.
- Page 7 Fan Operating Instructions Buttons are as shown in the figure WL receiver ON/OFF Swing Screen Down ■ON/OFF Connect the plug to the socket, and press the power button, the power indicator will light up and the fan will enter the standby state, then press the ON/OFF button, the buzzer will prompt “beep”...
- Page 8 Instructions of HEPA Filter Replacement 1) Disconnect the power cord. 2) A lock and unlock icon is provided on the base of the bladeless fan, and the arrow on the base indicates the lock and unlock status of the base. 3) Hold the fan, and rotate it counterclockwise toward the unlock icon, and you will hear...
- Page 9 You can click “Problem with Order” under “Your Orders”, select “Other Issue”, click “Contact Seller” and select “Other Issue” to Contact our Amazon store directly Alternatively, you may click the store name on the right side of the product homepage to move to the new page, and then click "Ask a Question"...
- Page 10 Cleaning and Maintenance ■ Make sure to disconnect the plug and cut off the power supply before maintenance. During maintenance, do not sprinkle or splash water onto the smart air-purifying fan for cleaning, for water may enter and result in fan damage. Do not clean the smart air-purifying fan with lacquer thinner, gasoline, alcohol, bleacher or metal objects, for they may cause discoloration or...
- Page 11 Safety Precautions Warning The following requirements must be observed so as to avoid fire accident, electric shock, and personal injury For other requirements, please refer to the applicable national and local electrical regulations. ● Children, elderly or disabled persons as well as people who have never used the fan before should use the fan under supervision and guidance.
- Page 12 ● Do not run a fan with a carpet covering over, and do not cover the fan with a rag, other devices or similar materials. The power cord shall be arranged away from frequently accesses and place in an area seldom access area to prevent tripping hazards;...
Need help?
Do you have a question about the Suitable UML-046 and is the answer not in the manual?
Questions and answers