Advertisement
Colour Monitor
Quick Start Guide
USB Cable
HDMI Cable
Silicon Foot
Stand Bar
for US
for EU
for UK
Power Plug
DC Power Adapter
(Provided by regions)
* Di erences according to regions.
Display design and accessories may di er from those illustrated above.
Rear view
Speaker
Wall Mount
Reset Button
Menu
Screw Hole
Volume
Stand screw
hole
VESA mount
(Screw spec: M4)
Top view
Reserved Expansion Port
Micro USB
For SW upgrade only
Mounting
1
2
Use a screwdriver to loosen
Use a screwdriver to
the screw on the left side of
detach the back cover.
the back cover.
5
6
To mount the back cover to the wall, ip
Plug the power cable to the
over the back cover, the "PHILIPS" logo
"DC12V" port, then connect
should face the wall. Use a screwdriver to
the network cable to "LAN"
insert nails (x3) into the holes of back
port of the signboard.
cover, then x the back cover to the wall.
Installing the stand
* Simply screw the supplied table stand onto the stand screw hole.
Landscape
Portrait
CAUTION
Risk of explosion if the battery is replaced by an incorrect type
Wait one-half hour after switching o before handling parts
3
4
Remove the back cover
Stick the silicon gaskets
from the signboard.
(provided) on the back
cover .
7
* Mounting and installation
Mounting Option 1: [VESA mount]
Supporting VESA standard:
VESA MIS-D75 (75*75mm)
Supporting screw: M4*4mm
(exclude the mounting plate thickness)
Mounting Option 2: [Using back cover]
Supporting screw: Self-tapping screw *3pcs
Insert the signboard carefully
(exclude the mounting plate thickness)
into the back cover which is
* Installation height: <2 m
already mounted on the wall.
CARE AND WARNING
WARNING: Changes or modi cations to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the Radio Equipment
Directive (2014/53/EU). The following test methods have been applied in order to
prove presumption of conformity with the essential requirements of the Radio
Equipment Directive This equipment is compliant with Class A of EN55032. In a
residential environment this equipment may cause radio interference.
Correct Disposal of this product. This marking indicates that this product
should not be disposed with other household wastes throughout the EU. To
prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used device, please use the
return and collection systems or contact the retailer where the product was
purchased. They can take this product for environmental safe recycling.
"FCC & CE RF Radiation Exposure Statement Caution: To maintain compliance with
the FCC & CE's RF exposure guidelines, place the product at least 20cm from near by
persons. "
The suitable temperature for the Colour Monitor and sccessories is 0°C-45°C.
Adaptor with ferrite must be used with this equipment to ensure compliance with the
Class A FCC limits.
Power Adapter information:
Model No.: ADS-26SGP-12 12024E
INPUT: 100-240V~50/60Hz
OUTPUT: 12
2.0A
- Replacement of a battery with an incorrect type that can be defeat a safeguard;
- Disposal of a battery into re or a hot oven, or mechanically crushing or cutting of a
battery, that can result in an explosion;
- Leaving a battery in an extremely high temperature surrounding environment that
can result in an explosion or the leakage of ammable liquid or gas;
- A battery subjected to extremely low air pressure that may result in an explosion or
the leakage of ammable liquid or gas.
Advertisement
