Advertisement
Advertisement
Related Manuals for Soundstream Edge Series EGA2160
Summary of Contents for Soundstream Edge Series EGA2160
- Page 1 EDGE DIGITAL AMPLIFIER OWNER MANUAL...
-
Page 2: Table Of Contents
TABLE OF CONTENTS INTRODUCTION FEATURES & SPECIFICATIONS CONTROLS & FUNCTIONS EGA900D / 1400D / 1700D PLANNING & MOUNTING YOUR SYSTEM WIRING DIAGRAMS ADJUSTING & TUNING TROUBLE SHOOTING 4~10... -
Page 3: Introduction
INTRODUCTION Amplifier's provide high-performance sound reinforcement for you mobile audio equipment. The Multi-Mode bridging capabilities allow flexibility in hosting several different speaker configurations. To achieve optimum performance, it is highly recommended that you read this Owners Manual before beginning installation. -
Page 4: Features & Specifications
FEATURES TST ( Twin Stack Technology) 2 amplifier's to drive one voice coil effectively doubling the power. Class D circuitry High quality FR-4 circuit board Continuously variable low-pass filter (50Hz to 150Hz) Continuously variable subsonic filter (15Hz to 40Hz) Subwoofer equalizer control switch Phase inversion switch (0 -180 ) Platinum RCA input and output OEM floating ground input... -
Page 5: Controls & Functions 4~10
Controls & Functions EGA900D / 1400D / 1700D +12V EGA900D POWER SPEAKER +12V LINE OUT INPUTS CONNECTION REMOTE FUSES BRIDGED BASS PHASE L-CH R-CH L-CH R-CH POWER PASS BOOST SHIFT SONIC LEVEL MASTER SLAVE PROTECT... - Page 6 Controls & Functions 1.Speaker terminals 2. Input Sensitivity Adjustment This control adjusts the amplifier's input sensitivity. Input sensitivity is variable from 200 Millivolts to 8 volts. Clockwise increases sensitivity. Counterclockwise decreases sensitivity. The amplifier can be driven to full power with a wide range of signal levels. A lower signal level will require increased sensitivity for full power.
- Page 7 Controls & Functions 4. Low Level OUT RCA jacks The LINE OUT allows you to build multiple amplifier systems without having to use splitter cords to distribute the signal. Now it is simply a matter of bringing one set of RCAS into the first amplifier, then using the line out RCA jacks as the feed to the next amplifier.
- Page 8 Controls & Functions 7. B-Terminal (Chassis ground) +12V To avoid unwanted ignition noise caused by ground loops, it is essential that the Amplifier be grounded to a clean, bare, metal surface of the vehicles chassis. Note : GROUND WIRE SHOULD NOT BE EXTENDED MORE THAN 3 FT (1 METER). 8.
- Page 9 Controls & Functions To remote wire car stereo. This amplifier is turned "ON" remotely when vehicle's stereo is turned "ON" Note : IF YOUR RADIO DOES NOT HAVE +12 VOLT OUTPUT LEAD WHEN TURNED ON, THE "REMOTE" TERMINAL ON THE AMPLIFIER CAN BE CONNECTED TO VEHICLES ACCESSORY CIRCUIT WHICH PROVIDES +12V WHEN THE CAR IS ON.
- Page 10 Controls & Functions 13. Remote Control Input - Fig 1. Remote Boost Control : EGA-RM 14. LED indicator POWER : This GREEN LED will illuminate when the amplifier is turned "ON". If it fails to illuminate, check the power connections to the Amplifier and fuses. PROTECT: The amplifier protection circuitry will disable the amplifier if input overload, short circuit or extremely high temperature conditions are detected.
-
Page 11: Planning & Mounting Your System
Fig 1. LEVEL EGA-RM Remote Bass Boost Control : EGA-RM Remote Bass Boost Control : This control adjusts the Bass Boost gain for the amplifier's speaker output (0 - +12dB) Planning and Mounting Your System The mounting position of your Amplifier will have a great effect on its ability to dissipate the heat generated during normal operation. -
Page 12: Wiring Diagrams
EGA900D / 1400D / 1700D Bridging Two Amplifier's BRIDGED MODE MASTER AMP BRIDGED SWITCH : MASTER POSITION EGA900D FUSES SLAVE AMP BRIDGED SWITCH : SLAVE POSITION EGA900D FUSES SPEAKER SUB WOOFER 1 OHM POWER SPEAKER +12V POWER PROTECT POWER SPEAKER +12V POWER PROTECT... -
Page 13: Adjusting & Tuning
Tuning on the Amplifier The amplifier automatically turns on a few seconds after you turn your vehicle's ignition switch to ACC or ON or turn on your auto sound system, depending on how you wired the system. The POWER indicator on the top of the amplifier lights when the amplifier is on. Important : Your amplifier requires 30 amps or more of power from your vehicle's battery during operation. -
Page 14: Trouble Shooting
Trouble Shooting SYMPTOMS NO SOUND AMP NOT SWITCHING ON NO SOUND IN ONE CHANNEL AMP TURNING MEDIUM / HIGH VOLUME PROTECTION LAMP ON CHECK Is the power Check all fuses to amplifier. Be sure Turn-on lead is connected LED illuminated? check signal leads.