Table of Contents
Advertisement
2F200
Two Channel
High Power Car Audio
Amplifier
4F200
Four Channel
High Power Car Audio
Amplifier
Congratulations on your
purchase of a
Sound Storm Laboratories
FORCE Amplifier.
It has been designed, engineered
and manufactured to bring you
the highest level of performance
and quality, and will afford you
years of listening pleasure.
Thank you for making Sound
Storm Laboratories your choice
for car audio entertainment!
U S E R ' S M A N U A L
CONTENTS
page
2
Introduction
2
What is included?
3
Features
3
About 2 Ohm operation
4
General precautions
4
Installation precautions
5
Mounting the amplifier
6
Connecting the amplifier
7
Low level input wiring
8
High level input wiring
9
Power and Speaker wiring
10 Troubleshooting
11 Specifications
FORCE Amplifier User's Manual - page 1
Advertisement
Table of Contents
Related Manuals for Ssl Force 2F200
Summary of Contents for Ssl Force 2F200
- Page 1 4F200 Four Channel High Power Car Audio Amplifier Congratulations on your purchase of a Sound Storm Laboratories FORCE Amplifier. It has been designed, engineered and manufactured to bring you the highest level of performance and quality, and will afford you years of listening pleasure.
-
Page 2: Introduction
Introduction With the Sound Storm Laboratories FORCE high power amplifier series, we are introducing two new models, both designed in the USA. This new series includes a 2-channel and a 4-channel amplifier. These FORCE models feature a low pass crossover (one for each channel on the 4F400), and both high level and RCA low level inputs on the front panel. -
Page 3: Features
Features Your new FORCE amplifier features the following: • 2 Ohm stable stereo operation with output power increase • Thermal and speaker short protection • Soft turn-on circuit • Remote turn-on/turn-off circuit • Variable input gain control • Built-in fixed crossovers: 2F200: fixed (200Hz) 4F400: fixed low pass (120Hz) on CH3/4... -
Page 4: General Precautions
General precautions Before installing and using your new Sound Storm Laboratories amplifier, please become familiar with all the information contained in this manual. Please keep this manual in a safe place for future reference. • Do not open or attempt to repair this unit yourself. -
Page 5: Mounting The Amplifier
Mounting the amplifier 1. Find a suitable location in the vehicle in which to mount the amplifier. 2. Make sure there is sufficient air circulation around the intended mounting location. 3. Mark the location for the mounting hole screws by positioning the amplifier where you wish to install it. -
Page 6: Connecting The Amplifier
Connecting the amplifier Before doing any wiring, look through this manual and identify the diagrams to follow for power, input and speaker connections for your particular installation. Be sure you understand all the connections before you proceed. 1. Connect the power ground terminal to the closest point on the chassis of the car. -
Page 7: Low Level Input Wiring
Low Level Input Wiring Low-level (RCA) input wiring is preferred for best audio performance. Always use a high-quality RCA cable for best audio performance. NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time! 2-Channel Amplifier 2F200 Outputs of head... -
Page 8: High Level Input Wiring
High Level Input Wiring, cont. The high level input(s) should only be used when your head unit lacks RCA outputs. If the RCA outputs are not present, connect the speaker outputs from the receiver to the high level input connector of the amplifier. Be sure to observe polarity to avoid audio phase problems. -
Page 9: Power And Speaker Wiring
Power and Speaker Wiring SPEAKER IMPEDANCE 2-8 OHMS Channel Mode Chassis ground point to REMOTE TURN-ON terminal of head unit Battery FUSE SPEAKER IMPEDANCE 2-8 OHMS Chassis ground point to REMOTE TURN-ON terminal of head unit Battery FUSE RIGHT Speaker LEFT Speaker Speaker... -
Page 10: Troubleshooting
Troubleshooting If you experience operation or performance problems with this product, compare your installation with the electrical wiring diagram on the previous pages. If problems persist, read the following troubleshooting tips which may help eliminate the problems. SYMPTOM POSSIBLE REMEDY Amplifier will not Check to make sure you have a good ground connection. -
Page 11: Specifications
Specifications Two Channel Car Audio Amplifier MODEL 2F200 RMS POWER 50W x 2 into 4 Ohms MAX POWER 100W X 2 into 2 Ohms Min. speaker 2 Ohms impedance 0.01% Frequency response 12Hz-22kHz Signal-to-noise ratio 90dB Channel separation 60dB Crossover 120Hz fixed low pass high pass... - Page 12 Notes...
Need help?
Do you have a question about the Force 2F200 and is the answer not in the manual?
Questions and answers