Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for jcb PHBE
Summary of Contents for jcb PHBE
- Page 1 INSTRUCTION MANUAL PHBEK Preheater Set for PCBs up to 36x28cm/14x11”...
-
Page 2: Packing List
This manual corresponds to the following references: PHBE-9KB (100V) PHBE-1KB (120V) PHBE-2KB (230V) Packing List The following items are included: PHBE Preheater Unit ......1 unit PHBS Support ........ 1 unit Ref. PHB-SA Console ......1 unit RJ45 Cable ....1 unit Power Cord .....1 unit Ref. -
Page 3: Features And Connections
para manuales - color gris 200 mm Features and Connections 130 mm 130 mm Preheater Unit Heating Areas 100 mm Zone A Zone B Fuse 80 mm Fixing Brackets for PHBS Support Thermocouple Connectors x4 (Type K) 60 mm RJ12 Connector Main Switch to Robot RJ45 Connector... -
Page 4: Height Adjustment
Height Adjustment PHBS support allows adjustment for 3 heights between the PCB and the Heating Area of the Pre- heater Unit. To change the height, do as follows: To raise the support, hold the base and pull up. To lower the support, press the button and push down. - Page 5 para manuales - color gris 200 mm Fast PCB Replacement 130 mm 130 mm PHBS support lets replace PCBs of the same batch fast and easily. Use the sliding guides to change the PCBs. 100 mm Removing the PCB Placing another PCB Loosen one sliding guide (1), pull it back (2) Position the new PCB (4) and tighten the and lift out (3) the PCB.
- Page 6 º º º º Power C 100 P 100 P 100 º º º P 100 º Work Display The console offers an intuitive user interface, which provides quick access to station parameters. 14:15 Status Indicator Max. Rate 14:15 Status Bar º...
-
Page 7: Recommended Guidelines
para manuales - color gris 200 mm Setting Thermocouples Function 130 mm 130 mm Select Thermocouples from the Work mode menu to set them up. The thermocouples (TC) can work in three different ways depending on what is needed. · Control: the unit maintains the selected temperature. 100 mm ·... -
Page 8: Work Mode
Max. Rate º 1.6ºC/s Selected 120 º 14:15 Work Mode º º º º Max. Rate Power C 100 P 100 P 100 º º º P 100 º º 1.6ºC/s Temperature Mode: Select Temp. mode from the Work mode menu. In this mode, the heater unit maintains the selected Selected 120 º... - Page 9 para manuales - color gris 200 mm Work Mode 130 mm 130 mm Temperature Mode: This function allows you to set a maximum value for the temperature increase per second when heating. Select Temp. mode from the Work mode menu. In this mode, the heater unit maintains the selected temperature for the TC1 thermocouple as long as the other TC’s do not reach the control/protection The maximum heating rate value can be set between 0.1ºC/s and 2.0ºC/s (2) or “None”...
- Page 10 º º º Profile Modes Select Profile Mode from the Work Mode Menu. In this mode the heater unit regulates the temperature of the TC1 thermocouple according to the selected profile as long as the other TCs do not reach the control/protection temperature limit.
-
Page 11: Profile Editor
para manuales - color gris 200 mm Profile Editor 130 mm 130 mm The Profile editor can be opened from the main menu or from the Profiles mode work screen by pressing the ‘OK’ button. In this mode, you can edit as many as 25 profiles of temperature. 100 mm Profi... -
Page 12: Process Analysis
Process Analysis By pressing Graphics in the main MENU, the temperature of TC1 thermocouple and power fi gures in real time are displayed. Graphics 14:15 Power (%) Temperature (ºC) Power [%] Ext. Temp [ºC] Switch Y Axis Between Power and Temperature System Notifications The following icons will be displayed on the screen’s status bar. - Page 13 Press the pedal to start heating and press again to stop as if it were the button on the console. Once the Work Mode is set, the Heater Unit can work without the console using the pedal. P405 Pedal (not included) PHBE Preheater Unit...
-
Page 14: Maintenance
Maintenance Before carrying out maintenance or storage, always allow the equipment and the support to cool down. - Check periodically that the Pre Heater and Sliding the Support are clean - especially the Guide support sliding guides axes. Axes - Use a damp cloth when cleaning. Alcohol can only be used to clean the metal parts. - Only if it is absolutely necessary and if cleaning with isopropyl alcohol (IPA) is not enough, it is recommended to use a scraper to remove dirt in the glass area. - Page 15 para manuales - color gris 200 mm Safety 130 mm 130 mm It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion. 100 mm - Do not use the units for any purpose other than PCB preheating. Incorrect use may cause a fire. - The mains cable must be plugged into approved bases.
- Page 16 Notes...
- Page 17 para manuales - color gris 200 mm Notes 130 mm 130 mm 100 mm 80 mm 60 mm 50 mm 40 mm...
- Page 18 Notes...
-
Page 19: Specifications
130 mm PHBEK Preheater Set for PCBs up to 36x28cm/14x11” 100 mm Ref. PHBE-9KB 100V. Input 100V 50/60Hz. Fuse 20A Ref. PHBE-1KB 120V. Input 120V 50/60Hz. Fuse 20A Ref. PHBE-2KB 230V. Input 230V 50/60Hz. Fuse 10A - Total Net Weight: 9.7 kg / 21.38 lb... - Page 20 Warranty JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour. Warranty does not cover product wear or misuse. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased.