Advertisement
(119IO) ULTRA XTR™ RECTANGULAR / PRISM FRAME™ POOLS ENGLISH 7.5" X 10.3" PANTONE 295U 05/19/2022
POOL SETUP ( continued )
You may have purchased this pool with the Intex Krystal Clear™ filter pump. The pump has its
own separate set of installation instructions. First assemble your pool unit and then set up the
filter pump.
Estimated assembly time 60~90 minutes. (Note the assembly time is only approximate and
individual assembly experience may vary.)
1.
• Find a flat, level location that is free and clear of stones, branches or other sharp objects that may
puncture the pool liner or cause injury.
• Open the carton containing the liner, joints, legs, etc., very carefully as this carton can be used to
store the pool during the winter months or when not in use.
• Remove the ground cloth (14) from carton. Spread
it out completely with its edges being at least
5 - 6' (1.5 - 2.0m) from any obstacle such as walls,
fences, trees, etc. Remove the liner (15) from carton
and spread it out over the ground cloth with the
drain valve towards the draining area. Place the
drain valve away from the house. Open it up to
warm it in the sun. This warming will make
installation easier. Make sure the liner is centered
atop the ground cloth. Be sure to face the end with
the 2 hose connectors towards the electrical power
source.
IMPORTANT: Do not drag the liner across the
ground as this can cause liner damage and pool
leakage (see drawing 1).
• During the set-up of this pool liner, point the hose
connections or openings in the direction of the
electric power source. The outer edge of the
assembled pool is to be within reach of the
electrical connection for the optional filter pump.
2.
Remove all the parts from the carton(s) and place
them on the ground in the location where they are
to be assembled. Check the parts listing and be sure
all the pieces to be assembled are accounted for
(see drawings 2.1-2.4).
IMPORTANT: Do not start assembly if any pieces
are missing. For replacement pieces call the
Consumer Service telephone number in your area.
After all pieces are accounted for move the pieces
away from the liner for of installation.
NOTE: Sprinkle some talcum powder over the
horizontal beams before sliding them into the pool
liner sleeve. This will make removal of the beams
from the liner easier during the disassembly of the
pool.
SAVE THESE INSTRUCTIONS
5 - 6' (1.5 - 2.0m)
LINER
5 - 6'
(1.5 - 2.0m)
ELECTRICAL SOURCE
CORNER JOINT
(A)
(B)
(B)
(F)
LINER
(D)
(A)
(C)
(B) (B)
CORNER JOINT
157-1/2"x78-3/4"x39-3/8" /15' X 9' /16' X 8'/ 18' X 9'
CORNER JOINT
(A)
(B)
(F)
LINER
(E)
(D)
CORNER JOINT
118-1/8"x68-3/4"
CORNER
JOINT
(A)
(B) (B)
(B) (B)
(F)
(E)
LINER
(D)
(C)
(B)
(B) (B)
(B)
CORNER
JOINT
24' X 12'
119
English
A
1
5 - 6'
(1.5 - 2.0m)
2.1
CORNER JOINT
(C)
(D)
(F)
CORNER JOINT
2.2
CORNER JOINT
(C)
(D)
(E)
(F)
CORNER JOINT
2.3
CORNER
JOINT
(C)
(D)
(E)
(F)
(A)
CORNER
JOINT
Page 8
Advertisement
Chapters
Troubleshooting
