Advertisement
184700/1/2/3-1/2/3 (18470X-X)
INSTRUCTION MANUAL
LED EMERGENCY LIGHTING EQUIPMENT
UNIVERSAL INPUT
CLASS 2 OUTPUT
IMPORTANT SAFEGUARDS
WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. To prevent electric shock, switch off the mains power supply until installation is complete and AC
power is supplied to this product.
2. To reduce the risk of electrical shock, disconnect both normal and emergency power supplies and
connector of this product before servicing.
3. This product requires an un-switched AC power supply of 120-277V, 50/60Hz.
4. Make sure all connections are in accordance with the National or Canadian Electrical code and any
local regulations.
5. This product is for use with LED loads and provides minimum 90 minutes illumination under the
emergency mode.
6. The 184700/1/2/3-1 are UL Component Recognized for factory installation. The 184700/1/2/3-2/3
are UL Listed for field installation, and use with grounded, UL Listed, damp location rated fixtures.
7. Use this product in 0°C minimum, 50°C maximum ambient temperatures.
8. This product is suitable for use in dry or damp locations. Do not mount it near gas, heaters, air
outlets or other hazardous locations.
9. Do not attempt to service the batteries. A sealed, non-maintenance battery is used that is not field
replaceable. Contact the manufacturer for information or service.
10. This product should be mounted in locations and at heights where it will not readily be subjected to
tampering by unauthorized personnel.
11. The use of accessory equipment not recommended by the manufacturer may cause an unsafe
condition and void warranty.
12. Do not use this product for other than intended use.
13. Installation and service should be performed by qualified service personnel.
THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-METAL HYDRIDE BATTERY.
THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
Ni-MH
WWW.PHENIXLIGHTING.COM
SAVE THIS INSTRUCTIONS
E308866
14E21
BC
Advertisement
Table of Contents
Related Manuals for Phenix 184700-1/2/3
Summary of Contents for Phenix 184700-1/2/3
- Page 1 184700/1/2/3-1/2/3 (18470X-X) INSTRUCTION MANUAL 14E21 LED EMERGENCY LIGHTING EQUIPMENT UNIVERSAL INPUT CLASS 2 OUTPUT E308866 IMPORTANT SAFEGUARDS WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. To prevent electric shock, switch off the mains power supply until installation is complete and AC power is supplied to this product.
- Page 2 18470X-X MODEL SPECIFICATION MODEL VOLTAGE OUTPUT * EMERGENCY OUTPUT (CONSTANT) 184700-1/2/3 10-60 VDC 5 WATTS 184701-1/2/3 11-60 VDC 9 WATTS 15 WATTS 184702-1/2/3 15-60 VDC 184703-1/2/3 25-60VDC 25 WATTS * Max. output voltage in emergency mode is 58.5 with +tolerance of 1.5 volts.
- Page 3 WIRING 1. The 18470X-X requires an unswitched AC power supply of 120-277 volt, 50/60Hz. 2. The 18470X-X and AC driver must be on the same branch circult. Ensure the output current of the AC driver does not exceed 5A. 3. Refer the wiring diagrams below for wiring. Consult the factory for other wiring diagram. WIRING DIAGRAM FOR 184700/1/2/3-1 LED Driver (unswitched)
- Page 4 WIRING CONFIGURATION The 18470X-X series have different wiring configurations as below. 184700/1/2/3-1 Terminal block with external battery pack, choosing the different combination of the DIP switches and the corresponding battery pack to have different 18470X-X model with different emergency power output. Battery Model Power...
- Page 5 OPERATION / TESTING / MAINTENANCE OPERATION When AC ower is appli d, the LED test switch is illuminated indicating that the batteri s are being charged. When C power fails, the 70X-X automatically switches to emergency power , operating the lighting load at rated emergency power.
- Page 6 GUIDELINE FOR FIELD INSTALLATION The 18470X-2/3 series model is suitable for field installation with suitable LED loads including LED luminaires, LED lamps and others. Follow below 3 steps to determine if your luminaire is eligible for field installation. 1) Determine Electrical Compatibility A) Verify that the LED Driver for normal operation is Class 2 compliant.
Need help?
Do you have a question about the 184700-1/2/3 and is the answer not in the manual?
Questions and answers