Download Print this page

Advertisement

Quick Links

184804
INSTRUCTION MANUAL
PARALLELABLE MODULAR INVERTER
PURE SINUSOIDAL AC OUTPUT
OUTPUT VOLTAGE AUTO SETTING TO INPUT VOLTAGE
PATENTED APD TECHNOLOGY - AUTO PRESET DIMMING THE
CONNECTED LOAD IN EMERGENCY MODE
AUTO DIMMING (0-10V) OF CONNECTED LOAD UP TO 4000W
MODULAR DESIGN, FLEXIBLY PARALLELABLE COMBINATION FROM 1 TO 5 MODULES
IMPORTANT SAFEGUARDS
WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. To prevent electric shock, switch off the mains power supply until installation is complete and AC
input power is supplied to this product.
2. This product requires an unswitched AC power supply of 120-277V, 50/60Hz.
3. Make sure all connections are in accordance with the National or Canadian Electrical code and
any local regulations.
4. To reduce the risk of electrical shock, disconnect both normal power, emergency power supplies
and unit connector of this product before servicing.
5. For emergency operation of LED, incandescent, fluorescent fixtures and screw-base lamps.
6. Use this product in 0°C minimum, 50°C maximum ambient temperatures (Ta).
7. This product is suitable for use in dry or damp locations. Do not use outdoors. Do not mount
it near gas, heaters, air outlets or other hazardous locations.
8. Do not attempt to service the batteries. A sealed, non-maintenance battery is used that is not
field replaceable. Contact the manufacturer for information or service.
9. The use of accessory equipment not recommended by the manufacturer may cause an unsafe
condition and void warranty.
10. Do not use this product for other than intended use.
11. Installation and service should be performed by qualified service personnel.
12. This product should be mounted in locations and at heights where it will not readily be subjected
to tampering by unauthorized personnel.
THIS PRODUCT CONTAINS A RECHARGEABLE LiFePO
THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
LiFePO
4
WWW.PHENIXLIGHTING.COM
BATTERY.
4
SAVE THIS INSTRUCTIONS
15F21

Advertisement

loading
Need help?

Need help?

Do you have a question about the 184804 and is the answer not in the manual?

Questions and answers

Summary of Contents for Phenix 184804

  • Page 1 184804 INSTRUCTION MANUAL 15F21 PARALLELABLE MODULAR INVERTER PURE SINUSOIDAL AC OUTPUT OUTPUT VOLTAGE AUTO SETTING TO INPUT VOLTAGE PATENTED APD TECHNOLOGY - AUTO PRESET DIMMING THE CONNECTED LOAD IN EMERGENCY MODE AUTO DIMMING (0-10V) OF CONNECTED LOAD UP TO 4000W...
  • Page 2: Installation

    INSTALLATION CAUTION: MAKE CERTAIN THE AC POWER IS OFF AND THE BATTERY SWITCH IS OFF UNTIL THE INSTALLATION IS COMPLETE. 1. SPECIFICATION OF 184804 Max. Output power Quantity of 184804 Voltage 400W 1 (Single) Input Output 800W 2 (Parallelable) 120V/60Hz...
  • Page 3 INSTALLATION CEILING GRID MOUNTING INSIDE THE LUMINAIRE LED Test Switch 3/14 WWW.PHENIXLIGHTING.COM...
  • Page 4 INSTALLATION PARALLELABLE MOUNTING 1/3 INSIDE THE LUMINAIRE 4/14 WWW.PHENIXLIGHTING.COM...
  • Page 5 INSTALLATION PARALLELABLE MOUNTING 2/3 INSIDE THE LUMINAIRE 5/14 WWW.PHENIXLIGHTING.COM...
  • Page 6 INSTALLATION PARALLELABLE MOUNTING 3/3 INSIDE THE LUMINAIRE 6/14 WWW.PHENIXLIGHTING.COM...
  • Page 7 WIRING CAUTION: DO NOT SWITCH ON THE BATTERY SWITCH UNTIL INSTALLATION IS COMPLETE. 1. The 184804 requires an unswitched AC power supply of 120-277 volt, 50/60Hz. 2. Refer to the wiring diagrams below. Make connections in the following order. 3. Consult the factory for other wiring diagrams.
  • Page 8 WIRING PARALLELABLE 184804 FOR 0-10V DIMMABLE EMERGENCY LIGHTING SYSTEM MAX. DIMMABLE LOAD = 2000W @ 120V 4000W @ 277V ANY QUANTITY FLUORESCENT FLUORESCENT FLUORESCENT FLUORESCENT INCANDESCENT INCANDESCENT INCANDESCENT INCANDESCENT LUMINAIRE LUMINAIRE LUMINAIRE LUMINAIRE FOR EMERGENCY FOR EMERGENCY 0-10V DIMMER NEUTRAL...
  • Page 9 WIRING PARALLELABLE 184804 FOR NON-DIMMABLE EMERGENCY LIGHTING SYSTEM MAX. LOAD = 800W (2x184804) =1200W (3x184804) =1600W (4x184804) ANY QUANTITY =2000W (5x184804) FLUORESCENT FLUORESCENT FLUORESCENT FLUORESCENT INCANDESCENT INCANDESCENT INCANDESCENT INCANDESCENT LUMINAIRE LUMINAIRE LUMINAIRE LUMINAIRE FOR EMERGENCY FOR EMERGENCY NEUTRAL Switch 120-277 VAC...
  • Page 10 WIRING SINGLE 184804 FOR 0-10V DIMMABLE EMERGENCY LIGHTING SYSTEM (WITH 1,2 OR 3 CIRCUIT BREAKERS) MAX. DIMMABLE LOAD = 2000W @ 120V 4000W @ 277V FLUORESCENT FLUORESCENT INCANDESCENT INCANDESCENT LUMINAIRE LUMINAIRE FOR EMERGENCY FOR EMERGENCY ANY QUANTITY FLUORESCENT FLUORESCENT FLUORESCENT...
  • Page 11 WIRING SINGLE 184804 FOR NON-DIMMABLE EMERGENCY LIGHTING SYSTEM (WITH 1,2 OR 3 CIRCUIT BREAKERS) MAX. LOAD=400W FLUORESCENT FLUORESCENT INCANDESCENT INCANDESCENT LUMINAIRE LUMINAIRE FOR EMERGENCY FOR EMERGENCY ANY QUANTITY FLUORESCENT FLUORESCENT FLUORESCENT FLUORESCENT INCANDESCENT INCANDESCENT INCANDESCENT INCANDESCENT LUMINAIRE LUMINAIRE LUMINAIRE LUMINAIRE...
  • Page 12 WIRING PARALLELABLE 184804 FOR 0-10V DIMMABLE EMERGENCY LIGHTING SYSTEM (WITH 1,2 OR 3 CIRCUIT BREAKERS) MAX. DIMMABLE LOAD = 2000W @ 120V 4000W @ 277V FLUORESCENT FLUORESCENT INCANDESCENT INCANDESCENT LUMINAIRE LUMINAIRE FOR EMERGENCY FOR EMERGENCY ANY QUANTITY FLUORESCENT FLUORESCENT FLUORESCENT...
  • Page 13 WIRING PARALLELABLE 184804 FOR NON-DIMMABLE EMERGENCY LIGHTING SYSTEM (WITH 1,2 OR 3 CIRCUIT BREAKERS) MAX. LOAD = 800W (2x184804) =1200W (3x184804) =1600W (4x184804) =2000W (5x184804) FLUORESCENT FLUORESCENT INCANDESCENT INCANDESCENT LUMINAIRE LUMINAIRE FOR EMERGENCY FOR EMERGENCY ANY QUANTITY FLUORESCENT FLUORESCENT INCANDESCENT...
  • Page 14: Operation / Testing / Maintenance

    184804 switches the system back to normal mode of operation and resumes battery charging. The minimum emergency operation time is 90 minutes. A short term discharge test may be conducted after the 184804 has been charging for 1 hour. Charge for 24 hours before conducting a long term discharge test. TESTING AND MAINTENANCE The following Periodic testing is recommended to ensure the system is working correctly.