Texas A/S WRX2000 User Manual page 11

Assembly
Figure 3
Connect the upper part of the housing and the bottom
part of the housing together
Figure 4
Mounting the wheel.
Insert the axle of the wheel into the mounting hole
Push the wheel to the suitable location.
Figure 5
Mounting the guard.
Fit the guard hood as shown and secure with 2 screws
Figure 6
Fit the brush (Fig. 6a/Item A) onto the drive axle (Fig.
6a/Item B). Make sure that the brush fits accurately into
the mount (Fig. 6a/Item C). The shaft must be fixed in
order to fasten the brush. To do so, insert the pin (Fig.
2/Item 10) into the recess on the shaft (Fig. 6b) and
hold with one hand. Using the open-ended wrench (Fig.
2/Item 11), tighten the nut (Fig. 6b/Item 12).
Warning! Always take away the battery before inserting
or removing a brush
Figure 7
Height adjustment.
Undo the union nut (Fig. 7/Item 5) until the paving
scraper's handle can be moved in and out freely. Now
set the required working height and secure the handle
in this position by tightening the union nut again.
Figure 8
Adjusting the additional handle.
Undo the adjustment lock (Fig. 8/Item 3) for the
additional handle until it can be moved forwards and
backwards without any great resistance. Set the
required position and tighten the securing screw again.
Figure 9
Installing the battery.
Press the side push lock buttons of the battery pack as
shown in Fig. 9 and push the battery pack into the
mount provided. Make sure that the push lock buttons
latch in place! To remove the battery pack, proceed in
reverse order.
Operation
Use the electric weed cleaner to remove weeds
between flagstones and pavers.
Adjust the support handle, so you have the best
possible control of the machine
Activate brush by activating handle with fingers, while
locking mechanism on the side of the handle is
activated. Release both to stop.
Do not press the brush down onto the surface. This will
increase the pressure on the brush and decrease its
working life. Extension cords longer than 50 feet must
not be coiled, but must be rolled out, lying loosely on
the ground.
Move the brush forward and backwards between the tile
grooves. It is most effective when the brush is being
pulled backwards.
Warning!
When the appliance stops because no more battery
power, don't start it again. It can damage the battery.
The battery is not fully charged when delivered, please
ensure it is fully charged before you use it the first time.
Charge it 1 hour the very first time.
If the machine cannot work when turn on the switch, it
means the battery is out of power. Recharge it.
Always disconnect power before replacing brush!
Remember!
You can buy additional brushes:
Nylon brush:
Steel brush
Battery
Fig. 10b
Not included for solo machines*
To get the best performance of the chainsaw, it is
recommended to use the 4.0 Ah battery.
Warning: Do not try to disassemble, short circuit or put
it to extreme heat or fire, as it can cause serious inquiry
and permanent damage to the battery!
Battery pack is not fully charged when delivered.
Charging
•
Only use the original charger with
art. no. 90063242 or 90063241.
•
Before the battery is being used the first time, it is
recommended to fully charge it first.
LED lights
All LEDs are lit
LED 1, LED 2, LED 3
are lit.
LED 1, LED 2
are lit.
LED 1 are lit
LED 1 flashes
Note: The indicator lighs is only indicative indications,
and is not accurate power indications.
Important: To protect the battery from total
discharge, the machine will stop, when the battery is
nearly empty.
The machine must not be started up again after
automatic shutdown, as it can damage the battery.
The battery must be recharges before the work can
continue.
Art. no. 90063100
Art. no. 90063090
Battery Pack
Fully charged (75-100%).
The battery pack is
50%-75% charged
The battery pack is
25%-50% charged.
The battery pack is
0%-25% charged
The battery pack is empty.
Charge the battery.
11