Entrotec RH3+ - Telephone Instructions

Overview

GENERAL NOTES
The door entry phone system is designed so that you have a limited time to answer a call and allow the caller access or not. This is to save inconvenience to other users of the system.

For AC/DC Buzzer Handsets

1. When called up the telephone will give a distinctive buzzing tone.
2. To answer the call remove the handset from the cradle and speak to the caller.
3. To let the caller gain access, simply push the lock release button and keep it depressed for approximately 5 seconds to allow the visitor gain access.
4. When you have completed this, replace the handset in it's cradle.

PRIVACY SWITCH

5. If you do not wish to be disturbed or annoyed by nuisance calls, press the privacy switch (the LED will illuminate to remind you that the handset is in privacy mode). When in this mode the call tone is muted until you reset the switch by pressing it again.

RH3+ Connection Details & Jumper Link Settings

Notes: All Jumper Links Shown set to ED series handset configurations (as standard). See below for other settings in Terminal Number/ID. See note for Call Tone Isolation link 'PL5'

Terminal Number/ID.

1. Door Release Trigger (DR).This output goes low when the Door Release switch SW5 is pressed. Note: This is a low going pulse of a few milliseconds and provides an anti-lockdown circuit. To bypass this circuit and have a permanent trigger when the switch is pressed move LK6 to 'Non/RH' position. For AC/DC Buzzer systems select the 'Non' mode.
   Note: The handset must be lifted to use the Door Release Button.
2. DC Input (VT). The handset will function with a DC input range between 11-15v DC.
3. 0v Input (0v). The handset is designed to work on systems that use a common ground/0v supply for its reference point.
4. Call Tone or Buzz Input (BZ). The handset will accept various call inputs, a generated tone, 12v AC ring or a 12v DC ring. To use a generated tone or 12v AC ring LK7 & LK10 jumpers (Call Tone Input Selection 1 & 2) should be set for ED/Tone input. To use 12v DC ring (using internal piezo buzzer) set LK7 & LK10 to Buzz/RH position.
5. Handset microphone Output (S2). Speech output from handset to the speaker in the front panel.
6. Handset Speaker Input (S1). Speech input from the microphone in the front panel to the handset earpiece.
7. Door Status Input (DS). Input signal from the front door to advise that the door is open and illuminates DS (Green LED). This is as standard a NO contact at the door when closed. A switched 0v input is set as standard with the jumper links at PL3 linked between NEG/DS on both sides of PL3 (Switched 0v). A switched 12v input may be used, to do this move both Door Status Input Select Links to the DS/POS position.
8. Amplified Call Tone Output (EX). The 'EX' connection is an amplified version of the call tone input on the 'BZ' terminal. It amplifies the input from 2.5v-12v DC call tone to the voltage available at the handset (11-15v DC). It is imperative that this terminal is only used to extension sounders, flashing beacons and other AUX equipment including additional handsets added.
9. Call Back (SW4) Output (CB). The 'CB' connection is for concierge systems and is used for calling the concierge. This output could also be used to trigger additional door(s) via timer/relays or trigger other equipment. The output is NO going closed with switched 0V.
10. 'X' Connection Throughput (X). The 'X' connection is merely a connection point for ease of wiring. It has no connection to any circuitry on the handset.
11. Alarm Input 11-15v DC (ALM). The 'ALM' input is used to sound the internal Piezo sounder when a 11-15v DC input is applied.

RH3+ HANDSET CONNECTION DIAGRAM

Installer Please Note:

1. All RH3+ handsets are fitted with a Call Tone Volume adjustment. This maybe adjusted to suit level required. Manufactured in the UK Factory setting is full volume.
2. Terminal 8 must only be connected to an Extension Sounder, Flashing Beacon or other Aux. Equipment.

DATE: 011/02/2011	DRG.NO.	DESC.	DRAWN BY: V.A.Turner
ENTROTEC LTD Access House 5 Ashwood Court. Oakbank Livingston EH53 0TL. TEL.01506 886230 FAX.01506 886233	WIR/SCH0111/ 001/Rev1V	WIRING DIAGRAM AND COLOUR SCHEME FOR RH3+ HANDSETS
ALL CABLES TO BE KEPT WELL AWAY FROM HIGH VOLTAGE CABLES. PLEASE CONSULT OUR INSTALLATION GUIDELINE SHEET OR CONTACT OUR TECHNICAL DEPT. FOR ADVICE ON 08448586370.