Table of Contents
Related Manuals for NCT M&H IRT35.70
Summary of Contents for NCT M&H IRT35.70
- Page 1 M&H IRT35.70 INFRARED TOOL SETTER OPERATING INSTRUCTIONS M&H IRT35.70 INFRARED TOOL SETTER OPERATING INSTRUCTIONS NCT Ipari Elektronikai Zrt. 1 / 19 26 May 2023 H-1148 Budapest, Fogarasi út 7. Phone: +36 1 467 6300 www.nct.hu...
-
Page 2: Table Of Contents
Battery Replacement ....................16 Stylus Change ......................16 Maintenance of the Tool Setter ................. 17 Optical Status Display ....................18 NCT Ipari Elektronikai Zrt. 2 / 19 26 May 2023 H-1148 Budapest, Fogarasi út 7. Phone: +36 1 467 6300... -
Page 3: Description
The EC Declaration of Conformity can be found at the end of these operating instructions. If required, a copy of the signed original declaration of conformity may be requested from the address given on the back cover. NCT Ipari Elektronikai Zrt. 3 / 19 26 May 2023 H-1148 Budapest, Fogarasi út 7. -
Page 4: Validity
Power Supply (alternative) 1x Batterie (3 V / CR2) Standby: 12 months Weight (without base plate) kb. 750 g NCT Ipari Elektronikai Zrt. 4 / 19 26 May 2023 H-1148 Budapest, Fogarasi út 7. Phone: +36 1 467 6300 www.nct.hu... -
Page 5: Dimensions
Resonant Frequency Test Passed Dimensions The dimensions of the tool setter are shown in the figure below. Figure 2 Dimensions NCT Ipari Elektronikai Zrt. 5 / 19 26 May 2023 H-1148 Budapest, Fogarasi út 7. Phone: +36 1 467 6300... -
Page 6: Transmission-/Reception Area
The transmission range of the receiver for switching thetool setter ON/OFF amounts to: IRR91.40/IRR91.42: ≤ 4.0 m IRR91.50: ≤ 6.0 m Figure 3 Reception Area during ON/OFF NCT Ipari Elektronikai Zrt. 6 / 19 26 May 2023 H-1148 Budapest, Fogarasi út 7. -
Page 7: Transmission Area During Operation
1x Cylindrical stylus (35.10-D37/24) 1x Break shaft adapter M4 (91.00-S-M4-HF) 2x Battery (3,6 V / ½ AA) (4316) Tool box (35.70-TB) NCT Ipari Elektronikai Zrt. 7 / 19 26 May 2023 H-1148 Budapest, Fogarasi út 7. Phone: +36 1 467 6300... -
Page 8: Accessories
Clamping screw AF 3 mm 0548 Grub screw M2.5x3 3240 Service cover 3455 O-Ring 16x1 Viton 2906 Metal eyelid 2931 Conical spring NCT Ipari Elektronikai Zrt. 8 / 19 26 May 2023 H-1148 Budapest, Fogarasi út 7. Phone: +36 1 467 6300 www.nct.hu... - Page 9 Description Illustration 35.70-MAGNET KIT Magnet Kit for IRT 35.70, consisting of: 1x Cylindrical magnet 1x Cylindrical screw 1x Washer NCT Ipari Elektronikai Zrt. 9 / 19 26 May 2023 H-1148 Budapest, Fogarasi út 7. Phone: +36 1 467 6300 www.nct.hu...
-
Page 10: Operation
V-Slots and adjustment bolts must be clean and free of chips and must be blown off using compressed air! When positioning the tool setter, ensure that the index screw head is in the correct hole! NCT Ipari Elektronikai Zrt. 10 / 19 26 May 2023 H-1148 Budapest, Fogarasi út 7. -
Page 11: Mounting Directly On The Machine Table
When positioning the tool setter, ensure that the index screw head is in the correct hole! Figure 6 Mounting directly on the Machine Table NCT Ipari Elektronikai Zrt. 11 / 19 26 May 2023 H-1148 Budapest, Fogarasi út 7. -
Page 12: Setting Infrared Transmission Range And Switch Off Time
HIf the stylus of the tool setter is not deflected for a specified time the tool setter switches off automatically. This time can be set to 120 ~ 180 s. 1. Remove the tool setter as shown below. NCT Ipari Elektronikai Zrt. 12 / 19 26 May 2023 H-1148 Budapest, Fogarasi út 7. - Page 13 220 h 145 d ≤ 1.6 m 120 s 440 h 240 d 290 h 170 d * Factory preset NCT Ipari Elektronikai Zrt. 13 / 19 26 May 2023 H-1148 Budapest, Fogarasi út 7. Phone: +36 1 467 6300 www.nct.hu...
-
Page 14: Aligning The Stylus
For measurement only one system can be used at one point in time. Figure 9 Tool Setter Activation Aligning the Stylus Figure 10 Aligning the Stylus NCT Ipari Elektronikai Zrt. 14 / 19 26 May 2023 H-1148 Budapest, Fogarasi út 7. -
Page 15: Tool Setter Calibration
Effective length of the tool setter Response time of the tool setter in relation to the NC Calibration of the tool setter is performed using control specific calibration cycles. NCT Ipari Elektronikai Zrt. 15 / 19 26 May 2023 H-1148 Budapest, Fogarasi út 7. -
Page 16: Battery Replacement
2. Loosen the grub screws A, B and C of the cylindrical stylus (refer to Figure 13) and remove the break shaft. NCT Ipari Elektronikai Zrt. 16 / 19 26 May 2023 H-1148 Budapest, Fogarasi út 7. -
Page 17: Maintenance Of The Tool Setter
3. Clean tool setter and parts under flowing water. 4. Reassemble all parts. 5. Align the stylus centre. 6. Calibrate the tool setter. NCT Ipari Elektronikai Zrt. 17 / 19 26 May 2023 H-1148 Budapest, Fogarasi út 7. Phone: +36 1 467 6300... -
Page 18: Optical Status Display
Tool setter is transmitting signals. LED blinking green/red Low Battery. LED blinking orange Stylus deflected. LED constantly red Wrong battery type. NCT Ipari Elektronikai Zrt. 18 / 19 26 May 2023 H-1148 Budapest, Fogarasi út 7. Phone: +36 1 467 6300 www.nct.hu... - Page 19 M&H IRT35.70 INFRARED TOOL SETTER OPERATING INSTRUCTIONS NCT Ipari Elektronikai Zrt. 19 / 19 26 May 2023 H-1148 Budapest, Fogarasi út 7. Phone: +36 1 467 6300 www.nct.hu...
Need help?
Do you have a question about the M&H IRT35.70 and is the answer not in the manual?
Questions and answers