Dc mems accelerometer, 2.5v offset, 66.6 mv/g, +/- 30g, +6 to 30 vdc excitation, 4-pin connector (11 pages)
Summary of Contents for PCB Piezotronics 3711F11100G
Page 1
Model 3711F11100G Single Axis MEMS DC accelerometer, 14 mV/g, +/-100 g, 1/4-28 4-Pin Plug Installation and Operating Manual For assistance with the operation of this product, contact the PCB Piezotronics, Inc. Toll-free: 716-684-0001 24-hour SensorLine: 716-684-0001 Fax: 716-684-0987 E-mail: info@pcb.com...
Assistance is needed to safely operate equipment PCB Piezotronics is an ISO-9001 certified company whose Damage is visible or suspected calibration services are accredited by A2LA to ISO/IEC Equipment fails or malfunctions 17025, with full traceability to SI through N.I.S.T.
Page 3
CAUTION Refers to hazards that could damage the instrument. NOTE Indicates tips, recommendations and important information. The notes simplify processes and contain additional information on particular operating steps. The following symbols may be found on the equipment described in this manual: This symbol on the unit indicates that high voltage may be present.
Page 5
Component Name Hazardous Substances Lead (Pb) Mercury (Hg) Cadmium (Cd) Chromium VI Polybrominated Polybrominated Compounds Biphenyls (PBB) Diphenyl Ethers (Cr(VI)) (PBDE) Housing PCB Board Electrical Connectors Piezoelectric Crystals Epoxy Teflon Electronics Thick Film Substrate Wires Cables Plastic Solder Copper Alloy/Brass This table is prepared in accordance with the provisions of SJ/T 11364.
Page 6
3700 series DC Accelerometer Operating Guide General OPERATING GUIDE for use with High Sensitivity DC ACCELEROMETERS PCB ASSUMES NO RESPONSIBILITY FOR DAMAGE CAUSED TO THIS PRODUCT AS A RESULT OF PROCEDURES THAT ARE INCONSISTENT WITH THIS OPERATING GUIDE Introduction Principle of Operation This operating guide contains information that will familiarize the user with the basic operation and installation of the 3700 The sensor element of the 3700 series features a proof mass,...
3700 series DC Accelerometer Operating Guide Typical Measurement System facturers for their de-bonding recommendations. The de-bond- ing agent must be allowed to penetrate the surface in order to The 3700 series DC Accelerometers are available in a uniaxial properly react with the adhesive, so it is advisable to wait a few or triaxial package.
3700 series DC Accelerometer Operating Guide words, when the sensor is mounted perpendicular with the 10.0 Maintenance and Repair Earth’s surface, the offset will equal that as specified on the calibration certificate for “zero-g offset voltage.” If the Because of the sophisticated nature of PCB instrumentation, sensor is mounted parallel with the Earth’s surface, the sen- field repair of the equipment is not recommended.
Page 9
Model Number Revision: NR DC RESPONSE ACCELEROMETER 3711F11100G ECN #: 49223 Performance ENGLISH OPTIONAL VERSIONS Sensitivity(± 3 %) 13.5 mV/g 1.38 mV/(m/s²) Optional versions have identical specifications and accessories as listed for the standard model except where noted below. More than one option may be used.
Page 10
PCB Piezotronics Inc. claims proprietary rights in REVISIONS the information disclosed hereon. Neither it nor any reproduction thereof will be disclosed to others DESCRIPTION without the written consent of PCB Piezotronics Inc. ELECTRICAL CONNECTOR RELEASED TO DRAFTING 49223 4 PIN, HERMETIC...
Page 11
PCB Piezotronics Inc. claims proprietary rights in the information disclosed hereon. Neither it nor any reproduction thereof will be disclosed to others DESCRIPTION without the written consent of PCB Piezotronics Inc. - SEE SHEET 1 - "SERVICE LOOP" TAPE, PETRO WAX...