Cleaning the unit / Pre filter replacement Combined filter replacement iQ display features / Visual alarms Visual alarms (cont’d) USB connectivity / USB upload USB download Information collected by USB Fault indication / Error codes Consumable spares / Filter disposal FumeCAB 1000 iQ specifications...
Page 3
Overview Filter Door Panel Control Panel Combined Filter LCD Display Company Branding Door Latches Pre Filter Hinged Perspex enclosure panel Air Inlet Filter Release Handle...
Page 4
Overview USB Port Mains Isolation Switch Motor Cooling Air outlet Mains Inlet Inlet for Tools/Equipment/Cables...
Important (Refer to manual) BOFA Technical Service If a problem arises with your FumeCab 1000 iQ system, or if Refers to handling tip and other particularly useful it displays a fault code, please refer to the troubleshooting information.
Page 7
Serial Number Label Safety Instructions Warning and Information labels Location: Top left corner of back panel. The following listing details labels used on your FumeCab Meaning: This label contains a variety of information about 1000 iQ unit. the extraction unit, including. Goggles, Gloves &...
Page 8
2. Open the front door. Check the filters are located in their correct position The FumeCab 1000 IQ features a hinged transparent before closing the door and securing the door latches. Perspex panel on the front of the unit. This allows for more...
Page 9
ESD Compliant FumeCAB 700 Please follow the above specification when selecting the An ESD compliant version of the FumeCAB 1000 iQ is also power supply outlet for the iQ system, ensure the power available. This unit features an internal anti-static mat with supply is suitable before connecting the iQ system.
Page 10
Operation Turning extraction unit On There are 2 stages to powering up your iQ extraction unit. Firstly the main isolation switch must be switched to the “On” position, the top side of the switch should be depressed to power the unit. This will place the extraction unit in Standby mode, indicated by the front panel power button glowing Red.
Operation Setting the desired airflow The iQ system features automatic flow control. This enables the user to set the required airflow rate, then over time as the filters begin to block the motor will automatically begin to increase in speed to compensate for any loss in performance caused by the added restriction of the partially blocked filters.
3) The airflow will stabilise, and the buttons will turn green Operation to show the airflow has set. Airflow Auto Adjust (first installation only) When first setting the airflow on your new extraction unit the iQ will detect if the desired airflow is achievable with the installation that has been connected to the extraction unit.
extractor would be significant. It is therefore essential to Maintenance minimise this risk by undertaking an appropriate assessment to determine:- a). Whether additional fire protection equipment should be installed. b). Appropriate maintenance procedures to prevent the risk Maintenance UK of build-up of debris which could potentially combust. It is a legal requirement, under regulation 9 of the COSHH regulations that all local exhaust ventilation systems are thoroughly examined and tested at least once every 14...
Remove the pre filter from the tray and replace it with a new, unused BOFA pre filter. Once removed it is recommended that the used filters are bagged and sealed.
Inlet Blocked Alarm iQ System Display The iQ system features a 2 stage inlet blocked alarm. • Partial inlet blockage • Full inlet blockage Partial hose blocked alarm This alarm will become active when the iQ system detects a part blockage in the installation. The iQ system interprets a iQ Display Features partial blockage as a vacuum spike within the inlet but is The iQ display has the ability to display all the faults...
Page 16
If the VOC level in the exhaust exceeds the PPM (Parts per million) level pre-set at BOFA then the Gas alarm will be triggered and display the Gas icon as shown below.
iQ System Display USB Connectivity The iQ system is equipped with a USB drive, that operates as a 2 way device, as detailed below. • Duplicating iQ settings • Download iQ Data The USB port is located on the top left hand side of the unit. Duplicating iQ settings (USB Upload) This USB upload feature has been designed for customers that have multiple extractors and specific set of parameters...
Page 18
iQ System Display Download iQ Data (USB Download) With this feature the customer is able to download all stored data within the iQ system, this information can then be used to keep records of how your iQ system is performing, this is also very beneficial for the technical team when diagnosing issues with the extraction system.
Page 19
BOFA helpline. Combined filter % blockage The display on the extractor will show the combined filter...
In the event of an error code being displayed please contact Motor Failure your local representative or BOFA who will be able to If the extraction unit develops a fault relating to the motor diagnose the fault and advise on the most efficient solution.
The To maintain performance it is important that the filters are thresholds for these risks replaced with identical BOFA filters. To re-order please refer can then be compared with to the Filter number printed on the filter installed in your the amount of material in extraction unit.
Page 22
System Specifications Unit: FumeCab 1000 iQ Face Velocity: 0.4m/s Weight: 120Kg (264lbs) Motor: Centrifugal Fan Output: 1100w Electrical supply: 230V Hertz: 50/60Hz Full Load Current: 12.5A Noise Level: Below 60dB (A) (at typical operating speed) Size: Metric Imperial (mm) (inches)
Need help?
Do you have a question about the FumeCAB 1000 iQ and is the answer not in the manual?
Questions and answers