Related Manuals for Smithco 41-000A
Summary of Contents for Smithco 41-000A
- Page 1 Operator’s Sand Star CVT Model 41-000A 2WD Mechanical June 2023 Product Support: Hwy SS & Poplar Ave; Cameron WI 54822 1-800-891-9435 productsupport@smithco.com...
-
Page 2: Table Of Contents
CONTENTS tion 1-11 Introduction ............1-9 Introduction ..................1 Symbols .....................2 Safety ....................3 Warning Decal Location ..............4 Safe Practices ...................5 Specifications ...................6 Setup ....................7 Controls & Instruments ..............8-9 Service ............10-14 Operation ..................10 Daily Checklist ................. 11 Service Charts .................12 How To Rake A Sand Trap ..............13 Battery .....................14 Reference ............ -
Page 3: Contents Tion
All Smithco machines have a Serial Number and Model Number. Both numbers are needed when ordering parts. Serial number tag is located on left rear ROPs mount post. Refer to engine manual for placement of engine serial number. -
Page 4: Symbols
Hand Throttle Oil Level Park Brake Slow Park Brake Lift Arm Fast Release Hydraulic Fluid Hot Surface No Riders Moving Parts Pinch Point Penetration 20° MAX Rollover Warning Headlamp Blower Seat Belt Danger Danger Caution PARTS MANUALS AVAILABLE ONLINE AT smithco.com... -
Page 5: Safety
It may also be used to alert against unsafe practices. IMPORTANT: Blue. Indicates procedures which should be followed to avoid damage to the machine. PARTS MANUALS AVAILABLE ONLINE AT smithco.com... -
Page 6: Warning Decal Location
Decal, Dash Panel 27-077 Decal, Round Smithco 16-088 Decal, Warning 25-277 Decal, Battery 41-091 Decal, Sand Star 25-373 Decal, Smithco Star, Small 25-374 Decal, Smithco Star, Large 25-370 Decal, DbA 88 25-354 Decal, Tire Pressure 5PSI PARTS MANUALS AVAILABLE ONLINE AT smithco.com... -
Page 7: Safe Practices
19. Stop engine before making repairs/adjustments or checking/adding oil to the crankcase. 20. Use parts and materials supplied by Smithco only. Do not modify any function or part. These machines are intended for professional maintenance on golf courses, sports turf, and any other area maintained turf and related trails, paths and lots. -
Page 8: Specifications
Minimum of 87 octane Alternator 10 Amp WHEELS & TIRE Front: 20 X 10 - 10 Turf Tires 5 psi (.34 bar) Smithco # 52-120 Rear: 25 X 10 - 12 Turf Tires 5 psi (.34 bar) Smithco # 45-617 SPEED Forward Speed 0 to 12 m.p.h. -
Page 9: Setup
SETUP The Bunker Rakes arrive from Smithco with some assembly required before service. 1. Set park brake. Push the brake down past center and the park brake is engaged. 2. Rear wheel mounting. Block front tire. Jack up rear of machine being careful not to damage underside of machine. -
Page 10: Controls & Instruments
Seat adjustment lever is located under front of seat on left side. It allows seat adjustment forward or backward for operator's comfort. The seat also has the start safety switch in it. To start the Sand Star the operator must be sitting on the seat. PARTS MANUALS AVAILABLE ONLINE AT smithco.com... - Page 11 To lower, pull inward to release pin from hole (M) and push downward to selected depth. Release pin into closest slotted hole (L). To raise pull inwards and pull back, placing pin in top lock hole (M). PARTS MANUALS AVAILABLE ONLINE AT smithco.com...
-
Page 12: Service
Check oil level more frequently if using these types of oils. SAE 30 oil, if used below 40° F (4° C), will result in hard starting and possible engine bore damage due to inadequate lubrication. PARTS MANUALS AVAILABLE ONLINE AT smithco.com... -
Page 13: Daily Checklist
Before servicing or making adjustments to the machine, stop engine, set park break, block wheels and remove key from ignition. Follow all procedures and ONLY use parts prescribed by the manufacturer. Read the engine manual before maintenance. PARTS MANUALS AVAILABLE ONLINE AT smithco.com... -
Page 14: Service Charts
Check the Instrumentation Inspect electrical system for frayed wires Check park brake adjustment Change oil filter. Change oil. Lubricate Machine Ensure all warning decals are intact. Areas of Concern Inspection Performed by: Item Date Information PARTS MANUALS AVAILABLE ONLINE AT smithco.com... -
Page 15: How To Rake A Sand Trap
After exiting trap, secure machines in accordance with practices described in this manual. Rake trap edges, slopes and “enter /exit” area with a hand rake. After returning to maintenance area, thoroughly clean machine, check fluids, and lubricate as advised in this manual. PARTS MANUALS AVAILABLE ONLINE AT smithco.com... -
Page 16: Battery
4. Connect other end of cable (D) to engine block on unit being started. Solenoid To prevent damage to other electrical components on unit being started, make certain that engine is at idle speed before disconnect- ing jumper cables. PARTS MANUALS AVAILABLE ONLINE AT smithco.com... -
Page 17: Reference
Widna tal-Operatur ▪ Dopuszczalny poziom hałasu dla operatora ▪ Nível sonoro nos ouvidos do operador ▪ Nivelul zgomotului la urechea operatorului ▪ Hladina hluku pôsobiaca na sluch operátora ▪ Raven hrupa pri ušesu upravljavca ▪ Nivel sonoro en el oído del operador ▪ Ljudnivå vid förarens öra PARTS MANUALS AVAILABLE ONLINE AT smithco.com... - Page 18 Hyväksyntänumero ▪ Numéro de certificat ▪ Bescheinigungsnummer ▪ Αριθμός Πιστοποιητικού ▪ Hitelesítési szám ▪ Numero del certificato ▪ 41000-01 Sertifikāta numurs ▪ Sertifikato numeris ▪ Numru taċ-Ċertifikat ▪ Numer certyfikatu ▪ Número do Certificado ▪ Număr certificat ▪ Číslo osvedčenia ▪ Številka certifikata ▪ Número de certificado ▪ Certifikatsnummer PARTS MANUALS AVAILABLE ONLINE AT smithco.com...
- Page 19 30 days from discovery of the condition. If you need help locating an Authorized Smithco Distributor, or if you have questions regarding your warranty rights or responsibilities, you may contact us at: Smithco Product Support Department 200 West Poplar Ave.
- Page 20 This warranty does not apply to normal “wear and tear” items. Normal “Wear and Tear” includes, but is not limited to, damage to seats due to wear or abrasion, worn painted surfaces, scratched decals or windows, etc. Smithco may require the return of failed parts or components in order to determine the validity of any warranty claim.
Need help?
Do you have a question about the 41-000A and is the answer not in the manual?
Questions and answers