Table of Contents
Advertisement
Quick Links
Fan Kit #2767/FK26
for Radiance, Stardance, Dutchwest & Oxford Gas Heaters and Defiant
NC, FB & CAT-C, Dutchwest NC, Encore NC, FB & CAT-C, Wood Stoves
Please read these instructions before proceeding with
installation.
Kit contents
• Fan Assembly with Rheostat and Snapstat
• Fan Mounting Bracket for RVF33
• Snapstat Mounting Bracket
• Rheostat Bracket (Defiant NC, FB & CAT-C / Encore NC,
FB & CAT-C)
• 1/4 - 20 x 3/4" hex head screws, (4)
• 1/4 - 20 hex nuts, (2)
• 1/4" Star Washers, (2)
• #8 Star Washer, (1)
• #10 Sheet Metal Screws, (2)
• Retaining Nut (1)
• Control Knob
• Wire Tie
Tools Needed
• Flat blade screwdriver
• Work gloves
• Phillips screwdriver
It is easiest to install the fan before the stove is connected
to the gas supply line. Compare the contents of the fan kit
with the list above and Figure 1 to confirm that you have all
of the parts.
!
Avoid any drafts that alter burner flame patterns. Do
not allow fans to blow directly into the fireplace.
This optional fan kit is equipped with a three-pronged
(grounding) plug for your protection against shock
hazard and should be plugged directly into a properly
grounded three-pronged receptacle. Do not cut or
remove the grounding prong from this plug.
- Installation Instructions
WARNING
Fan Kit contents.
1/4" Star
1/4-20 x 3/4"
Hex Bolts
Washer
RVF33 ONLY
Fan Mounting
Bracket
1/4-20 Hex
Nuts
Fan
Assembly
This kit fits several different stoves; follow the procedures for
Rad2767 Fan Kit Parts.eps
your specific stove. Match these instructions to the model
name and/or number on the stove's instructions or nameplate.
MOTOR
BLK
ON/OFF
RHEOSTAT
#2767 / FK26 Fan wiring diagram.
ST236
FK26 wiring diagram
12/99
RDV40, RNV40,
RVF33, SDV30
Snapstat Bracket
#8 Star Washer
#10 Sheet
Snapstat
Metal Screws
1/4-20 x 3/4"
Hex Bolts
1/4"Star
Washer
Defiant /Encore
Rheostat Wire
Rheostat Bracket
Harness Assy
Connect to PC Board
on RF Models Only
BLK
SNAPSTAT
WHT
2003135_R19 • 10/19
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Hearth & Home 2767/FK26
Summary of Contents for Hearth & Home 2767/FK26
- Page 1 Fan Kit #2767/FK26 - Installation Instructions for Radiance, Stardance, Dutchwest & Oxford Gas Heaters and Defiant NC, FB & CAT-C, Dutchwest NC, Encore NC, FB & CAT-C, Wood Stoves Fan Kit contents. RDV40, RNV40, 1/4” Star 1/4-20 x 3/4” RVF33, SDV30 Hex Bolts Washer...
-
Page 2: Table Of Contents
Fan Kit #2767/FK26 - Installation Instructions for Radiance, Stardance, Dutchwest & Oxford Gas Heaters and Defiant NC, FB & CAT-C, Dutchwest NC, Encore NC, FB & CAT-C, Wood Stoves Table of Contents Radiance Direct Vent RADVT ................3 RDV40................. 3 RDVOD ................ -
Page 3: Radiance Direct Vent Radvt
Radiance Direct Vent - RADVT 3. Secure the fan assembly to the bottom plate with two (2) 1/4 - 20 x 3/4” hex head screws and one (1) 1/4” star 1. Remove the rear shroud panel (Figure 6) and fasten the washer. (Figure 3) blower assembly to the firebox back with the two bolts provided. (Figure 7) 2. Attach the snapstat assembly to the snapstat bracket with two sheet metal screws. Attach the snapstat bracket to Side Shield the side shield. (Figure 7) 3. The rheostat control switch attaches to the left side of the Snapstat... -
Page 4: Rdvod
2. Attach the snapstat assembly to the snapstat bracket with two (2) sheet metal screws. Attach the snapstat bracket Rheostat Knob to the side shield. (Figure 7) Retaining Nut 3. The rheostat control switch attaches to the left side of the T'STAT valve bracket at the front of the stove. (Figure 9) • Rheostat Remove retaining nut from shaft of rheostat. (if pre- installed) Pilot Assembly Blower Figure 5 - Install rheostat into switch box. RDVOD ST151 1. Remove the rear shroud panel (Figure 6) and fasten rdv install rheostat the blower assembly to the firebox back with the two 10/99 White (2) bolts provided. (Figure 7) White White Dots NOTE: Steps 2 and 3 do not apply when the RF valve is used. After attaching blower assembly to the firebox, run Antenna the spliced female leads to the front of the stove and attach Valve to back of Honeywell RF Comfort valve. (Figure 8) (Bottom View) -
Page 5: Natural Vent Rnv40
Radiance Natural Vent - RNV40 1. Remove the rear skirt. Use work gloves to protect your hands. Remove six (6) sheet metal screws around the Switchbox edge of the draft hood opening. (‘A’, Figure 10) Remove 1/4- Rheostat 20x1/2” Assy. the rear skirt cover plate: three (3) screws hold it on. Rheostat Hex Bolts (‘B’,Figure 14) Remove one (1) sheet metal screw holding... -
Page 6: (Serial #'S Up To 1456 (Rnvodrn), 1944 (Rnvodrp)
8. Fasten the switch box to the rear skirt with a sheet metal 2. Position the fan behind the rear shroud. (Figure 15) Pass screw as shown in Figure 12. Tighten the Phillips bolt the fan rheostat assembly and snapstat assembly beneath holding the switch box to the rear skirt and the stove. the stove toward the front. 9. Replace the rear skirt cover plate with three (3) sheet 1/4-20 x metal screws as shown at “C”, Figure 12. The top edge 1/2” Hex of the cover plate goes inside the rear skirt. Replace Bolts a sheet metal screw at each side of the fan assembly, holding the rear skirt to the inner fan shield. (‘D’, Figure Star Washer 10. Plug the fan cord into a standard grounded 110 volt Snapstat household outlet. -
Page 7: (Serial #'S Starting At 1457 (Rnvodrn), 1945 (Rnvodrp)
4. Attach the snapstat housing to the snapstat bracket with 2. Carefully pull the shroud assembly away from the rear of two (2) sheet metal screws and one (1) #8 star washer. the stove. (Figure 15) 3. With the rear shroud assembly in the upright position, set 5. Attach the snapstat bracket, with the snapstat assembly the bottom of the shroud on a padded surface to prevent attached, to the horizontal surface on the inside of the rear scratching the surface. Unfasten the four phillips head shroud. Use a sheet metal screw. There are pre-drilled screws which attach the outer shroud to the inner duct holes at each corner of the panel for this. The vertical part assembly. - Page 8 • 6. Position the fan assembly so the ducts slide between the Attach the control knob to the rheostat shaft. inner and outer shroud. The inner shroud should engage • Use the wire tie to secure the fan and rheostat wire with the two (2) slots in the ends of the bracket so that harnesses together. bracket and shroud are interlocked. (Figure 21) Secure the bracket with the four (4) sheet metal screws provided in the finish bag. Outer Slot Shroud Inner Shroud Slot Retaining Nut Control Knob ST347a Figure 23 - Attach rheostat to left side of valve. 13. Plug the power cord into a standard grounded 110 volt FK28 household outlet.
-
Page 9: Rvf33
RVF33 1. Remove the rear shroud. Use work gloves to protect Heat Shield against sharp edges. Loosen the two (2) screws on each side just enough to disengage the shroud panel from the sides of the stove. (Figure 24) 2. Remove the switch box. (Figure 24) • Remove the sheet metal screw and washer from the left side (as you face the rear of the stove) of the switch box. Use Lower Hole •... -
Page 10: Ruvs40
Radiance Unvented (RUVS40): The fan kit includes a ‘snapstat’, a temperature sensing switch which will be mounted to the blower duct just below the top plate of the stove. The snapstat automatically turns the fan on or off at approximately 109°F. These directions are oriented facing the rear of the stove. Position the fan under the rear shroud as shown in Figure 28. Pinch Grommet 1. Open the left side of rear shroud. (Figure 28) to Remove • Remove the round head phillips screws (B) that secure the shroud to the side of the stove. • Remove the sheet metal screw (C) that fastens the switchbox to the rear shroud. -
Page 11: Ruvsod
RUVSOD Snapstat 1. Loosen the four (4) phillips head screws which secure the Wire Rheostat Wire rear shroud to the stove sides. (Figure 34) 2. Carefully pull the shroud assembly away from the rear of the stove. Fan Bracket 3. With the rear shroud assembly in the upright position, set the bottom of the shroud on a padded surface to prevent scratching. Unfasten the four (4) phillips head screws which attach the outer shroud to the inner duct assembly. NOTE: If you are installing the fan kit after the stove is in its final location, follow same steps, except disengage only the right side of the outer shroud. - Page 12 5. Connect snapstat leads. Disconnect the snapstat module 8. Refasten the outer shroud to the inner duct assembly. from the leads inside the snapstat bracket. (Figure 36) 9. Install the snapstat by loosening the front screw on the Bend open the snapstat bracket. Use needlenose pliers inner side of the duct. (Figure 38) Slide the snapstat under to remove the black plastic grommet from the bracket. the head of the screw and tighten. Connect the leads to Discard the bracket. Insert the grommet and wires into the the snapstat.
-
Page 13: Stardance Direct Vent Sddvt
Stardance Direct Vent - SDDVT 1. Remove the rear skirt insert panel at the bottom of the Rear Skirt (Figure 40) and fasten the blower assembly to the firebox back with the two Phillips pan-head bolts originally installed in the firebox back. (‘A’, Figure 41) Rheostat Control Rear Skirt Retaining Nut Sheet Metal Control Knob Screws Figure 42 - Attach rheostat to left side of valve. ST347a FK28 rheostat install 9/21/00 Rear Skirt Panel Figure 40 - Remove rear skirt panel. -
Page 14: Sdv30
SDV30 4. If the stove has already been installed, replace the valve cover plate with two (2) sheet metal screws. The bottom 1. Remove the panel at the bottom of the rear skirt (Figure of the stove’s rating plate and lighting instructions plate 43) and remove two (2) Phillips head bolts from the bottom should protrude through the slot at the top right corner of of the firebox back. Fasten the blower assembly to the the cover plate. If the gas line and/or switch wires have firebox back with two (2) Phillips head bolts and one (1) not yet been attached to the valve, leave the valve cover 1/4” star washer. (‘A’, Figure 44) plate off until the rest of the installation is complete. 5. Plug the fan cord into a standard grounded 110 volt Rear Skirt household outlet. -
Page 15: Sdv30R
SDV30R Star Washer 1. Remove the rear skirt insert panel at the bottom of the Sheet Metal rear skirt (Figure 47) and fasten the blower assembly to Screws Phillips the firebox back with the two (2) phillips pan head bolts Snapstat Pan Head originally installed in the firebox back. (‘A’, Figure 48) Bolts 1/4”-20 NOTE: Steps 2 and 3 do not apply when the RF valve is Hex Bolt used. After attaching the blower assembly to the firebox, run the spliced female leads to the front of the stove and attach Star... - Page 16 4. Pass the rheostat cord under the firebox. If the control valve cover panel has not yet been installed, set it in rough The blower assembly mounts to the two studs at the lower position in front of the firebox. Leave the control panel rear shroud. The rheostat attaches to the front control valve off until you have attached the gas line and connected cover panel. the switch wires. (Figure 52) Align the locating pin on the NOTE: The #2767/FK26 Fan Kit includes mounting hardware rheostat stem with the smaller hole in the Control Panel. that is not used on the Stardance Natural Vent heater. Fasten the rheostat stem to the Control Panel with the 1. Remove the cover plate at the bottom of the rear shroud. retaining nut. (‘A’, Figure 50) 2. Remove the hex nuts from the two mounting studs located at the lower center of the rear shroud. (‘B’, Figure 50)
-
Page 17: Snv30 (Drop-In Burner)
Sheet Metal Screw Star Washer Sheet Metal Screw Insert flange behind lip of Hex Nuts shroud opening Figure 56 - Attach the snapstat and fan assembly to the rear shroud. • Remove retaining nut from shaft of rheostat. (if pre- ST589 installed) Figure 54 - Reattach the cover plate; fasten rear shroud to firebox • Insert the rheostat through the hole in the back of the attach snapstat drafthood assembly if the fan installation is part of first assembly left side of the valve bracket, aligning the locator pin of stove. -
Page 18: (Serial #'S Starting At 5251 (Snv30Rn), 5484 (Snv30Rp)
Snapstat Bracket Snapstat Module Pinch Grommet to Remove Insert the flange behind the lip of the shroud opening. Figure 60 - Remove the snapstat and grommet from the bracket. Figure 58 - Reattach the cover plate and secure the rear shroud ST670a to the firebox draft hood assembly. - Page 19 Slot Outer Shroud Inner Shroud Slot Rheostat Rheostat Retaining nut Rheostat Knob Figure 64 - Attach fan rheostat. ST347a FK28 Figure 62 - Position the fan to engage the inner shroud with the fan bracket slots and secure with sheet metal screws. rheostat install ST194 attach fan to shroud 9/21/00 11/99 Snapstat Left Air Duct Figure 63 - Install the snapstat and connect the extension wire terminals. View is with top removed, however, access is available through the rear when installing fan before gas line connection.
-
Page 20: Dutchwest Direct Vent/Natural Vent
Dutchwest & Oxford Direct Vent/Natural Vent • Thread the retaining nut onto the shaft of the rheostat, NOTE: The #2767 / FK26 Fan Kit may include parts that are tightening with a wrench. Do not overtighten. not used on the Dutchwest/Oxford gas stoves. • Attach the control knob to the rheostat shaft. 1. Remove the rear skirt insert panel at the bottom of the rear • Use the wire tie to secure the fan and rheostat wire skirt (Figure 65) and fasten the blower assembly to the harnesses together. -
Page 21: Dutchwest Nc
Slot Snapstat Bracket Outer Shroud Snapstat Module Pinch Grommet Inner Shroud to Remove Slot Figure 71 - Position the fan to engage the inner shroud with the fan bracket slots and secure with sheet metal screws. ST194 Figure 69 - Remove the snapstat and grommet from the bracket. attach fan to shroud ST670a Snapstat Left Air Duct 11/99 3. Disassemble the inner shroud from the outer shroud by RUVSOD snapstat removing the four screws, two on each side. -
Page 22: Defiant Nc/Fb/Cat-C
Defiant NonCat / Flexburn Encore NonCat / Flexburn 1. Attach the fan assembly at the bottom edge of the inner 1. Attach the fan assembly at the bottom edge of the inner back with two (2) 1/4-20 x 3/4” hex head screws, Figure back with two (2) 1/4-20 x 3/4” hex head screws and one (1) 1/4” star washer, Figure 74. 2. Attach snapstat to the mounting holes on the underside 2. Attach snapstat to the mounting holes on the underside of the bottom with two (2) 1/4-20 pan head screws. of the bottom with two (2) 1/4-20 pan head screws.
Need help?
Do you have a question about the 2767/FK26 and is the answer not in the manual?
Questions and answers