Hearth & Home GFK-160A Installation And Operating Instructions

Fan kit

Advertisement

Quick Links

Introduction

The GFK-160A fan has been designed to circulate room
air through the fireplace to enhance heat output. The
GFK160A fan system operates on 120 VAC, 60 Hz power.
This is available through a receptacle in the factory installed
junction box. The junction box is located in the controls
compartment of the fireplace.
A variable speed control is provided with the fan system
to provide quiet forced air flow at the desired speeds. A
temperature sensor switch, which automatically turns the
fan ON/OFF, is also provided with this kit.
NOTE: The variable speed control and temperature
sensor switch are not used with some remote control
systems.

Kit Contents:

Compare system components in Figure 1 with the actual
parts received. If any parts are missing or damaged, con-
tact your dealer before starting installation. Do not install
a damaged fan kit.
CAUTION! Do not install damaged components.
FAN
CONTROL
KNOB
CONTROL
NUT
SPEED
CONTROL
Figure 1. System Components

Installation Precautions

The GFK-160A Fan Kit is tested and safe when installed in
accordance with this installation manual. It is your respon-
sibility to read all instructions before starting installation and
to follow these instructions carefully during installation to as-
sure maximum benefit from, and safe operation of, the fan.
1
Hearth & Home Technologies • GFK-160A Blower System Installation Instructions • 107-981 Rev R • 1/18
GFK-160A Fan Kit
- Installation and Operating Instructions -
WING
NUT
TEMPERATURE
SENSOR
SWITCH
This fan is carefully engineered and must be installed only
as specified. If you modify it or any of its components, you
may cause a fire hazard and will void the WARRANTY. In
addition, such action may void the coverage provided by
the owner's home insurance.
CAUTION: All wiring should be done by a qualified
electrician and shall be in compliance with local
codes and with the National Electric Code ANSI/NFPA
NO. 70-current (in the United States), or with the cur-
rent CSA C22.1 Canadian Electric Code (in Canada).

Installation Instructions

WARNING: Risk of Shock! Turn electrical power off
at the circuit breaker before beginning this installa-
tion.
NOTE: The factory installed junction box in the gas
fireplace must be wired with 110 VAC before installing
this kit. See Installation Instructions section.

Installing the Fan

Position the fan all the way to the rear and center
in the fireplace. Pull the blower forward 1/8" to 1/4"
from the back wall of the fireplace. See Figure 2.
Thread fan cord plug through hole on bottom of cord bracket
and plug into receptacle labeled "FAN" on power cord.

Installing the Speed Control and Sensor Switch

If using a remote control system that utilizes fan control,
disregard steps 1-3 and follow remote control installation
instructions.
1. Remove the knob and locknut from the variable speed
control. Slide the control behind the fireplace wall, in,
with the stem sticking out of the pre-punched hole which
is often in the lower right front corner. Attach the lock-
nut tightly and reattach the knob on the stem. Turn the
speed control switch to the "ON" position.
NOTE: Some models may have a separate mounting
location on the control panel or valve bracket for mount-
ing this speed control.
2. Slide the temperature sensor switch/bracket assembly
onto the weld stud on the outside of the combustion
chamber. Secure the bracket assembly with the wing
nut provided. See Figure 3.
NOTICE: The weld stud is located either on the lower right
side or the bottom of the combustion box.
NOTICE: The switch/bracket assembly must be installed
so that the sensor switch is facing the combustion box
surface.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GFK-160A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Hearth & Home GFK-160A

  • Page 1: Installation Instructions

    Hearth & Home Technologies • GFK-160A Blower System Installation Instructions • 107-981 Rev R • 1/18...
  • Page 2: Service Parts

    3 to 2 prong adapter will be required to be obtained from an independent source. your dealer. Figure 2. Junction Box Styles SERVICE PARTS Part Number Description SRV107-570A Hardware Bag Hearth & Home Technologies • GFK-160A Blower System Installation Instructions • 107-981 Rev R • 1/18...
  • Page 3 For the location of your nearest Hearth & Home Technologies dealer, please visit www.hearthnhome.com. Hearth & Home Technologies 7571 215th Street West, Lakeville, MN 55044 www.hearthnhome.com Hearth & Home Technologies • GFK-160A Blower System Installation Instructions • 107-981 Rev R • 1/18...

Table of Contents