Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for NEC X461HB-R
Summary of Contents for NEC X461HB-R
- Page 1 User’s Manual MultiSync X461HB...
-
Page 2: Table Of Contents
Index Declaration of conformity ... English-1 Important Information ... English-2 WARNING, CAUTION ... English-2 Declaration ... English-2 Safety Precautions, Maintenance & Recommended Use ... English-3 Contents ... English-4 Installation ... English-5 Parts Name and Functions ... English-7 Control Panel ... English-7 Terminal Panel ... -
Page 3: Declaration Of Conformity
Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. OmniColor is a registered trademark of NEC Display Solutions Europe GmbH in the countries of EU and Switzerland. All other brands and product names are trademarks or registered trademarks of their respective owners. -
Page 4: Important Information
WARNING CAUTION European U.K. Continental EU (except U.K.) U.K. Declaration of the Manufacturer and marked with Warning English-2 Chinese Japanese China NEC Display Solutions, Ltd. 4-13-23, Shibaura, Minato-Ku Tokyo 108-0023, Japan Japan... -
Page 5: Safety Precautions, Maintenance & Recommended Use
• Cable distribution system should be grounded (earthed) in accordance with ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable. • The screen of the coaxial cable is intended to be connected to earth in the building installation. -
Page 6: Contents
Contents Your new MultiSync monitor box* should contain the following: • LCD monitor • Power cord* • Video Signal Cable • Wireless Remote Control and AA Batteries • Setup Manual Video Signal Cable (Mini D-SUB 15 pin to Mini D-SUB 15 pin) Power Cord* CD-ROM Type and number of power cords included will depend on the where the LCD monitor is to be shipped. -
Page 7: Installation
Please note the following when mounting on wall or ceiling • When using mounting accessories other than those that are NEC approved, they must comply with the VESA- compatible (FDMlv1) mounting method. • NEC strongly recommends Unit using size M6 screws... -
Page 8: Attaching Mounting Accessories
The protective sheet was wrapped around the LCD in the original packaging. Make sure there is nothing on the table that can damage the monitor. When using mounting accessories other than NEC compliant and approved, they must comply with the VESA- compatible mounting method. -
Page 9: Parts Name And Functions
Parts Name and Functions Control Panel POWER button Switches the power on/off. See also page 16. MUTE button Switches the audio mute ON/OFF. INPUT button Acts as SET button within OSD menu. (Toggle switches between [DVI], [VGA], [RGB/HV], [HDMI], [DVD/HD1], [DVD/HD2], [SCART], [VIDEO1], [VIDEO2], [S-VIDEO] or [TV]*). -
Page 10: Terminal Panel
Terminal Panel Main Power Switch On/Off switch to turn main power ON/OFF. AC IN connector Connects with the supplied power cord. HDMI connector To input digital HDMI signals. DVI IN (DVI-D) To input digital RGB signals from a computer or HDTV device having a digital RGB output. - Page 11 Kensington Lock For security and theft prevention. EXTERNAL SPEAKER TERMINAL To output the audio signal from AUDIO 1, 2, 3, HDMI and TV jack. Note: This speaker terminal is for 15W + 15W (8 ohm) speaker. Option board slot Slot for board accessories. Please contact your supplier for detail information.
-
Page 12: Wireless Remote Control
Wireless Remote Control POWER button Switches the power on/standby. INPUT button Selects input signal. DVI: DVI VGA: VGA RGB/HV: RGB/HV HDMI: HDMI DVD/HD: DVD/HD1, DVD/HD2, SCART VIDEO: VIDEO1, VIDEO2 S-VIDEO: S-VIDEO OPTION: Depend on your connection PICTURE MODE button Selects picture mode, [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA], [AMBIENT1], [AMBIENT2]. -
Page 13: Operating Range For The Remote Control
REMOTE ID button Activates REMOTE ID function. MTS button* Multichannel television sound. AUDIO INPUT button Selects audio input source [IN1], [IN2], [IN3], [HDMI], [TV]*. button* Activates closed captioning (For U.S.). *: The product you purchased may not have this feature. Operating Range for the Remote Control Point the top of the remote control toward the LCD monitor’s... -
Page 14: Setup
C. Replace the cover. CAUTION: Incorrect usage of batteries can result in leaks or bursting. NEC recommends the following battery use: • Place “AA” size batteries matching the (+) and (-) signs on each battery to the (+) and (-) signs of the battery compartment. - Page 15 5. Attach the cable cover • Use six of the M4 x 10 screws (included) to attach the cable cover. 6. Switch on the power of all the attached external equipment When connected with a computer, switch on the power of the computer first.
-
Page 16: Connections
Connections Before making connections: First turn off the power of all the attached equipment and make connections. Refer to the user manual included with each separate piece of equipment. Wiring Diagram DVD player with HDMI out Computer (Analog) Connected Connecting equipment terminal DVD/HD1 (3RCA) -
Page 17: Connecting A Personal Computer
Connecting a Personal Computer Connecting your computer to your LCD monitor will enable you to display your computer’s screen image. Some video cards and a pixel clock over 162MHz may not display an image correctly. Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically. <Factory preset signal timing>... -
Page 18: Basic Operation
Basic Operation Power ON and OFF Modes The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off. NOTE: The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the Power Button on the front of the LCD. -
Page 19: Power Indicator
Power Indicator Mode Status Indicator Light Power ON Green* Power OFF (Eco Standby)* Power consumption under 0.5W* Power OFF (Standby) Amber Power consumption under 2W* Power Save Amber Blinking Power consumption under 2W* Power Standby when Green and Amber blink alternately “SCHEDULE SETTINGS”... -
Page 20: Information Osd
Information OSD The Information OSD provides information such as: Monitor ID, Input Source, Picture Size, etc. Press the DISPLAY button on the remote to bring up the Information OSD. Picture Mode DVI, VGA, RGB/HV STANDARD sRGB AMBIENT1 HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO, TV* STANDARD CINEMA AMBIENT1... -
Page 21: Osd (On-Screen-Display) Controls
OSD (On-Screen-Display) Controls NOTE: Some functions may not be available depending on the model or optional equipment. Input source Main Menu Icons Main Menu Item Sub Menu PICTURE MODE Select Press UP or DOWN button to select sub-menu. Remote Control Press UP or DOWN button to select. -
Page 22: Picture
(S-Curve). DICOM SIM. DICOM GSDF curve simulated for LCD type. PROGRAMMABLE A programmable gamma curve can be loaded using NEC software. MOVIE SETTINGS NOISE REDUCTION Adjusts the amount of noise reduction. Press + or - to adjust. -
Page 23: Audio
H RESOLUTION Adjusts the horizontal size of the image. DVI, VGA, RGB/HV inputs only V RESOLUTION Adjusts the vertical size of the image. DVI, VGA, RGB/HV inputs only INPUT RESOLUTION If there is a problem with signal detection, this function forces the monitor to display the signal at the desired resolution. -
Page 24: Pip
SCHEDULE RESET Resets the following settings within the SCHEDULE menu back to factory setting: OFF TIMER, SCHEDULE SETTINGS. KEEP PIP MODE Allows the monitor to remain in “PIP” and “TEXT TICKER” mode after powering off. When Power is returned, PIP and TEXT TICKER appear without having to enter the OSD. PIP MODE Picture-in-Picture SIDE BY SIDE (ASPECT) SIDE BY SIDE ASPECT... -
Page 25: Multi Display
OSD TRANSPARENCY Set the transparency level of the OSD. TYPE1 TYPE2 OSD ROTATION Determines the OSD display direction between landscape and portrait. LANDSCAPE Display the OSD with landscape mode. PORTRAIT Display the OSD with portrait mode. INPUT NAME You can set currently displayed INPUT name as you like. Max: 8 letters, you can use Space, A-Z, 0-9, and some symbols. -
Page 26: Display Protection
DISPLAY PROTECTION POWER SAVE Sets how long the monitor waits to go into power save mode after a lost signal. Note: When connecting DVI, video card might not stop sending digital data even if image has All inputs except for TV* disappeared. - Page 27 GAIN Adjusts gain value. OFFSET Adjusts slice level of synchronized signal. SYNC TERMINATE Selects the terminate resistance for matching the cable impedance. RGB/HV inputs only TERMINAL SETTING DVI MODE Selects the kind of DVI-D equipment which is connected DVI. Select “DVI-PC” when PC or other computer equipment is connected.
- Page 28 As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
-
Page 29: Remote Control Function
Remote Control Function REMOTE CONTROL ID FUNCTION REMOTE CONTROL ID The remote control can be used to control up to 100 individual MultiSync monitors using what is called the REMOTE CONTROL ID mode. The REMOTE CONTROL ID mode works in conjunction with the Monitor ID, allowing control of up to 100 individual MultiSync monitors. - Page 30 3. Press the “DISPLAY” button on the remote control while aiming at the “PRIMARY” monitor. The Information OSD will be shown at top left side of the screen. Monitor ID: Displays the ID number of the current monitor within the daisy chain. Target ID: Displays the ID number of the monitor that to be controlled via daisy chain from the current monitor.
-
Page 31: Controlling The Lcd Monitor Via Rs-232C Remote Control
Controlling the LCD monitor via RS-232C Remote Control This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal. NOTE: When you use this function, EXTERNAL CONTROL should be “RS-232C”. When you use this function, STANDBY MODE should be “STANDBY”. Functions that can be controlled by a personal computer are: •... -
Page 32: Controlling The Lcd Monitor Via Lan Control
Controlling the LCD monitor via LAN Control Connecting to a Network Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings by using an HTTP server function. NOTE: When you use this function, EXTERNAL CONTROL should be “LAN”. When you use this function, STANDBY MODE should be “STANDBY”. -
Page 33: Network Settings
“HOSTS” file of the computer being used. Example 1: When the host name of the monitor has been set to “pd.nec.co.jp”, access is gained to the network setting by specifying http://pd.nec.co.jp/index.html for the address or the entry column of the URL. - Page 34 Alert Mail Setting http://<the Monitor’s IP address>/lanconfig.html This option notifies your computer of an error message via e-mail when using wired LAN. An error message notification will be sent when an error occurs in the monitor. HOST NAME Type in the hostname of the network connected to the monitor. Up to 60 alphanumeric characters can be used.
-
Page 35: Features
Allows for the monitor to be mounted on a wall or an arm using any third party compliant device. NEC recommends using mounting interface that comply with TÜV-GS and/or UL1678 standard in North America. -
Page 36: Troubleshooting
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. -
Page 37: Specifications
Specifications Product Specifications LCD Module Pixel Pitch: Resolution: Brightness: Contrast Ratio: Viewing Angle: Design View Distance: Frequency Horizontal: Pixel Clock Viewable Size Input Signal DVI-D 24pin Digital RGB 15pin Mini D-sub Analog RGB Sync RGB/HV BNC (R,G,B,H,V) Analog RGB Sync HDMI HDMI Connector Digital RGB... -
Page 38: Pin Assignment
Pin Assignment 1) Analog RGB input (MiniDsub15p): VGA Pin No Name Video Signal Red Video Signal Green Video Signal Blue DDC-GND Red-GND Green-GND Blue-GND 2) S-VIDEO input: VIDEO Pin No Name Y (Luminance) C (Chroma) 3) Digital RGB input (DVI-D): DVI Pin - Assignment of DVI connector: TX2- TX2+... -
Page 39: Manufacturer's Recycling And Energy Information
Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).