Salora BEAMER 45BHM2550 - 720p LED 200 ANSI Lumens Projector Manual

Safety Instruction

Installation

• To get the better watching, please use this projector while drawing the curtain or in a dark room.
• Please use this projector carefully, dropping or crashing may damage parts or result in blurred images, abnormal displaying.

Power

• Please use the power adapter that comes with this product to use the projector.
• Be careful while using the power cord, avoid to excessive bending; thedamage of power cable may cause electric shock and fire.
• It is better to unplug the power cord after power off.

Cleaning

• Unplug the power cable first.
• Clean the shell regularly with a damp cloth, neutral detergent can be used.
• Please use a glasses cloth or lens paper, and do not scratch the lens.
• Please clean projector's vents and speakers regularly by banister brush, or the vents will be blocked.

High temperature attention

• While projecting or just finishing projection, it will get hot near the air outlet. To avoid scalding, please do not touch it with your hands.
• While projecting, please do not look the lens directly, or it may hurt eyes.

Warm tips

• Do not disassemble the projector, if not, it would lead to a risk of electric shock, and also affect the normal warranty.
• Please do not put any liquid or heavy stuff on the projector.

Accessories List

Specification

Multimedia Supported Files

Structural Diagram

PaneI Functions

Bluetooth speaker mode:
Press this button to switch the projector to Bluetooth speaker mode.

Indicator light: Red: standby mode, Blue: working mode

Joystick Button: the center is the ok key and the direction can be selected by pushing the key

Hoist the machine to the ceiling

Holes for ceiling mount (M5):
Remove 4pcs cushion, holes for ceiling mount will be available.

Function Operation

1. Power
2. Aspect ratio
3. Arrow keys
4. Home
5. Menu
6. Volume Down
7. Setting
8. Screen flip
9. Source
10. Enter
11. Return
12. Volume Up
13. Mute

Power On/Off

Turn on: Connect the DC terminal of the power adapter to the DC port of the projector. When the red indicator light is on, press the power button on the panel (or press the power key on the remote control) to start the machine.

Turn off: When the projector is working normally, press the power button, the indicator light turns from blue to red, the projector is in shut down.

Focus

Image focusing

Place the projector lens perpendicularly to the projection screen or curtain wall, and adjust the focus dial until the image is clear, that means the image focusing is finished.

During the focusing process, you can play the programs or pick up the product menu images to match the focusing adjustment.

Standard Setting

Refer to the data in the table below to place the projector away from the projection screen according to the preset graphic size. When installing, place the projector on a solid, stable countertop or use a hanger to hoist it to the ceiling. The airframe should be well ventilated. Do not cover or block the vents. There should be no obstructions within 30cm of the vents.

Note: The above data is for reference only, please refer to the physical measurement.

Multimedia Play

Step1: Insert the U disk into the USB port of the projector.

Step2: Select Multimedia, and then press the OK key to enter.

Step3: Select the file to be played.

Signal Source Settings

Step1: Enter the main interface, select HDMI or AV from the following options (or press the remote control source key, and then select the source in the pop-up box).

Step2: Press the OK key to enter the options.

Main Interface

Pop-up source box

WiFi Connection

Step1: Select Settings in the main interface and press OK key to enter setting interface.

Step2: Select Network Setting.

Step3: Turn on the WiFi, find the WiFi you need to connect to, enter the password through the virtual keyboard, and confirm the connection.

iOS Cast

Step1: Select iOS Cast on the main interface.

Step2: The iOS device and the projector must be connected to the same network, or the iOS device must be connected to the wireless access point(AP) from the projector.

Step3: Select Screen Mirroring on the control center of the iOS device.

Step4: Select the corresponding projector device name.

Mirror your iPhone, iPad or iPod touch

Make sure that your iOS device is connected to the same network as your projector, or connect iOS device with AP by Projector:

NEWAP-DBB6

1. On your iOS device, open Control Center and tap screen Mirroring.
   
2. Looking for devices that can be mirrored on.
   
3. Select NETLINK-DBB6-(icast) from the list.
   

Miracast

Step1: Select Miracast on the main interface.

Step2: Turn on the Wireless Display function of the Android device.

Note: Different Android devices have different names and opening methods for the Wireless Display function. For details, please refer to the manual of the Android device you are using.

Step3: Select the corresponding projector device name.

Note: The projector and the Android device cannot be connected to different WiFi, otherwise the corresponding projector device will not be searched on the Android device.

To connect Android Mobile/Pad Device with Projetor Based on WiFi-Display Techenology

1. On your Android Mobile/Pad, open the settings menu.
2. Access your display settings or screen-mirroring.
3. Select your Miracast receiver: NETLINK-A8FE
   Waiting for connection...

iOS Cable Cast

Step1: Select iOS Cable Cast on the main interface.

Step2: Use the data cable to connect the iOS device and the projector (through the USB port of the projector).

Step3: Click Trust in the pop-up window of the iOS device.

Step4: Enter the iOS device password.

Note: If still cannot connect with projector after clicking Trust, can try to use the original data cable to reconnect.

Apple cable

1. Connect the lightning connector to the phone. Connect the other end to the projector
   
2. Click "Trust" the window that pops up on the phone.
   
3. Enter device password.