Advertisement
Quick Links
SERVICE MANUAL
T4.75F / T4.85F / T4.95F / T4.105F
T4.75F with cab PIN ZDJD10166 and above; T4.75F without cab PIN ZDJD10836 and above;
T4.85F with cab PIN ZDJD11099 and above; T4.85F without cab PIN ZDJD11022 and above;
T4.95F with cab PIN ZDJD10640 and above; T4.95F without cab PIN ZDJD10215 and above;
T4.105F with cab PIN ZDJD11527 and above; T4.105F without cab PIN ZDJD11911 and above
Part number 48017749
1
edition English
st
July 2016
Tier 3
Tractor
ENGINE - 10
CLUTCH - 18
TRANSMISSION - 21
FOUR-WHEEL DRIVE (4WD) SYSTEM - 23
FRONT AXLE SYSTEM - 25
REAR AXLE SYSTEM - 27
POWER TAKE-OFF (PTO) - 31
Advertisement
Related Manuals for New Holland ZDJD10166
Summary of Contents for New Holland ZDJD10166
- Page 1 Tier 3 Tractor T4.75F with cab PIN ZDJD10166 and above; T4.75F without cab PIN ZDJD10836 and above; T4.85F with cab PIN ZDJD11099 and above; T4.85F without cab PIN ZDJD11022 and above; T4.95F with cab PIN ZDJD10640 and above; T4.95F without cab PIN ZDJD10215 and above;...
- Page 2 INTRODUCTION 47888362 08/07/2016...
-
Page 3: Table Of Contents
Contents INTRODUCTION Note to the Owner WARNINGS FOR AIR CONDITIONING SYSTEM REPAIR OPERATIONS (*) ....................3 Advice Important notice . - Page 4 Note to the Owner WARNINGS FOR AIR CONDITIONING SYSTEM REPAIR OPERATIONS T4.105F With cab [ZDJD11527 - ] T4.75F With cab [ZDJD10166 - ] T4.85F With cab [ZDJD11099 - ] T4.95F With cab [ZDJD10640 - ] Starting the system at low temperatures can damage the compressor. Only operate the air conditioner when the engine is hot and the temperature inside the cab is at least 20 °C (68.00 °F).
-
Page 5: Advice Important Notice
INTRODUCTION Advice Important notice All maintenance and repair work described in this manual must be performed exclusively by NEW HOLLAND service technicians, in strict accordance with the instructions given and using any specific tools necessary. Anyone performing the operations described herein without strictly following the instructions is personally responsible for any eventual injury or damage to property. -
Page 6: Safety Rules Safety Regulations
INTRODUCTION Safety rules SAFETY REGULATIONS TO PREVENT ACCIDENTS Most accidents or injuries that occur in workshops are the result of non--observance of simple and fundamental safety regulations. For this reason, IN MOST CASES THESE ACCIDENTS CAN BE AVOIDED: by foreseeing possible causes and con- sequently acting with the necessary caution and care. - Page 7 INTRODUCTION • Do not run the engine in confined spaces without suitable ventilation. • Do not smoke, use naked flames, or cause sparks in the area when fuel filling or handling highly inflammable liquids. • Never use naked flames for lighting when working on the machine or checking for leaks. •...
- Page 8 INTRODUCTION • Never lubricate the vehicle when the engine is running. ELECTRICAL SYSTEMS • If it is necessary to use auxiliary batteries, remember that both ends of the cables must be connected as follows: (+) with (+) and (-) with (-). •...
-
Page 9: Personal Safety Cab Air Conditioning System
INTRODUCTION Personal safety CAB AIR CONDITIONING SYSTEM T4.105F With cab [ZDJD11527 - ] T4.75F With cab [ZDJD10166 - ] T4.85F With cab [ZDJD11099 - ] T4.95F With cab [ZDJD10640 - ] SAFETY REGULATIONS • The refrigerant must be handled with great care in order to avoid personal injury; always use safety goggles and gloves. -
Page 10: Basic Instructions
INTRODUCTION Basic instructions Battery Before carrying out any kind of service operation disconnect and isolate the battery negative lead, unless otherwise requested for specific operations (e.g: operations that require the engine running). Once the specific operation has been completed, disconnect the lead in order to complete the operation. Shimming For each adjustment operation, select adjusting shims and measure individually using a micrometer, then add up the recorder values: Do not rely on measuring the entire shimming set, which may be incorrect, or the rated value... - Page 11 − Part number of the ordered part, which can be found in the “Spare Parts Catalogue” used for order processing. Notes for equipment The tools that NEW HOLLAND propose and illustrate in this manual are: − Specifically researched and designed for use with NEW HOLLAND vehicles.
-
Page 12: Consumables
INTRODUCTION Consumables Recommended Component to be filled NEW HOLLAND International Qty. NEW HOLLAND or topped up specifications specifications products Cooling system: Water and NEW HOLLAND AMBRA Less cab 10.5 l (2.77 US gal) NH900A − AGRIFLU liquid 50% With cab 13.5 l (3.57 US gal) - Page 13 INTRODUCTION Consumables Recommended Component to be NEW HOLLAND International Qty. NEW HOLLAND filled or topped up Specifications specifications products Cooling system: Water and NEW HOLLAND AMBRA Less cab 10.5 l (2.77 US gal) NH900A – AGRIFLU liquid 50% With cab 13.5 l (3.57 US gal)
- Page 14 Engine T4.105F With cab [ZDJD11527 - ], T4.105F Without cab [ZDJD11911 - ], T4.75F With cab [ZDJD10166 - ], T4.75F Without cab [ZDJD10836 - ], T4.85F With cab [ZDJD11099 - ], T4.85F Without cab [ZDJD11022 - ], T4.95F With cab [ZDJD10640 - ], T4.95F Without cab [ZDJD10215 - ]...
- Page 15 Contents Engine - 10 [10.001] Engine and crankcase ............. . . 10.1 47888362 08/07/2016...
- Page 16 Engine and crankcase - 001 T4.105F With cab [ZDJD11527 - ], T4.105F Without cab [ZDJD11911 - ], T4.75F With cab [ZDJD10166 - ], T4.75F Without cab [ZDJD10836 - ], T4.85F With cab [ZDJD11099 - ], T4.85F Without cab [ZDJD11022 - ], T4.95F With cab [ZDJD10640 - ], T4.95F Without cab [ZDJD10215 - ]...
- Page 17 Contents Engine - 10 Engine and crankcase - 001 SERVICE Engine and crankcase - Remove ..............3 Install .
- Page 18 Engine - Engine and crankcase Engine and crankcase - Remove DANGER Heavy objects! Lift and handle all heavy components using lift- ing equipment with adequate capacity. Always support units or parts with suitable slings or hooks. Make sure the work area is clear of all bystanders.
- Page 19 Engine - Engine and crankcase 5. Disconnect the pipes (1) and (2) of the transmission oil cooler and of the front axle differential lock. MOLI11F0004AB 6. Unscrew the front and rear retaining bolts, unscrew the front pivot pin retaining screw and remove the bracket (1).
- Page 20 Engine - Engine and crankcase 9. Unscrew the transmission shaft central support (1) re- taining bolts and remove the shaft and support. MOLI11F0008AB 10. Disconnect: The transmission oil cooler pipes (1) and the front axle differential lock pipe (2). MOLI11F0009AB 11.
- Page 21 Thanks very much for your reading, Want to get more information, Please click here, Then get the complete manual NOTE: If there is no response to click on the link above, please download the PDF document first, and then click on it. Have any questions please write to me: admin@servicemanualperfect.com...