Subscribe to Our Youtube Channel
Related Manuals for Powermat PM-PP-40S
Summary of Contents for Powermat PM-PP-40S
- Page 1 PM0691 USER MANUAL PLACE IMAGE HERE PLASMA CUTTING PM-PP-40S ORIGINAL INSTRUCTIONS...
-
Page 2: Table Of Contents
TABLE OF CONTENTS SYMBOLS WARNING / INFORMATION ..................3 PURPOSE OF THE DEVICE ......................... 4 SAFETY ........................... 5 Safety during welding ..................... 5 General safety ....................7 Protection against electric shock ..................8 Electromagnetic field .......... -
Page 3: Symbols Warning / Information
SYMBOLS WARNING / INFORMATION ATTENTION: Before using the device please read the instruction manual and safety ATTENTION: Before using the device please read the instruction manual and safety instructions. Keep these instructions. ATTENTION: General warning sign notes for each user on the general danger. It is ATTENTION: General warning sign notes for each user on the general danger. -
Page 4: Purpose Of The Device
PURPOSE OF THE DEVICE Plasma cutting PM-PP-40S is designed for manual or machine air plasma, electrically conductive parts made of carbon steel and alloy steel, aluminum and its alloys, brass, copper, and iron. Special equipment allows cutting torch in confined areas and in all possible positions. The device can be used in the production processes, the work bench, repair, as well as scrap cutters. -
Page 5: Safety
SECURITY This section covers basic safety rules when working with the use of plasma cutting. SECURITY DURING WELDING SECURITY DURING WELDING ELECTRIC SHOCK CAN KILL: Welding apparatus produce a high voltage. Do not touch ELECTRIC SHOCK CAN KILL: Welding apparatus produce a high voltage. Do not touch the torch, welding material connected when the device is turned on to the network. - Page 6 liquids. Such containers or tanks should be rinsed prior to welding in order to remove flammable liquid. Do not weld near flammable gases, vapors or liquids. Fire extinguishing equipment (fire blankets and fire extinguishers powder or snow) should be located near his workstation in a conspicuous and easily accessible place.
-
Page 7: General Safety
READ INSTRUCTIONS: Carefully read the manual and follow the information READ INSTRUCTIONS: Carefully read the manual and follow the information contained therein. For any damage caused by failure to comply with the guidelines of this manual manufacturer is not liable. HIGH FREQUENCY RADIATION: High-frequency radiation can zakłucać... -
Page 8: Protection Against Electric Shock
• Never grasp the device by knives or hold it for the device protective cover. Do not move the device connected to the network, keeping your finger on / off switch. • Disconnect from the network when not in use, you want to transport them or you leave them unattended, and when you run it, or clean the control. -
Page 9: Pacemakers
OZRUSZNIKI HEART OZRUSZNIKI HEART You should consult your doctor before welding and welding being in place. The doctor will explain the procedure if any of the contact with the welding apparatus. ZYNNOŚCI WHEN CUTTING ZYNNOŚCI WHEN CUTTING a) Secure the workplace, as long as there is no fixed and mobile screens with anti przeciwodpryskowymi. b) Use for cutting electric wires and an operating handle only in good condition (intact insulation). -
Page 10: Description Of The Device
DESCRIPTION OF THE DEVICE MODEL: PM-PP-40S DESCRIPTION OF 1. LCD display (ammeter) 1. LCD display (ammeter) Gas pressure control Adjustment of gas flow Manometer power LED Socket gas conduit LED overload oil separator Adjusting the current Turbo-fan Jack ground wire... -
Page 11: Description Of Symbols On The Label
DESCRIPTION OF SYMBOLS ON THE LABEL Current (DC) Symbol single phase alternating current (AC) of the rated frequency 50Hz and 60Hz operating frequency. Nominal input voltage (AC) Nominal input voltage (AC) Nominal input voltage (AC) Maximum input current Maximum input current Maximum input current 1max 1max... -
Page 12: Technical Data
TECHNICAL DATA Model PM-PP-40S 10-40 Cutting current range Power 230V 50 / 60Hz input 6,5kVA Rated cutting current Rated duty cycle Cutting current at 100% duty cycle operating voltage 85V - 96V 12mm The maximum depth of penetration The maximum penetration depth qualitative... -
Page 13: Place Using The Unit
5. Set the parameters for the material being cut. 5. Set the parameters for the material being cut. 6. You can start the process of cutting press the button on the handle. 6. You can start the process of cutting press the button on the handle. 7. -
Page 14: Cutting Service
3. Connect the welding cables to the device, then the power cord to a single-phase network 3. Connect the welding cables to the device, then the power cord to a single-phase network the electric voltage of 230V and frequency of 50Hz. Warning! Plasma cutters are very sensitive to voltage drops in the power supply. - Page 15 Depending on the thickness of the cut material closer bracket to the workpiece at a minimum distance, but without touching, (refers to a material having a thickness up to 1.5 mm) or maintaining it at a distance of about 4 ~ 5 mm, ie. Set by a spring spacer, or the diagonal predetermined for insulating nozzle holder (for all material thickness).
- Page 16 optimum speed Too fast Maximum speed Too slow In the case where the cutting speed is too high, the flow is not able to sufficiently melt the metal and to throw it on the outside part of the cut, which may lead to direct a portion of the molten metal to the die, and thus lead to serious damage of the handle when the continuation of the cutting in these conditions.
- Page 17 In the case of solar flares arc or when the flame will be green, or arc will emit any "abnormal" sound, switch the device off immediately and check the condition of wearing parts. Continuing the cut in the "abnormal" conditions may lead to damage or destruction of the holder. cutting holes It is advisable to start from the cutting edge of the board or opening.
- Page 18 switching off the flow of compressed air through the handle is due to the need to cool the heated components of the handle. It is prohibited to turn off the device by switching the switch in the off position before the automatic closing of the air valve after the completion of the cutting process.
-
Page 19: The Most Common Disruption Cutting
- screwing the electrode pliers, followed by the formation of the "burr" on the electrode, its curvature and often the result of disturbances in the flow of plasma, etc. breakthrough. - improper installation when replacing any parts should pay special attention to whether they are designed for a particular model and that are established in the correct order. -
Page 20: Maintenance And Storage
too low cutting speed Excessive slag on the bottom cutting edge too large a thickness of the material to be cut - defective nozzle opening The main arc is not perpendicular a workpiece burned center electrode poorly folded wearing parts too high cutting speed Excess cutting edge or too big a gap... -
Page 21: Storage
Repair of power tools should only be done by qualified personnel using original spare parts. This ensures the safety of the device. Address: Powermat service ul. Defenders of the Gdansk Post 97 42-400 Zawiercie Tel. 32 670 39 68 4 internal e-mail: Tel. -
Page 22: Warranty
WARRANTY During the warranty period the buyer is entitled to free repairs due to manufacturing defects. The warranty is recognized only when the product is delivered to the point of sale in a complete state, nierozmontowany, along with proof of purchase and properly completed warranty card. YŁĄCZENIA MANUFACTURER'S WARRANTY YŁĄCZENIA MANUFACTURER'S WARRANTY Occurs when the device has the damage as a consequence of natural wear or due to improper handling of the... -
Page 23: Company Information
You can also refer to the old appliance collection point. For more information on the collection system equipment is at hand: https://sklep.powermat.pl/webpage/pl/recycling.html COMPANY DETAILS PH Powermat TMK Bijak Sp. General Partnership Ul. Defenders of the Gdansk Post 97 42-400 Zawiercie https://www.powermat.pl DECLARATION OF CONFORMITY...
Need help?
Do you have a question about the PM-PP-40S and is the answer not in the manual?
Questions and answers