Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Powermat PM-500-SSTT
Summary of Contents for Powermat PM-500-SSTT
- Page 1 USER MANUAL BELT SANDER, tray PM-500-SSTT ORIGINAL INSTRUCTIONS...
-
Page 2: Table Of Contents
Table of Contents SYMBOLS WARNING / INFORMATION ..................3 DESCRIPTION OF THE DEVICE ........................... 3 TECHNICAL DATA ..........................4 PURPOSE OF THE DEVICE ......................... 4 SAFETY RULES ........................5 Workplace ..............................5 Safety in use .......... -
Page 3: Symbols Warning / Information
SYMBOLS WARNING / INFORMATION SYMBOLS WARNING / INFORMATION You should wear hearing protection. Be used respiratory protection. You should use eye protection. DESCRIPTION OF THE DEVICE Device Working table. Blade guard. -
Page 4: Technical Data
Stopwatch. Lower blade guard ejection of waste. Rubber feet. Angle. Shield. 4mm hex wrench. TECHNICAL DATA ~ 230V / 50Hz motor power supply Engine output no-load S Engine output no-load S Engine output no-load S - 30 minutes - 30 minutes - 30 minutes 500W belt speed... -
Page 5: Safety Rules
Because of safety reasons the device can not be used by children and young people under the age of 18 and by persons under the influence of alcohol, drugs or other intoxicants. Persons who are not familiar with this manual, please read carefully before its first use. SAFETY RULES Workplace •... -
Page 6: General Thoughts
• Do not use a tool that has a damaged switch. A tool that can not be controlled with the switch creates a danger and should be repaired. • Before adjusting, repairing, changing accessories or storage, disconnect from the power tool. Such precautions will reduce the risk of accidental starting. -
Page 7: It Is Forbidden To
• If necessary, work under pressure, use tools and equipment insulation and dielectric gloves and shoes. • If the automatic switch-off or burn fuses, switch it on again when the cause of the short circuit and setting up a new fuse. •... - Page 8 2. Tighten cover drive to the device. 2. Tighten cover drive to the device. 3. Install the cover disc ejection by 4mm Allen key. 3. Install the cover disc ejection by 4mm Allen key. 4. Unscrew the four screws from the bottom cover. 4.
-
Page 9: Installing The Top Disk Grinding
Installing countertop grinding disk 1. Position the support table with a hole in the device and then place the support in 1. Position the support table with a hole in the device and then place the support in hole. 2. To avoid injury to fingers countertop should be a few millimeters from the blade. tighten 2. -
Page 10: Operation And Adjustment Device
2. Install a timer, tighten the screw. 2. Install a timer, tighten the screw. 3. Tighten the cover to the stopwatch. 3. Tighten the cover to the stopwatch. OPERATION AND CONTROL DEVICE Terms of use Humidity - max. 70% Temperature - 5 ° C to + 40 ° C The device can not be used in places with an increased risk of fire or explosion. -
Page 11: Changing The Position Of The Arm Grinding
Changing the position of the grinding arm 1. Turn off the device. 1. Turn off the device. 2. Loosen the nut, the arm in the desired position, tighten the nut. 2. Loosen the nut, the arm in the desired position, tighten the nut. Setting the angle stopper 1. -
Page 12: The Setting Angle Tabletop Grinding Wheel
The setting angle tabletop grinding wheel Use the angle to this process by applying it from one side to the disc, and on the other to the top. Sanding belt replacement 1. Loosen the nut stopwatch. 1. Loosen the nut stopwatch. 2. -
Page 13: Troubleshooting
NCES PRO BLEMÓW NCES PRO BLEMÓW Possible cause Solution Problem • ON / OFF switch is • Check switch damaged • Check all power • Device connections unplugged • Let the unit cool down and reset them disabling The device turns off or does not •... -
Page 14: Removal Of Used
Thanks re-use, material utilization or other forms of old appliances, you make an important contribution to protecting our environment. COMPANY DETAILS PH Powermat TMK Bijak Sp. General Partnership Ul. Defenders of the Gdansk Post 97 42-400 Zawiercie DECLARATION OF CONFORMITY... -
Page 15: Construction Scheme
SCHEME OF CONSTRUCTION...
Need help?
Do you have a question about the PM-500-SSTT and is the answer not in the manual?
Questions and answers