Related Manuals for Powermat PM-OPS-14
Summary of Contents for Powermat PM-OPS-14
-
Page 1: User Manual
USER MANUAL SPRAYER / COMBUSTION SPRAYER PM-OPS-14 / PM-OPS-20 / PM-OPS-26 ORIGINAL MANUAL... -
Page 2: Table Of Contents
TABLE OF CONTENTS USER MANUAL..........................1 WARNING / INFORMATION SYMBOLS ..................3 PURPOSE OF THE DEVICE ......................... 3 MAIN FEATURES OF THE DEVICE ........................ 3 TECHNICAL DATA ..........................4 ASSEMBLY ..............................4 Sprayer mode .......... -
Page 3: Warning / Information Symbols
WARNING / INFORMATION SYMBOLS Before using the device, carefully read the instruction manual and safety ATTENTION: recommendations. Keep the instructions. ATTENTION: The use of eye protection is recommended. ATTENTION: Hearing protection is recommended. ATTENTION: The use of a dust mask is recommended PURPOSE OF THE DEVICE Backpack petrol sprayer is a portable, flexible and highly effective tool for working in plant protection. -
Page 4: Technical Data
TECHNICAL DATA MODEL PM-OPS-14 PM-OPS-20 PM-OPS-26 ≥4m Liquids: ≥4m Liquids: ≥4m Liquids: PERFORMANCE Powder / Granulate: ≥ Powder / Granulate: ≥ Powder / Granulate: ≥ 6m SPRAY / SPRAY HORIZONTAL SPRAY RANGE ≥12m ≥12m ≥12m START manual manual manual 7,500 rpm... -
Page 5: Dusting (Spreading) Mode
Tank assembly. Remove the bottom cover of the tank and put on the pressure (spray) cover, which is connected to the rubber tube (don't forget to put on the rubber gasket). Connect the transparent rubber tube to the tank cover (Fig. 1a), in this way the turbine air will be forced into the tank, creating an overpressure that will displace the liquid from the tank through the exhaust hose. -
Page 6: Antistatic Installation
Antistatic installation Dedusting can cause electrostatic charge, it depends on such factors such as type of chemicals, air temperature, humidity. To prevent this from occurring, use the supplied ground wire. Insert one end of the hose into the blow-off pipe while the other end is touching the ground. Connect the other end with the conductive wire, then screw the conductive wire and the ground wire with screws to the pipe to be bent. -
Page 7: Starting A Cold Engine
Chemicals should not be in the tank for long periods as this can lead to it until the outlet is blocked. Keep the tank cover tight while spraying. After adding powdered chemicals, clean the tank mounting bolts, and then tighten the cover firmly. Starting a cold engine Fig. -
Page 8: Starting A Warm Engine
Open the fuel tap on the carburetor (Fig. 6) - 2 Set the choke lever (Fig. 6) - 1 in the upper position Set the dusting control lever (Fig. 6a) - 1 in the lowest position, and the engine throttle lever (Fig. 6a) - 2 slightly above the middle of the range, position 5 or 6. -
Page 9: Safety Rules
SAFETY RULES Please read the instructions carefully. Make sure you understand how to use the machine before starting work. Protective clothing Wear a brimmed hat Wear safety glasses Wear a protective mask Wear long gloves Wear a chemical protective jacket Wear shoes The following persons may not use the sprayer Mentally ill... -
Page 10: Solving Common Problems
Starting the engine Close the flow of chemicals It is impossible to stand in front of the nozzle SOLVING COMMON PROBLEMS Heavy engine starts or won't start. Check that the candle is working properly Cause Solution Problem No spark Water has entered the plug pipe. Electrode Dry the pipe A pipe of a candle Set candle spacing to... -
Page 11: Maintenance And Preparation For Longer Storage
The engine stops Cause Solution Problem Loose spark plug cable The fuel The engine cuts out suddenly Connect the cable securely has run out refuel The engine cuts out gradually Clogged carburetor Clean the carburetor Clogged fuel tank opening. Unplug fuel mixed with water Change fuel Spraying... -
Page 12: Disposal Of Used Devices
2. Thoroughly clean the sprayer tank and powder / granulate outlet after dusting 3. After work, loosen the tank cover 4. After cleaning the device, run the engine at low speed for 2-3 minutes Maintenance of the fuel system 1. Gasoline residues in the carburetor may adversely affect the operation of the fuel system and engine operation, after using the device for a week, drain all the gas from it. -
Page 13: Manufacturer's Data
MANUFACTURER'S DATA PH Powermat TMK Bijak Sp. Jawna Ul. Obrońców Poczty Gdańskiej 97 42-400 Zawiercie DECLARATION OF CONFORMITY... - Page 14 Scheme...
Need help?
Do you have a question about the PM-OPS-14 and is the answer not in the manual?
Questions and answers