Table of Contents Introduction Features Package Contents Specifications Operation Controls and Functions IR Remote IR Pin Definition EDID Management Video Wall Web GUI User Guide RS-232 Command Application Example Thank you for purchasing this product Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product.
Page 3
Registration Page Please Activate your warranty by registering our product through the link below - www.orei.com/register Technical Support Need Help? Our experienced Technical Support Team is here for you to answer your questions, give technical advice or help troubleshoot your project to get you installed on time and on budget.
Introduction The UHDS-404VW is a multi-purpose high-speed video processing system. It can be configured for 2 different output modes. It can perform as a 4×4 seamless matrix switcher, or as a 2×2, 4×1 or 1×4 video wall solution. It also features a web browser in- terface module for control and configuration of the matrix, when used stand-alone or with a third party control system.
Web interface module for control and configuration of Matrix Controlled by front panel buttons, IR Remote, RS-232 and TCP/IP 3rd party drivers available for all major household control brands Package Contents UHDS-404VW 1pcs Matrix IR Remote 1pcs 3pin-3.81mm Phoenix Connector (male) 1pcs 20-60KHz IR Wideband Receiver Cable (1.5m)
Operation Controls and Functions OUT 1 OUT 2 OUT 3 OUT 4 1 2 3 Name Function Description ▪ Short press this button to power on the device. Power button ▪ Long press this button for 1 second to enter the standby mode. The power LED will light up green when the product is powered on, POWER LED and red when the product is on standby.
IR Remote Power: Power on the Matrix or set it to standby mode. INFO: Press this button to display the serial port baud rate and IP address at the top right of the screen. (The information will disappear after 5 seconds.) INPUT 1/2/3/4: Select the signal input channel.
IR Pin Definition IR Receiver pin’s definition is as below: IR RECEIVER IR Signal Grounding Power 12V IR RECEIVER Note: When the angle between the IR receiver and the remote control is ± 45 °, the transmission distance is 0~5 meters; when the angle between the IR receiver and the remote control is ±...
EDID Management This Matrix has 12 factory defined EDID settings, 2 user-defined EDID modes and 4 copy EDID modes. You can select defined EDID mode or copy EDID mode to input port through RS-232 control or Web GUI. RS-232 control operation: Connect the Matrix to PC with a serial cable, then open a Se- rial Command tool on PC to send ASCII command “s edid in x from z!”...
Video Wall The matrix supports 10 categories of display modes as below: 1x2-2 2x1-2 Group 1 Group 2 Group 3 Group 4 Matrix Users can select display modes via IR remote, Web GUI or RS-232 commands. page 12...
Web GUI User Guide The Matrix can be controlled by Web GUI. The operation method is shown as below: Step 1: Get the current IP Address. The default IP address is 192.168.0.100. You can get the current Matrix IP address in two ways: The first way: You can get the IP address via remote controller.
Page 14
Web GUI User Guide Step 3: Input the current IP address of Matrix into your browser on the PC to enter Web GUI page. After entering the Web GUI page, there will be a Login page, as shown below: Select the Language from the drop-down list to choose English or Simple Chinese. Select the Username from the drop-down list and enter the password.
Page 15
Web GUI User Guide ■ Status Page The Status page provides basic information about the product model, installed firm- ware version and the network settings of the device. ■ Input Page page 15...
Page 16
Web GUI User Guide You can do the following operations on the Input page: ① Inputs: Input channel of the device. ② Active: It indicates whether the channel is connected to a signal source. When the input port is connected to the signal, it shows green, otherwise, it shows gray. ③...
Page 17
Web GUI User Guide ■ Output Page You can do the following operations on the Output page: ① Outputs: Output channel of the device. ② Cable: It indicates the connection status of output ports. When the output port is connected to the display, it shows green, otherwise, it shows gray. ③...
Page 18
Web GUI User Guide ■ Video Mode Page You can do the following operations on the Video page: ① Matrix: Click to select Matrix mode. ② Video Wall: Click to select any multiview display mode. ③ Matrix/Video Wall Adjustment: Display the input and output information. ④...
Page 19
Web GUI User Guide ■ Network Page You can do the following operations on the Network page: Modify Network Setting Modify the IP Mode Address/Gateway/Subnet Mask/Telnet Port as required, click “Save” to save the settings, then it will come into effect. After modification, if the Mode is “Static”, it will switch to the corresponding IP Address;...
Page 20
Web GUI User Guide Note: Input rules for changing passwords: (1) The password can’t be empty. (2) New Password can’t be the same as Old Password. (3) New Password and Confirm Password must be the same. Set the Default Network Click “Set Network Defaults”...
Page 21
Web GUI User Guide ■ System Page You can do the following operations on the System page: ① Panel Lock: Click to lock/unlock panel buttons. “ON” indicates that panel buttons are unavailable; “OFF” indicates panel buttons are available. ② Beep: Click to turn on/off the beep. ③...
RS-232 Command The product also supports RS-232 command control. Connect the RS-232 port of the product to a PC with a 3-pin phoenix connector cable and an RS-232 to USB cable. The connection method is as follows. Ground 3-pin Phoenix Connector RS-232 RS-232 to USB cable Then open a Serial Command tool on PC to send ASCII commands to control the...
Page 23
RS-232 Command ASCII Commands Serial port protocol: Baud rate: 115200(default) Data bits: 8 Stop bits: 1 Check bit: 0 x - Parameter 1; y - Parameter 2; ! - Delimiter Command Function Description Example Feedback Default Code System Setting help! Lists all commands help! get the unit all status:...
Page 24
RS-232 Command Command Function Description Example Feedback Default Code System Setting r lock! Get panel button lock state r lock! panel button lock on/off reboot… system initializing... s reboot! Reboot the device s reboot! initialization finished! mcu fw version x.xx.xx reset to factory defaults system initializing...
Page 25
RS-232 Command Command Function Description Example Feedback Default Code Output Setting Get output y resolu- tion(y=0~4) y=0. output all output 1 reso- s output 1 r output y res! y=1. output 1 lution: csc 1! y=2. output 2 3840x2160p60 y=3. output 3 y=4.
Page 26
RS-232 Command Command Function Description Example Feedback Default Code Output Setting Get output y hdcp status. (y=0~4) y=0. output all r output y r output 1 output 1 hdcp: y=1. output 1 hdcp! hdcp! hdcp 1.4 y=2. output 2 y=3. output 3 y=4.
Page 27
RS-232 Command Command Function Description Example Feedback Default Code Output Setting Set output y stream en- able/disable (y=0~4, x=0~1) y=0. output all s output y y=1. output 1 s output 1 output 1 stream: stream enable y=2. output 2 stream 1! enable y=3.
Page 28
RS-232 Command Command Function Description Example Feedback Default Code EDID Setting Set hdmi input x edid mode (x=0~4,z=1~18) x=0. all input x=1. input1 x=2. input2 x=3. input3 x=4. input4 z=1. 4k2k60_444,stereo audio 2.0 z=2. 4k2k60_444,dolby/dts 5.1 z=3. 4k2k60_444,hd audio 7.1 s edid in 1 input 2 edid:1080p, z=4.
Page 29
RS-232 Command Command Function Description Example Feedback Default Code Video Wall Setting Set tv wall display mode(x=1~10) x=1. 2x2 mode x=2. 2x1 mode x=3. 2x1-2 mode x=4. 1x2 mode tv wall mode: s tw mode x! s tw mode 1! tv wall mode: 2x2 x=5.
Page 30
RS-232 Command Command Function Description Example Feedback Default Code Video Wall Setting Set tv wall resolution (x=1~15) 1. 4096x2160p60, 2. 4096x2160p50, 3. 3840x2160p60, 4. 3840x2160p50, 5. 3840x2160p30, 6. 1920x1080p60, tv wall resolution: s tw res x! 7. 1920x1080p50, s tw res 3! 3840x2160p60 3840x2160p60 8.
Page 31
RS-232 Command Command Function Descrip- Example Feedback Default Code tion Network Setting set ip address: 192.168.0.100 (please use “s net reboot!” s ip addr Set network ip s ip addr command or repower device xxx.xxx.xxx. address 192.168.0.100! to apply new config!) xxx! dhcp on, device can’t config static address, set dhcp off first.
Application Example TV box or Blu-ray Player Power Supply INPUT OUTPUT TCP/IP RS-232 IR EXT HD 1 HD 2 HD 3 HD 4 HD 1 HD 2 HD 3 HD 4 DC 12V UHDTV 1 UHDTV 4 IR Receiver UHDTV 2 UHDTV 3 The terms HDMI and HDMI High-Definition Multimedia interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.