Related Manuals for AMS AS5013
Summary of Contents for AMS AS5013
- Page 1 User Manual – AS5013 Demo Kit AS5013 Two-dimensional Magnetic Position Sensor with Digital Coordinates output www.ams.com Revision 2.1 / 2013/01/08...
-
Page 2: Table Of Contents
AS5013 – Demo Kit User Manual Table of Contents General Description ....................... 2 Package and Board Description .................... 2 How to get the kit running ...................... 4 Schematics ..........................7 Layout ............................ 9 Ordering Information ......................10 Copyright ............................. 11 Disclaimer ........................... -
Page 3: General Description
AS5013 – Demo Kit User Manual 1. General Description The AS5013 is a complete Hall Sensor IC for smart navigation key applications to meet the low power requirements and host SW integration challenges for products suc h as cell phones and smart handheld devices. - Page 4 AS5013 – Demo Kit User Manual Figure 1: AS5013-DB-2 Demo board USB plug (to PC) EasyPoint Module Horizontal mode-, Hall Push-, Center- LED , , Vertical mode LED Direction Switch Joystick button EasyPoint™ module Moving the EasyPoint knob acts like an analog joystick, sending progressive XY coordinates to Windows via USB.
-
Page 5: How To Get The Kit Running
3. How to get the kit running First Steps 1. Install the Evaluation Software. The Evaluation Software is located on the USB Stick or can be downloaded from the ams homepage. For detailed instructions refer to the Evaluation Software Manual. www.ams.com Revision 2.1 / 08/01/13... - Page 6 HID game controller Demoboard modes The AS5013 Demoboard can be configured in different ways without any software. Mode 0: Without pressing any key, power up the demoboard with the USB cable. HID Joystick button I is controlled by the EP button (from the EasyPoint™ module) and ...
- Page 7 USB cable. All the LEDs are ON. The AS5013 is in “Bootloader mode”. This mode is used to update the firmware of the demo board if a new file is available on the ams website: Firmware update: To update the firmware, just open the AS501X Evaluation Software 4.1.6 or newer and connect...
-
Page 8: Schematics
VDDp) by this 3.3V supply. Connector J4 is used if an external MCU has to be connected to the AS5013 of the demo board, instead of the C8051F320. In that case, cut the PCB tracks (bottom side) to disconnect the N40P112 module from the MCU. - Page 9 All the switches (dome switch: Button EP, Button I, Button II, Button III) are connected directly to the microcontroller. The unique I²C serial bus (SCL, SDA) controlled by the C8051 microcontroller is used for the EasyPoint module (AS5013). The interrupt output INTn is connected directly to the MCU interrupt input. www.ams.com Revision 2.1 / 08/01/13...
-
Page 10: Layout
AS5013 – Demo Kit User Manual 5. Layout Figure 7: PCB Top and Bottom View PCB Top view PCB Bottom view www.ams.com Revision 2.1 / 08/01/13 page 9/12... -
Page 11: Ordering Information
AS5013 – Demo Kit User Manual 6. Ordering Information Table 2: Ordering Information Ordering Code Description comments AS5013-DB-2 AS5013 Demo Kit AS5013 Demo board in gamepad-shape www.ams.com Revision 2.1 / 08/01/13 page 10/12... -
Page 12: Copyright
No obligation or liability to recipient or any third party shall arise or flow out of ams AG rendering of technical or other services. - Page 13 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: AS5013-DB-2...
Need help?
Do you have a question about the AS5013 and is the answer not in the manual?
Questions and answers