8�5 Changing Flame Brightness; 8�6 Setting Open Window Detection Function; 8�7 Setting Timer; 8�8 Changing Between Fahrenheit And Celsius - Amazon B081236VRD Manual

EN
8.5 Changing flame brightness
» Press the flame brightness button (N) repeatedly until the desired
brightness level is selected�
» The display (H) shows the code F1 - F5 to indicate the
brightness level selected�
8.6 Setting open window detection function
The product monitors the temperature of the room once it reaches
the set temperature� When in open window detection mode, and if
the room temperature drops by 5°C or more within 10 minutes, the
product automatically stops heating to conserve energy�
1� Press and hold the flame brightness button (N) on the control
panel to activate this feature�
2� Quickly press the increase button (I) or decrease button (L) to
change the setting� The display shows E1 to indicate function is
on�
3� To deactivate this feature, repeat previous step until the display
shows E0 to indicate function is off�
E0: Open window detection function off
E1: Open window detection function on
8.7 Setting timer
1� Press the timer button (M) to activate timer function� The
TIMER/SET indicator starts flashing�

9. Changing the Battery

NOTICE
» Ensure that the batteries are installed correctly with regard to polarity (+ and -)�
» Clean the battery contacts and also those of the equipment prior to battery installation�
» Remove exhausted batteries promptly�
1� Remove the battery holder from the remote control�
2� Replace the used battery with a new CR2025 3 V battery� The positive pole (+) must be pointing upwards�

10. Cleaning and Maintenance

WARNING
Risk of electric shock!
» To prevent electric shock, set the on/off switch (C) to '0' and remove the plug (F) from the socket outlet�
10.1 Cleaning
NOTICE
Clean the product regularly to prevent the build-up of hairs dust or lint around the heating vents (G), as this may cause the
outlet to become blocked�
» To clean the product, wipe with a soft, slightly moist cloth�
» Never use corrosive detergents, wire brushes, abrasive scourers, metal or sharp utensils to clean the product�
» Do not spray liquids directly onto any surfaces of the product�
10.2 Plug fuse replacement (for UK only)
» Use a flat screwdriver to open the fuse compartment cover�
» Remove the fuse and replace with the same type (13 A, BS1362)� Refit the cover�
10.3 Maintenance
» Any other servicing than mentioned in this manual should be performed by a qualified service personnel�
8
3
2
1
2� Press the timer button (M) to skip through the days until you
reach the desired day for setting� Each day which does not
require timer function should be programmed as 00.00 for ON
and OFF time�
3� Once the desired day has been selected, press the increase
button (I) or decrease button (L) to set the ON hours� Press the
timer button (M) to continue�
4� Press the increase button (I) or decrease button (L) to set the
ON minutes� Press the timer button (M) to continue�
5� Press the increase button (I) or decrease button (L) to set the
OFF hours� Press the timer button (M) to continue�
6� Press the increase button (I) or decrease button (L) to set the
OFF minutes� Press the timer button (M) to continue�
7� Press the standby button (K) to exit timer setting function� The
TIMER indicator stays lit to indicate the timer is active�
NOTICE
To turn off timer function, press the timer button (M)
once, the TIMER/SET indicator flashes� Press the increase
button (I) or decrease button (L), until only SET indicator flashes,
then press the standby button (K)� The timer is now off�
8.8 Changing between Fahrenheit and Celsius
Press the Celsius/Fahrenheit button (O) to toggle between
temperature in Fahrenheit or Celsius�
4
5