Table of Contents
Advertisement
Available languages
Available languages
Cable Installation
To reduce the risk of injury, always
WARNING
wear proper eye protection marked
to comply with ANSI Z87.1. Always wear leather
gloves over latex/rubber gloves to avoid entangle-
ment. The cable is under pressure and can uncoil
unexpectedly. Cable tip may be sharp.
Remove the cable for cleaning after each use. Dif-
ferent size and types of cables are available for
different applications.
To remove the cable:
1. Remove the battery pack and set the front handle
to the feed position
tions in "Controlling the Cable".
2. Pull the cable out through the front handle until
the end of cable indicator is reached
NOTE: Cable will appear stuck once the end of cable
indicator is reached.
3. Set the front handle to the neutral position and pull
out the remaining cable.
To install the cable:
1. Remove the battery pack and set the front handle
to the locked position
tions in "Controlling the Cable".
2. Insert the back of the cable through the nose of
the tool until the cable catches.
3. Set the front handle to the feed position
continue feeding the cable through the front
handle.
4. Set the forward/reverse switch to reverse ◄.
5. Pull the trigger and push the cable into the drum.
This makes sure the cable is wound into the drum
correctly.
6. Push the remaining cable into the drum by hand.
7. Remove the protective tip cover from new cables
before use.
Cable Attachment Installation
To install the attachment:
Snap the attachment coupler into the cable coupler.
Test the cable before inserting into the drain to make
sure the attachment does not fall off during use.
To remove the attachment:
Insert the pin key into the coupling hole and pull at-
tachment off of cable.
according to the instruc-
according to the instruc-
WARNING
ries. Only use accessories specifically recom-
mended for this tool. Others may be hazardous.
To reduce the risk of short circuit, when setting
tool or battery down, do not allow battery to
contact corrosive or conductive fluid.
To reduce the risk of injury, always wear proper
eye protection marked to comply with ANSI Z87.1.
Always wear leather gloves over latex/rubber
gloves to avoid entanglement.
Using Forward/Reverse Switch
1. For forward (clockwise) rotation, push in the
.
forward/reverse switch from the right side of the
tool ►. Check the direction of rotation before use.
2. For reverse (counterclockwise) rotation, push in
the forward/reverse switch from the left side of the
tool ◄. Check direction of rotation before use.
3. To lock the trigger, push the forward/reverse
switch to the center position. The trigger will not
work while the forward/reverse switch is in the
center locked position. Always lock the trigger
or remove the battery pack before performing
maintenance, changing accessories, storing the
and
tool and any time the tool is not in use.
Starting, Stopping and Controlling Speed
This tool may be used at any speed from 0 RPM to
full speed.
1. To start the tool, pull the trigger. The trigger controls
the cable spin feed and cable feed speed.
2. To vary the driving speed, increase or decrease
pressure on the trigger. The further the trigger is
pulled, the greater the speed.
3. To stop the tool, release the trigger.
Controlling the Cable
1. To feed the cable, set the forward/reverse switch
to the forward position ►, and the front handle
to the feed position
the handle forward. To lock the front handle in
the feed position, twist the front handle a quarter
turn to the right.
NOTE: Varying the degree of turn provides ad-
ditional cable feed speed control. For fastest feed
speed, twist the front handle 90 degrees to the right.
CAUTION! Never twist front handle more than 90
degrees to the right and back. Turn by hand only.
2. To retract the cable, set the front handle to the
feed position
to the reverse position ◄.
3. To lock the cable, set the front handle to the locked
position
ing it a quarter turn to the right.
4. To put the cable into neutral position, set the front
handle to the center position, in between the feed
and locked positions.
5
OPERATION
Always remove battery pack before
changing or removing accesso-
by pushing and holding
and the forward/reverse switch
by pulling the handle back and twist-
Advertisement
Table of Contents
