Samsung SMH1611W/XAA Troubleshooting

Model: SMH1611*/XAA
SUPPORT INFORMATION
Training — Plus One http://my.plus1solutions.net/clientPortals/samsung/
Help — GSPN http://gspn3.samsungcsportal.com
Samsung Product Support TV
Customer information videos and chat programs. Programs for Fridges, Laundry, Ranges & D/W
Error Code
-SE-
Microwave cover assembly
The front of the top cover has flanges that must fit inside the front
frame and vent, and the bottom goes above the bottom cover. Start
with the left side and hold in place with one screw once engaged.
Leave the display loose so you can see that the right side is engaged
properly. Then mount display and the vent, ensuring the vent en-
gages the flange.
To Test Blower Windings:
3. Continuity test across the two wires of the run capacitor should be approximately 120 ohms of resistance. This test
allows you to read across all windings at the same time.
Oven Thermal Cutout
The oven thermal cutout (Cavity TCO) is located on the top side of the oven cavity beside the exhaust duct with a tem-
perature rating of 248°F (120°C) and is NOT resettable.
Hood Thermal Cutout
This cutout will protect the touch control from excessive heat by turning the vent fan on at low speed. If the surface units
of the range are used for long periods of time heat will build up and could damage the microwave control. In order to pre-
vent this, a thermal cutout is installed on the duct behind the control. This cutout will close (158°F/70°C - vent fan ener-
gized) and open (104°F/40°C - vent fan de-energized) depending on temperature.
Magnetron Thermal Cutout
The magnetron thermal cutout is located above the leads to the magnetrons. It is designed to prevent damage to the
magnetron if an overheated condition develops in the tube due to cooling fan failure, obstructed air ducts, dirty or
blocked air intake. Under normal operation, the magnetron thermal cutout remains closed. However, when abnormally
high temperatures are reached within the magnetron, the magnetron thermal cutout will open at 302°F (150°C) causing
the oven to shut down. After the temperature drops to 140°F (60°C) it will reset and cooking will be able to resume.
Bottom Thermal Cutout
During a fire on the stove the heat could be intense enough to close the Hood Thermal Cutout and force the fan to run.
While at moderate high temperature we do want it to run, however during a fire it is advantageous to NOT have the vent
fan running. So if a fire were to start on the stove top the Bottom Thermal Cutout would open at 248°F (120°C) and re-
move all power to the microwave oven. This cutout is NOT resettable.
SMH1611
IMPORTANT SAFETY NOTICE – "For Technicians Only" This service data sheet is
intended for use by persons having electrical, electronic, and mechanical experience
and knowledge at a level generally considered acceptable in the appliance repair trade.
Any attempt to repair a major appliance may result in personal injury and property
damage. The manufacturer or seller cannot be responsible, nor assume any liability for
injury or damage of any kind arising from the use of this data sheet.
http://support-us.samsung.com/spstv/howto.jsp
Cause and countermeasure
Key short error(10 sec.). Replace assy
control panel or smart board.
1. Disconnect power and remove grill. 2. Open control panel and discharge capacitor.
Fast Track Troubleshooting
Publication # rsSMH1611 Revision Date 1/19/2012
SE error. Switch membrane not
available. Order Control Panel.
Model name
SMH1611B/XAA
SMH1611W/XAA
SMH1611P/XAA
SMH1611S/XAA
2/17/2012
ASSY CONTROL PANEL
DE94-02411A
DE94-02411B
DE94-02411C
DE94-02411D
1