MIRABELLA Genio I003972 Manual

4m wi-fi led pixel neon light

Advertisement

I003972 Genio 4M Wi‐Fi LED Pixel Neon Light 
WARNING: 
LED NEON LIGHT CAN BE USED INDOOR OR OUTDOOR UNDER THE SHADE ONLY  
ADAPTOR/ TRANSFORMER AND Wi‐Fi CONTROLLER MUST REMAIN INDOOR AT ALL TIMES 
TO ENSURE THE SAFE AND SATISFACTORY OPERATION OF THIS SET PLEASE READ THESE INSTRUCTIONS CAREFULLY AND 
FOR ANY QUESTIONS OR TROUBLESHOOTING PLEASE VISIT www.mirabellagenio.com.au 
We recommend that the set be tested prior to being set up in the desired location   
SAFETY INFORMATION
• Remove set from the packaging before connecting to the power supply.   
• Before using or re‐using the set, inspect the set carefully   
• Use only with the adaptor/transformer supplied   
• Do not connect the set electrically to another set from a different manufacturer   
• Ensure that the cable is completely uncoiled whilst set is in use. Failure to do so may cause overheating   
• Avoid damage to wire insulation (cable), as this could cause a short‐circuit and damage the transformer
• Do not use any set which has been: cut, damaged, or has frayed wire insulation, loose connections or exposed wires 
 
Note: When connecting, please ensure the arrows are aligned with one another, otherwise it will NOT light up 
Neon light cannot be cut and join like the LED strip light.   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
RETAIN IT FOR FUTURE REFERENCE 
:   
 
 

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Genio I003972 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for MIRABELLA Genio I003972

  • Page 1 I003972 Genio 4M Wi‐Fi LED Pixel Neon Light  WARNING:   LED NEON LIGHT CAN BE USED INDOOR OR OUTDOOR UNDER THE SHADE ONLY    ADAPTOR/ TRANSFORMER AND Wi‐Fi CONTROLLER MUST REMAIN INDOOR AT ALL TIMES  TO ENSURE THE SAFE AND SATISFACTORY OPERATION OF THIS SET PLEASE READ THESE INSTRUCTIONS CAREFULLY AND  RETAIN IT FOR FUTURE REFERENCE  FOR ANY QUESTIONS OR TROUBLESHOOTING PLEASE VISIT www.mirabellagenio.com.au  We recommend that the set be tested prior to being set up in the desired location    :    SAFETY INFORMATION • Remove set from the packaging before connecting to the power supply.    • Before using or re‐using the set, inspect the set carefully    • Use only with the adaptor/transformer supplied    • Do not connect the set electrically to another set from a different manufacturer    • Ensure that the cable is completely uncoiled whilst set is in use. Failure to do so may cause overheating    • Avoid damage to wire insulation (cable), as this could cause a short‐circuit and damage the transformer     • Do not use any set which has been: cut, damaged, or has frayed wire insulation, loose connections or exposed wires    Note: When connecting, please ensure the arrows are aligned with one another, otherwise it will NOT light up  Neon light cannot be cut and join like the LED strip light.                   ...
  • Page 2 Fi for your router or check our website;s FAQ for some common router settings.      Install the APP and register Account    For the best experience, download the "Mirabella Genio" APP to your smartphone from the App Store or Google Play, the APP  icon will be displayed after it’s installed successfully  EZ method – when the light is fast blinking (2 blinks per second)      1. Connect the neon light to the adaptor then switch on the power, wait a few seconds, neon light will be blinking fast  If it did not automatically start to blink fast when first powered on, press and hold the pairing button on the Wi‐Fi  controller until the light starts to blink rapidly (2 blinks per second)     Open Mirabella Genio APP, tap on +,    add Manually then choose genio strip light from the list     Entre your 2.4Ghz Wi‐Fi name and password, (make sure Wi‐Fi name doesn’t end with ‐5G)                  Follow the APP instruction carefully to complete the network pairing process.      if the fast‐blinking method (EZ method, mentioned above) doesn’t work, please try the slow blinking (AP method) below.  While the strip light is rapidly blinking, press and hold the pairing button on the Wi‐Fi controller again and then wait for the  light to start  blinking slowly (1 blink per every 2 seconds)     ...
  • Page 3   open up the Mirabella genio APP, tap on + , add Manually then choose genio strip light from the list  1.    Entre your 2.4Ghz Wi‐Fi name and password, (make sure the Wi‐Fi name doesn’t end with ‐5G)  then in reset the device first screen tap on EZ mode in the Top right hand corner just below the battery image ,  select AP Mode (refer to the 1st and 2nd image below) Now Confirm indicator slowly blinking (refer to image 3),    hit Next, then Go to connect and connect to Wi‐Fi named SmartLife_XXXX      Note: If you fail to see Wi‐Fi name beginning with the word SmartLife_XXXX, then mean the device is  not slowly blinking, please reset and make it slowly blinking                       ...
  • Page 4     Should the transformer, supply plug or supply flexible cord get damaged, do not attempt to repair.            TO BE REPAIRED BY AN AUTHORIZED PERSON ONLY    THIS IS AN AUSTRALIAN STANDARDS REQUIREMENT IN THE INTEREST OF YOUR SAFETY·      FAQ:  Q. I have internet/power outage and the device went offline and doesn’t reconnect back online by itself?    A. Go the strip light co’ settings page (pencil icon), look for “remove device” Remove it and reset the device and pair it again  through the app.    Q. how do I control two or more neon lights at the same time?    A. Go the device’ settings page (pencil icon), look for the “create group” option,              If you are using Telstra/Optus NBN and you still having issue with pairing when use AP method, please call our tech  support line or check our online FAQ pages on how to disable the 5Ghz WiFi on the router setting  www.mirabellagenio.com.au/faqs   Mirabella International Pty Ltd    1 Mirabella Drive Tullamarine VIC. 3043 Australia  t: 1800 636 528  e: customerservice@mirabella.com.au       ...

Table of Contents