TABLE OF CONTENTS Safety First ..........................2 Product & Installation Overview ...................3 Suggested Tools and Supplies ....................4 Parts Included List ........................5 Parts Included Illustration .....................6 Base Assembly ........................7 Retrieval Chain Attachment - Mixer Side ................8 Swivel Leg Instructions ......................9 Cord Attachment - Mixer Side .....................10 Tank Penetration ........................11 Assembled Unit Installation ....................13 Mixer Maintenance Recommendations ................14...
Back to Contents SAFETY FIRST IMPORTANT: PLEASE READ THIS MANUAL AND SAVE FOR FUTURE REFERENCE WARNINGS: Moving Machinery Shock Hazard • Under NO circumstances should anyone enter the water with the mixer connected or in operation. • Running the unit out of water will create a dangerous situation and damage the seals. •...
Minimum Tank Hatch Width for RM-150 Installation Square Hatch Round Hatch 2 Legs Pivoted 17” 18” 1 Leg Pivoted 21” 22” No Legs Pivoted 24” 25” Some parts will arrive pre-assembled from Kasco; however, all assembly steps are listed for reference. RM-150 FLOOR MOUNT MANUAL...
Back to Contents SUGGESTED TOOLS AND SUPPLIES 1/2” socket Electric or cordless drill 3/8” drill bit wrench Half-round metal file Pan to catch shavings 1/8” Allen wrench 9mm wrench 7/16” wrench 1/2” wrench Side cutter Adjustable pliers Included supplies: • 1-3/8”...
Back to Contents PARTS INCLUDED LIST Assembly Item Description Qty Part No. Base CertiSafe™ mixer base pivoting leg 997260 5/16” serrated flange screw 566206 5/16” nylon locknut 566202 1/4” shoulder screw 451110 1/4” flat washer 566208 1/4” nylon locknut 566212 Retrieval Long retrieval chain - 50 ft.
Back to Contents BASE ASSEMBLY 1. Assemble the three mixer base legs loosely to each other using six 5/16” flanged screws (B) and 5/16” nylon locknuts (C). 2. Place the mixing unit upside down on the foam packing from the mixer unit box, if available. 3.
Back to Contents RETRIEVAL CHAIN ATTACHMENT - MIXER SIDE 1. Place the unit upright on the legs of the base assembly. 2. Insert each end link of the short retrieval chain (J) into a tab slot on the cage top ring. 3.
Back to Contents SWIVEL LEG INSTRUCTIONS 1. Remove cotter pin (Q) from leg assembly. 2. Pull the leg down until it moves freely from side to side. 3. Rotate leg to the left or right until it is positioned out of the way. 4.
Back to Contents CORD ATTACHMENT - MIXER SIDE 1. Use zip ties (P) to attach the power cable first to the cage and then to the long retrieval chain. Ensure there is enough gathered slack in the cable so that when the assembled unit is lowered into the tank, its weight is on the chain and not the cable.
Back to Contents TANK PENETRATION • The maximum tank roof thickness accommodated by the tank penetration parts included is 1-1/4”. • Suggested measurements are based on a 24” Ø 1-3/8” square access hatch. 1. Use the provided hole saw to drill a 1-3/8” clearance hole through the tank at a location conveniently Tank hatch center point reached from the tank hatch.
Page 13
Back to Contents TANK PENETRATION (CONT.) 7. Thread the cord grip (Y) onto the tank 8. Secure the top connecting link (H) to the relief penetration base. Leave cord grip loose. hanger. 9. Attach the cable support (AA) to the top connecting link and tighten the link.
Back to Contents ASSEMBLED UNIT INSTALLATION With the mount, retrieval chain, and cord affixed to the mixer and the tank roof penetration complete, the entire assembled unit is ready for installation. 1. As a precaution against dropping the chain, attach the last link of the long retrieval chain (G) to the top connecting link (H) prior to lowering the CertiSafe™...
• Replacing the seal and changing the oil every 3-5 years will add reliability and longevity to the mixer. • Seal replacement and all other repair services should be performed by Kasco Marine. Electrical Troubleshooting • If a unit fails to operate, you can use a series of simple checks to determine the general cause.
(for return delivery of the repaired unit), daytime phone number, and an e-mail address for correspondence regarding the warranty claim. Any expedited shipping method for the return of the unit is at the customer’s expense. Kasco Marine will return units repaired under warranty at our expense via ground freight within the continental United States.
This request should include a daytime phone number and e-mail address. Estimate options are as follows: • Kasco contacts the customer with a repair total after we evaluate the unit, but before we perform the work quoted. •...
Back to Contents REPAIR CONTACT FORM • Kasco requires that all equipment sent for repair MUST be accompanied by this form and marked to Repairs attention. Kasco Marine • Unit should be cleaned before shipping. 800 Deere Road • Kasco is NOT responsible for shipping damage accrued in Prescott, WI 54021 return shipment.