Kalorik BL 44440 - High-Powered Blender Manual

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed, including the following:

1. READ ALL INSTRUCTIONS BEFORE USE!
2. Check that the voltage in your home corresponds to that stated on the appliance.
3. To protect against electrical shock, fire or personal injury, do not immerse cord, plugs, or the base of the appliance in water or other liquid.
4. Do not use the appliance with wet hands. If the appliance is humid or wet, unplug it immediately.
5. Close supervision is necessary when any appliance is used by or near children. As a rule, this appliance is not intended to be used by children.
6. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
7. Unplug from outlet when not in use and before or during cleaning.
8. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Return the appliance to the nearest authorized service facility for examination, repair, or adjustment.
9. Keep your fingers away from moving parts or fitted tools. Do not place hands in the appliance while it is plugged in. Take special precautions when using this appliance, and do not leave unattended when plugged in.
10. The use of accessory attachments not recommended by the appliance manufacturer may cause injuries.
11. Do not use outdoors, household use only.
12. Do not let the cord hang over the edge of a table or counter or touch hot surfaces.
13. Do not place on or near a hot gas or electric burner, or in a heated oven. Do not place on a hot surface.
14. To disconnect, remove the plug from wall outlet by pulling on the plug, not the cord.
15. Do not use the appliance for anything other than intended use.
16. Do not place any of the following materials in the appliance: paper, cardboard, plastic, and the like.
17. Avoid contact with moving parts.
18. Never operate the appliance when the container is empty and do not attempt to remove the container from the base before the blades come to a complete stop. Keep lid on while in use and turn appliance off when adding food or liquids to the container.
19. Wait until moving parts stop running before you remove the lid of the machine. Do not remove container from its base until blades have come to a complete stop.
20. Do not exceed the maximum content indicated on the accessories.
21. Warning: misuse may cause serious injury. Care is needed when handling cutting blades, emptying the container and during cleaning.
22. Keep any utensils out of the container while blending to reduce the risk of damage to the blender and/or utensils. The blender should only be used with food and liquids. Use tamper if necessary, during blending process.
23. Do not place the appliance against a wall or against other appliances. Make sure surroundings are clear of any obstruction as the fans of the blender will emit air at high blending speeds.
24. When blending hot liquids, remove the clear plastic lid plug / measuring cup to allow steam to escape. Pay extreme caution to any escaping steam / hot liquids as they may cause burns and/or injury. Keep hands and face away from the hole in the lid to prevent scalding. Do not fill to more than the maximum hot liquid capacity (3 cups / 0.7 L).
25. If food gets clogged during blending process, use tamper to push down food. Do not attempt to place anything but food, liquids or the tamper inside the container while blender is on. If you are unable to properly unclog the appliance, turn appliance off and use tamper to redistribute food and liquids before resuming the blending process.
26. If appliance is running, only use tamper when the main lid is in place to avoid damaging it or the blades of the blender. Do not use any sharp or metal objects in the container as they may damage it. Use plastic or wooden spatulas if necessary. Never place anything but provided accessories inside the blender while it is on.
27. Always place the appliance on a horizontal, level, and stable surface.

OVERHEAT PROTECTION

• This appliance features a built-in overheat protection that monitors the temperature of the motor and signals incorrect operation. If the motor overheats, the device automatically turns off. If this occurs, turn the device "OFF" and unplug. Allow motor to cool down before plugging back in and resuming with blending operation.
• Frequent or multiple overheating may be the result of improper filling or use of the container. Attempt reducing the volume of solids or adding liquids to dilute. Do not overfill.

SAVE THESE INSTRUCTIONS HOUSEHOLD USE ONLY

POLARIZED PLUG INSTRUCTIONS

This appliance is equipped with a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug will fit into the polarized outlet only one way. If the plug does not properly fit into the outlet at first, reverse it. If it still does not fit, contact a competent qualified electrician. Do not attempt to modify the plug in any way.

SHORT CORD INSTRUCTIONS

A short power supply cord is provided to reduce the hazards resulting from becoming entangled in, or tripping over a longer cord. An extension cord may be used if care is exercised in its use.

• The electrical rating of the extension cord should be at least that of the appliance. If the electrical rating of the extension cord is too low, it could overheat and burn.
• The resulting extended cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over.

BEFORE THE FIRST USE

• Unpack the appliance and its accessories. Wash the accessories in hot, soapy water and then wipe them dry with a paper towel. Check that the blades and container are clean and dry.
• Position the blender on a flat and level surface.

OPERATING INSTRUCTIONS

1. Fit the container onto the motor unit. This unit is equipped with micro sensors which will only let the blender function if the jar is properly in place.
2. Prepare your food by cutting into small pieces, about 1x1 inch.
3. Add in the desired level of water or liquid into the container. Next, add desired food or ice, according to the recipe or preparation you are making. Pay attention that all food and liquids do not exceed the max line (8 cups / 2 L).
4. Fit the lid onto the container and make sure it is locked in position. It is important that the lid is properly secured to avoid any spilling or splatter.
5. If necessary, place the lid cap / measuring cup in the middle part of the lid.
6. Plug the appliance in. Follow instructions below for the various modes and functions you can use.

This blender has 1 main knob and 2 switches as well as three presets to choose from. An ON/OFF switch, a Pulse switch, a manual speed control dial, and "Ice – Smoothie – Soup" modes.

To turn on the blender, flip the ON/OFF switch to "ON". The blender is now ready for use in any function.
After use, flip the power switch to "OFF".
This blender will not work in any function unless this switch is turned on. You can also stop any functioning using this switch.

Speed controller

With the power switch flipped ON, turn the speed controller between its minimum and maximum level according to desired speed. It is generally recommended to start at slower speeds and gradually increase if using its maximum capacity.

Do not operate for more than 2 minutes at a time. Allow the motor to cool for 30 minutes before operating again.


The device can only be operated if the central dial is initially turned to position "OFF" and then turned to desired speed.

Mode function (M)

Turn power switch to ON position. Then, turn the center dial to "M". The buttons "Ice – Smoothies – Soup" will start blinking to indicate Mode function has been selected. This will also turn on "Pulse" function.

Press down on the button for the desired mode. The button will illuminate to indicate it has been selected. Press the same button again to stop the function. The buttons will start blinking again.

Pulse

Turn central dial to "M" mode. Press down to pulse. Press down in consecutively until desired consistency is reached.
NOTE: The pulse function should not be used continuously for more than 1 minute.

Ice function

The blender will start to pulse in repetition to crush ice. Keep mode selected until desired consistency has been reached.

NOTE: When crushing ice, ALWAYS add some liquid, as this will help the blending process. Fill the pitcher to about 2 cups with ice to allow room for the ice to move freely and achieve a more even consistency.

Smoothie function

The blender will start and gradually increase in speed automatically for a pre-set time. You may stop this function early or blend more in manual mode if desired consistency is not reached.

NOTE: If the system gets clogged while blending, use tamper to facilitate the blending process. You can also add more liquid if necessary.

Soup function

Your Kalorik blender will start automatically: Speed will increase until it reaches maximum speed and will stop by itself. The speed of the blades is enough to heat up cold liquids and foods, allowing for a soup preparation.

We suggest starting with cold or room temperature liquids to avoid going past the maximum limit on hot liquids and avoid excessive pressure build-up.

This function can raise the temperature of room-temperature ingredients by approximately 10-15°F per minute. A soup is generally considered ready once heavy steam issues from the hole in the lid, and that it reaches around 160°F.

Note: Temperature is for reference. Different foods and ingredients may heat up at different rates.

Always remove the lid cap / measuring cup from the main lid when using soup function and leave lid hole unobstructed.

Note: While using "SOUP" function, even though foods and liquids may be heated inside the container, it is preferable to pre-cook any foods (veggies, etc.) you wish to use.

SAFETY GUIDELINES WHEN BLENDING WITH HOT LIQUIDS

Be careful when adding and mixing hot ingredients or removing the lid from the Blender Jar. Steam might escape unexpectedly. ALWAYS remove lid cap to prevent pressure build-up.

Never use this device to process boiling liquids. Liquids must be below 115°F and container cannot exceed HOT LIQUIDS maximum (3 cups/ 0.7 L). Do not increase speed to more than the medium speed setting and do not let run for more than 4 minutes at a time.

Allow the appliance to cool down for 30 minutes before using it again in between two uses. Do not operate while empty.

To use the tamper, place long end in the middle hole of the lid while lid is securely placed on the container. Use it to press down food and bring it back into the blades' reach and aid with circulation. Do not place tamper in the blender for more than 30 consecutive seconds to avoid the blender overheating.

1. Never open the lid when blades are still rotating. For extra caution, you can unplug the appliance before any removal.
2. To add liquid ingredients during processing, remove the measuring cup of the lid and pour liquid through the opening. If the results are not satisfactory, switch the appliance off and stir the ingredients using the provided tamper. Tamper should only be used while appliance is running through the hole in the lid while lid is securely fastened on. Do not use tamper for more than 30 consecutive seconds.
3. This appliance can reach high rotation speeds* which may result in heat being produced by the appliance. This appliance is equipped with special fans to cool down the appliance and prevent overheating. Should overheating occur, unplug the appliance, and allow it to cool for a few minutes before trying to restart the blending process.

*26000 RPM +/-15% while empty

Tips & Tricks

• Try to maintain a one-to-one ratio of liquids to solids when blending frozen fruit. When blending fresh fruit and vegetables, use a 2:3 ratio of liquids to solids and gradually add liquid to achieve desired consistency.
• When blending hot foods, make sure that there is adequate steam release. Do NOT place under cabinets or place hands and face over appliance when using "SOUP" function. Do NOT place food or liquids hotter than 115°F into the container as the friction from the blades will increase the temperature as they blend.
• For best results, add liquids first, then powders, then solids, and then ice.
• If an air bubble occurs underneath the foods, simply use the provided tamper to get them within reach of the spinning blades. For thicker blending, such as for pastes or spreads, you can use the tamper to push the food "down" onto the blades. This will facilitate blending and provide a smoother consistency. Thicker mixtures work best when blended at a low to medium setting for a longer time, as this helps incorporate air into the mixture for a creamier result.
• When blending harder items such as nuts, pre-soaking will facilitate the blending process.
• Always start at a low speed and gradually increase for smoother consistency.

CLEANING AND MAINTENANCE

• Unplug the appliance before cleaning.
• Make sure to clean the appliance after each use. Clean the appliance before use if it has not been used in a while.
• Do not immerse the motor base in water. Clean the motor base with a wet cloth and dry with a dry paper towel or cloth.
• The blending container can be cleaned by filling it with soapy water about halfway and setting the blender on low speed, gradually increasing to max, and letting it run for 30 to 60 seconds. Turn appliance off and remove the container from its base and use a sponge or wet cloth to remove remaining food. Do not attempt to remove blades from the blender as this may cause injury and damage the blender. The blender jar is also dishwasher safe.
• All accessories and removable parts, except for the tamper tool, are dishwasher safe. To wash by hand, use warm, soapy water and rinse. Allow to air dry before storage.
• NEVER use abrasive cleansers as this may scratch the surface of the housing.
• Allow the parts to dry thoroughly before reassembling the device and/or storing. This helps to avoid mold or mildew buildup.

TROUBLESHOOTING