Table of Contents
Advertisement
Operating Instructions
Parts and their functions (continued)
11.
Service switches <SERVICE>
Perform switch settings before turning the unit on.
Service switches
SERVICE
LAN
LINK
ACT
1 - AUDIO INPUT - 2
12 V
IN
Function
SW1
Switches for initializing and initial settings
SW2
(Refer to the explanations in "Initialization 1",
SW3
"Initialization 2", "Direct start mode" )
SW4
Initialization 1
• Reset the user authentication settings and host authentication settings
for network connection.
(This will delete all the registered user information (IDs/passwords)
and host information (IP addresses).)
• With the service switches set as shown below, turn on the power of
the unit.
SW1
ON
OFF
<NOTE>
When initialization is complete, the status display lamp on the front of
the unit blinks green. Set the service switches back to their original
positions (SW1 to SW4 all OFF), then restart the unit.
Initialization 2
• The unit is reset to the state it was in at the time of purchase. (All
camera menu setting values and network setting values are reset.)
• With the service switches set as shown below, turn on the power of
the unit.
SW1
ON
OFF
<NOTE>
• When initialization is complete, the status display lamp on the front
of the unit blinks green. Set the service switches back to their original
positions (SW1 to SW4 all OFF), then restart the unit.
Direct start mode
• When the power of the unit is turned on, the pan‑tilt head (tilt) is not
returned to horizontal as part of the lens initializing operation. Use
when the tilt cannot be returned to horizontal, such as when the unit is
installed in a tight space.
SW1
SW2 SW3 SW4
ON
OFF
<NOTE>
• This may result in a slight change in tracking performance.
36
SFP+
12G SDI OUT
USB3.0 HOST
3G SDI OUT
G/L IN
RS-422
1
2/PM
SIGNAL
GND
Factory settings
OFF
OFF
OFF
OFF
SW2 SW3 SW4
SW2 SW3 SW4
12.
SFP connector <SFP+>
This is a connection terminal for an SFP+ optical fiber module. By
connecting the SFP+ optical fiber module, SMPTE ST2110
SDI signals are output as converted optical signals. Select the fiber
module that matches the signal bandwidth
1
A separate optional software key (AW‑SFU60) needs to be
*
purchased to enable SMPTE ST2110 functionality.
2
• 4K (59.94p, 50p): 12G
*
• 4K (other than 59.94p or 50p): 6G
• HD (59.94p, 50p): 3G
• HD (other than 59.94p or 50p): 1.5G
<NOTE>
• Optical signal input is not supported on this unit.
13.
12G SDI OUT connector <12G SDI OUT>
This is a 12G‑SDI video signal output connector.
14.
HDMI connector <HDMI>
This is the HDMI video output connector.
15.
USB3.0 HOST connector <USB3.0 HOST>
Video transmission using wireless connections is made possible by
connecting a 5G mobile router (one that supports USB tethering)
Use a product whose operation is guaranteed. For details, visit the
3
*
Panasonic website.
<NOTE>
• Refer to the catalog of the device you are using for usage times for
the 5G mobile router.
• Use a USB cable conforming to the USB3.0 specification. We also
recommend using a cable that is 1.5 m (4.9 ft) or shorter.
• Operation is not guaranteed with a cable for USB2.0. This unit will
need to be restarted if one is connected by mistake.
• A USB Type A – Type C adaptor may be required, depending on the
product to be connected.
16.
DC IN connector <12V
Input 12 V DC.
<NOTE>
• Use a DC cable with the following lengths.
For 12 V input: Max. 3 m (9.84 ft) (when using an AWG16 cable)
„ External DC power supply
Connect after making sure that the output voltage of the external DC
power supply is compatible with the rated voltage of the camera.
Select an output amperage for the external DC power supply with a
margin above the total amperage of the connected devices.
The total amperage of connected devices can be calculated with the
following formula.
Total power consumption ÷ voltage
When the power of the camera is turned on, inrush current is generated.
Insufficient power supply when turning on the power may cause a
malfunction. We recommend that you use an external DC power supply
that can assure double the capacity of the total power consumption of the
camera and connected devices that are turned on by interlock when the
power of the camera is turned on (such as lenses, wireless microphone
receivers).
• Make sure of the pin alignment of the DC output terminal of the
external DC power supply and the camera DC IN connector, and
connect the polarity correctly.
If the +12 V power supply is mistakenly connected to the GND terminal,
it may cause fire or malfunction.
12 V
1
GND
2
—
1
4
3
—
3
2
4
+12 V
1
or
*
2
for each format.
*
3
*
IN> (XLR connector)
IN
.
Advertisement
Table of Contents
