Table of Contents
Advertisement
Quick Links
SPARE PARTS DIAGRAM FOR
Direct Steam Kettle
KDT-1-T, KDT- 3-T, KDT-6-T, KDT-12-T
KDT-20-T, SD-450, SD-650, SD-760
SD-1050, SD-1200, SD-1600, SD-1800
SD-450-K6, SD-650-K12, SD-760-K12
SD-760-K20, SD-1050-K66, SD-1200-K612
SD-1600-K620, SD-1600-K1212
SD-1600-K1220, SD-1600-K2020
First Choice Group
Blakeney Way, Kingswood Lakeside
Cannock, Staffs, WS11 8LD
TEL: 01543 577778 FAX: 01543504141
Email: enquires@firstchoice-cs.co.uk
Web: www.firstchoice-cs.co.uk
Advertisement
Table of Contents
Related Manuals for First Choice CLEVELAND Welbilt KDT-1-T
Summary of Contents for First Choice CLEVELAND Welbilt KDT-1-T
- Page 1 KDT-1-T, KDT- 3-T, KDT-6-T, KDT-12-T KDT-20-T, SD-450, SD-650, SD-760 SD-1050, SD-1200, SD-1600, SD-1800 SD-450-K6, SD-650-K12, SD-760-K12 SD-760-K20, SD-1050-K66, SD-1200-K612 SD-1600-K620, SD-1600-K1212 SD-1600-K1220, SD-1600-K2020 First Choice Group Blakeney Way, Kingswood Lakeside Cannock, Staffs, WS11 8LD TEL: 01543 577778 FAX: 01543504141 Email: enquires@firstchoice-cs.co.uk Web: www.firstchoice-cs.co.uk...
- Page 2 Operators Manual Installation, Operation & Service Direct Steam Table Top Kettles Table-Top Direct Steam Kettles MODELS: KDT- 1 - T KDT- 3 - T KDT- 6 - T KDT-12 - T KDT-20 - T SD Stands MODELS: SD - 450 SD - 650 SD - 760 SD -1050...
- Page 3 For your safety DANGER Keep clear of pressure Keep hands away from relief discharge. moving parts and pinch points. IMPORTANT Do not fill kettle above Inspect unit daily for recommended level proper operation. marked on outside of kettle. CAUTION Surfaces may be Wear protective equipment extremely hot! Use when discharging hot product.
-
Page 4: Installation
INSTALLATION GENERAL Note: For SD Stands (with or without kettles) zero clearance is required on the sides and back. Installation of the unit must be accomplished by qualified installation personnel working to all applicable local and national codes. Improper KETTLES installation of product could cause injury or damage. - Page 5 STEAM CONDENSATE (Kettles c/w SD Stands) The stand comes factory plumbed so the condensate All steam plumbing to and from the kettle and is connected to the stands drain manifold. steam boiler should be thoroughly cleaned and inspected for dirt and debris before final POTABLE WATER connection to the kettle are made.
-
Page 6: Operation
OPERATING INSTRUCTIONS CLEVELAND STEAM COOKING EQUIPMENT IS INTENDED FOR COMMERCIAL USE ONLY BY PROFESSIONALLY TRAINED PERSONNEL. OPERATION FOR KETTLE/STEAMER COMBINATIONS: 1. Ensure that there is an adequate steam If the boiler in a steamer is supplying steam to a supply to the kettle. kettle, always heat the kettle first. -
Page 7: Cleaning Instructions
CLEANING INSTRUCTIONS CLEANING INSTRUCTIONS CAUTION 1. Turn unit off. SURFACES MAY 2. Remove drain screen (if applicable). Thoroughly BE EXTREMELY HOT! wash and rinse the screen either in a sink or a dishwasher. CARE AND CLEANING 3. Prepare a warm water and mild detergent solution in the unit. -
Page 8: Stainless Steel Equipment Care And Cleaning
STAINLESS STEEL EQUIPMENT CARE AND CLEANING (Suppied courtesy of Nafem. For more information visit their web site at www.nafem.org) Contrary to popular belief, stainless steels ARE susceptible to rusting. 4. Treat your water. Corrosion on metals is everywhere. It is recognized quickly on iron and Though this is not always practical, softening hard water can do much steel as unsightly yellow/orange rust. -
Page 9: Service Parts
SERVICE PARTS STEAM CONTROL ASSEMBLY... - Page 10 STEAM CONTROL ASSEMBLY ITEM NO. PART NO. DESCRIPTION QTY. FA11056 Binding Head Screw, 6-32 x 1/2" lg........4 KE50458 End Cap, condensate return .
-
Page 11: Plumbing Assembly
PLUMBING ASSEMBLY (for SD Stands) See Steam Control Drawing See Steam Control Drawing STEAM STEAM CONDENSATE CONDENSATE RETURN RETURN See Steam Control Drawing Steam In Configuration for SD Stand with Two Kettles STEAM STEAM... - Page 12 PLUMBING ASSEMBLY (for SD Stands) ITEM NO. PART NO. DESCRIPTION QTY. FI00169 Tee, 1/2" NPT. (single kettle units) ... . .1 (twin kettle units) ....3 KE54941-5 Safety Valve, 50 PSI, 1/2"...
- Page 13 CLEVELAND RANGE LTD. 8251 KEELE STREET, CONCORD, ONTARIO, CANADA...
- Page 14 CLEVELAND RANGE LTD. 8251 KEELE STREET, CONCORD, ONTARIO, CANADA...
- Page 15 FAUCET ASSEMBLIES...
- Page 16 STEAM CONTROL ASSEMBLY - FOR KETTLES WITH GEARBOX...
- Page 17 FAUCET ASSEMBLIES ITEM NO. PART NO. DESCRIPTION QTY. KE50825-8 6 gallon .........1 KE50825-1 12 gallon .
- Page 18 STEAM CONTROL ASSEMBLY - FOR KETTLES WITH GEARBOX ITEM NO. PART NO. DESCRIPTION QTY. KE52697 Lock Nut, 1/2" NPS ..........2 FA32500 Lockwasher .
- Page 19 TILTING GEARBOX ASSEMBLY - FOR KETTLES WITH GEARBOX...
- Page 20 TILTING GEARBOX ASSEMBLY - FOR KETTLES WITH GEARBOX ITEM NO. PART NO. DESCRIPTION QTY. 1.-16. KE02062-1 Tilting Gearbox Assembly ......... .1 KE02060 Gearbox Housing .
-
Page 21: Maintenance
MAINTENANCE ALL SERVICE MUST BE PERFORMED BY A QUALIFIED SERVICE TECHNICIAN. This kettle requires very little preventative maintenance other than daily cleaning. The pressure relief valve must be tested twice a year. PRESSURE RELIEF VALVE MARINE LOCK TESTING PROCEDURE Inspect lock at least twice yearly. 1. -
Page 22: Troubleshooting Guide
TROUBLESHOOTING GUIDE This section contains information intended for use by Authorized Service Personnel only. PROBLEM A/ Kettle heats too slowly or does not come to a boil. Probable Cause Remedy 1. Inadequate steam flow. Check for correct steam using chart below. If kettle is connected to a steamer and powered by a generator the units should be operated sequentially (kettle boiling first, then start steamer). -
Page 23: Specification Drawings
SPECIFICATION DRAWINGS KDT-1-T CLEARANCE REQUIREMENTS TO COMBUSTIBLE AND NONCOMBUSTIBLE SURFACES: Right - 4" Left - 0 Back - 0 8.00" 203mm 9.38" 238mm 12.25" 311mm 9.88" 251mm 3.50" 89mm 12.50" 318mm 9.31" 236mm 1.56" 40mm 1/2" NPT 1/2" NPT 8.13" CONDENSATE STEAM 207mm... - Page 24 KDT-3-T & KDT-6-T CLEARANCE REQUIREMENTS TO COMBUSTIBLE AND NONCOMBUSTIBLE SURFACES: Right - 4" Left - 4" Back - 1" WALL 1.00" 25mm STEAM CONTROL VALVE 2.25" 57mm 1.25"/32mm 1/2" NPT CONDENSATE 1/2" NPT RETURN STEAM INLET NOTE: INLET AND RETURN NOT INTERCHANGABLE GAL.
- Page 25 KDT-12-T & KDT-20-T CLEARANCE REQUIREMENTS TO COMBUSTIBLE AND NONCOMBUSTIBLE SURFACES: Right - 4" Left - 4" Back - 1.75" WALL 1.75" 45mm STEAM CONTROL VALVE MARINE LOCK 2.25" 57mm 1.25" 32mm 1/2" NPT CONDENSATE 1/2" NPT RETURN STEAM INLET NOTE: INLET AND RETURN NOT INTERCHANGABLE GAL.
- Page 26 SD STANDS WITH MODEL 17.70 4.00 10.00 KETTLES SD -450 - K 6 25.56 4.00 13.75 CLEARANCE REQUIREMENTS TO SD -650 - K12 COMBUSTIBLE AND 29.94 5.22 15.00 SD -760 - K12 NONCOMBUSTIBLE SURFACES: 29.94 3.10 15.00 Right - 0 Left - 0 Back - 0 SD -760 - K20...