Related Manuals for CreativeStar JXG 213-F
Summary of Contents for CreativeStar JXG 213-F
- Page 1 JXG 213-F DIY Instruction Manual V1.0.1 CREATIVESTAR SOLUTIONS 1601 Trapelo Road, STE 264 Waltham, MA 02451...
-
Page 2: Table Of Contents
Table of Contents Artemis Kiosk Installation Overview ........... 3 Preparations Before Assembly ............5 Required Tools ................. 5 Items Included in Kit ................ 5 Wire Building Instructions ..............5 Required Tools ................. 5 Required Parts ................. 5 Instructions ..................6 Bracket Building Instructions .............. -
Page 3: Artemis Kiosk Installation Overview
Artemis Kiosk Installation Overview Step 1: Lay out all items according to picture below to account for all pieces 1. Kiosk Stand 2. Kiosk Power Cable 3. Power Supply 4. 20 Pin Connector 5. Tablet Power 6. Relay Cable 7. Power Adapter 8. - Page 4 Step 2: It is highly recommended by the manufacturers to watch the video tutorial before beginning installation process. www.cssinco.com/manuals www.cssinco.com/videos Step 3: Start installation process following steps below and revisit video tutorial when necessary. Step 4: Double check functionality of terminal by going through the verification process: 1.
-
Page 5: Preparations Before Assembly
Preparations Before Assembly Required Tools • Phillips screwdriver • 2.0 mm flathead screwdriver • Scissors Items Included in Kit Please refer to page 3 Artemis Kiosk Installation Overview Wire Building Instructions Required Tools • 2.0 mm flathead screwdriver • Scissors Required Parts •... -
Page 6: Instructions
Instructions 1. Unwrap the temperature detection module (8) and strip the wire protector off the red and the black wire. 2. Take the tablet power cable (5) and strip the wire protector off both the red and black wires. 3. Fan out all the wiring as shown in the image below. 4. - Page 7 7. Tighten the screws so that the wire stays in place. 8. Go back to the temperature detection module (8) and gently remove the wire covers off the brown and blue wires. 9. Take the 20-pin connector (4) and gently remove the wire coverings off ONLY the purple and orange wire.
-
Page 8: Bracket Building Instructions
Bracket Building Instructions Required Tools: • Phillips Screwdriver Required Parts: • Extended Bracket (10) • Access Terminal Tablet Bracket (11) • Digital Detection Module Bracket (12) • Extended Bracket Cover (13) • Wall Mounting Kit (15) • Digital Detection Module Screws (16) •... - Page 9 2. Use the screws from the bracket screws and wingnuts (18) and place them through the previously outlined hole in red. Use the wingnuts to fasten the brackets. 3. After combining the brackets, slide the access terminal tablet (22) into bracket clips. Make sure the clips slide into the access terminal tablet (22).
-
Page 10: Stand Building Instructions
Stand Building Instructions Required Tools: • Phillips Screwdriver • Pliers Required Parts: • Kiosk Stand (1) • Kiosk Power Cable (2) • Power Supply (3) • Kiosk Base (9) Instructions: 1. Unscrew the two screws located on the back of the kiosk stand(1). 2. - Page 11 Congratulations on completing the DIY manual, to finish the product please refer to the JXG 213-F Prebuilt Assembly Manual.
-
Page 12: About Us
About Us Who we are CreativeStar Solutions is a Massachusetts based technology and software company providing essential technology, software, and services for businesses to adapt to the challenges brought on by the COVID-19 Pandemic. Not only does our technology and software help businesses reopen, but these products are also designed to prepare businesses for any unexpected events in the future.
Need help?
Do you have a question about the JXG 213-F and is the answer not in the manual?
Questions and answers