Page 1
C P - R 3 0 R R O T A R Y L A S E R I N S T R U C T I O N M A N U A L...
Page 2
Safety Read the following safety instructions • Tool service must be performed only by qualified before attempting to operate this product. repair personnel. Repairs, service or maintenance performed by unqualified personnel will void the Keep these instructions in a safe place or store warranty.
Page 3
S af e t y (continued) • Turn the laser off when it is not in use. Leaving CAUTION! the laser on increases the risk of staring into the Class 2 Laser Product. laser beam. • Do not operate the laser around children or allow • Never look into the laser beam directly children to operate the laser.
Item Checklist Please ensure the following items are included with your optical level. If anything is missing please contact your retailer. INCHES Centre Point Remote control Detector & clamp Laser target Laser glasses CP-R30R Charger Rechargeable battery 1x 9v alkaline...
Page 5
Laser Overview: Front Protective lighthouse Rotating laser port Control panel Charging port...
Page 6
Laser Overview: Base Charging port 5/8” x 11 thread for horizontal operation on a tripod Battery thumb screw...
Page 7
Laser Overview: Control Panel Counter clockwise rotation Grade adjustment Scanning mode SC AN Grade adjustment Grade adjustment Clockwise rotation Speed control Tilt alarm indicator Tilt alarm Manual / automatic mode Power Power indicator Manual / automatic mode indicator...
Page 8
Remote Control Overview: Front Button indicator Speed control Scanning mode Manual / automatic mode Counter clockwise rotation Clockwise rotation Grade adjustment Grade adjustment Grade adjustment Grade adjustment...
Page 9
Remote Control Overview: Back Battery compartment...
Page 10
Detector Overview: Front LCD display screen Sound on / off Laser sensor Coarse / fine detection Power Speaker...
Using Your Laser POWER SUPPLY Indoor charger • The indoor charger is for indoor use only. Rechargeable battery pack • Do not store in locations where moisture can be • The instrument is supplied with a rechargeable present or where the chargers could be exposed Ni-MH battery pack that is located in the base of to extreme temperatures.
Page 14
Using Your Laser (continued) Charging the rechargeable battery pack • Insert the charger into one of the two charging ports. The charging ports are located on the battery pack and underneath the control panel. Progress will be shown by the power indicator display on the charger as below: Red (flashing) = Charger and battery are not connected.
Page 15
Using Your Laser (continued) Removing and inserting the rechargeable battery pack • Loosen the battery thumb screw on the base of the instrument and remove the battery pack. • Insert the battery pack, ensuring the metal pins are aligned. Tighten the battery thumb screw. WARNING: Do not attempt to disassemble the battery pack.
Page 16
Using Your Laser (continued) HORIZONTAL MEASUREMENT SET UP Mounting to a construction tripod The construction tripod is an optional Level surface set up accessory which can be purchased • Select a place as close and practical to the work from your retailer. site as possible, and ensure that the location is clear of traffic.
Page 18
Using Your Laser (continued) OPERATION Speed control • Press the speed control button to cycle through Powering on various rotational speeds. • Press the power button once and the instrument • The speed control indicator will flash slowly when will power on and begin automatically self- speed is slow and fast when speed is increased.
Page 19
Using Your Laser (continued) Setting up a grade / slope Rotation direction • Whilst the instrument is in scanning mode press • To create a slope / grade, enter into manual mode by pressing the manual / automatic mode button the clockwise or counter clockwise button to on either the instrument or remote control.
Using Your Remote POWER SUPPLY OPERATION • The remote is powered by two AAA alkaline • Ensure the instrument is turned on and the laser batteries. head is rotating. • Press the speed control button to increase or Battery replacement decrease the speed of the laser head rotation.
Using Your Detector POWER SUPPLY MOUNTING THE STAFF CLAMP • The detector is powered by a 9V alkaline battery. • Insert the staff clamp screw into the staff clamp thread. • Rotate the nut until the clamp is secured in place. Battery replacement • Remove the battery door cover.
Page 22
Using Your Detector (continued) OPERATION • Switch the detector on by pressing the power button. The speaker will beep once indicating the instrument is operating. • The LCD screen will display the battery level, detection mode and speaker function. • To change between coarse and fine mode press Detector position for horizontal beams the coarse / fine mode button • Hold the detector upright and move into the path...
Checking Calibration Before doing any precision levelling it is advised to check the calibration of the instrument. • Set up the laser on a tripod at about 30m facing a • Detect and note laser position on the wall or staff. wall or staff with a detector.
Trouble Shooting Error Cause & Solution • Check the batteries. They may be in the wrong way or need replacing. Laser does • Check the battery compartment for signs of damage. Ensure they are clean and not bent. not turn on • Connect the mains power adaptor.
Care & Maintenance • This is a precision measuring instrument • Clean the instrument with a dry, soft cloth and should always be handled with care and after use in dusty, damp or wet conditions transported within the carry case provided. before storing.
Warranty 3 YEAR STANDARD WARRANTY PERIOD 7 YEAR EXTENDED WARRANTY PERIOD 1. The warranty period for your Centre Point tool is 3 1. The extended warranty is available on selected years from the date of purchase. tools only. 2. The warranty period for batteries, battery packs 2.
Page 27
Warranty (continued) AUSTRAL IA NEW ZE ALAND “Our goods come with guarantees that cannot be For more information please visit excluded under the Australian Consumer Law. You consumerprotection.govt.nz are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
Customer Support To assist you with any queries or technical questions please contact customer support Australia: 1300 658 338 New Zealand: 0800 367 527 United Kingdom: 0808 189 1152...
Specifications Specifications Centre Point CP-R30R Product code 400010 Warranty 7 Years* Accuracy ±1.5mm at 30m Operating range 500m (diameter) Levelling range ±9% / ±5° Laser class 2 Red Battery life 20 hours IP rating Weight (kg) 2.00 Dimensions (mm) 200 x 200 x 150...