Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Nordic CHS-L0218
Summary of Contents for Nordic CHS-L0218
- Page 1 18V CORDLESS CHAINSAW OPERATING MANUAL CHS-L0218...
-
Page 2: Product Specification
NORDIC PLEASE READ THIS MANUAL BEFORE OPERATION TO PREVENT RISK OF INJURY OR IMPROPER USE. PLEASE NOTE IMAGES IN THIS MODEL REFLECT A SIMILAR CHAINSAW AND NOT THE FINAL PRODUCT SOME SLIGHT VARIATIONS IN DESIGN MAY OCCUR. PRODUCT SPECIFICATION... -
Page 3: Electrical Safety
NORDIC 2.2 ELECTRICAL SAFETY • Always check that the power supply corresponds to the voltage on the rating plate. • Power tool plugs must match the outlet. Never modify the plug in any way. Do not use adapter plugs with earthed power tools. - Page 4 NORDIC must be repaired. • Disconnect the plug from the power source before making adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. • Store power tools, when not in use, out of the reach of children and do not allow people who are not familiar with the power tool or these instructions to operate it.
- Page 5 NORDIC • When cutting a limb that is under tension be alert for spring back. When the tension in the wood fibers is released the spring loaded limb may strike the operator and/or throw the chain saw out of control.
-
Page 6: Important Safety
NORDIC and should be have the initial practice cutting logs on a saw horse or cradle. • In the interest of personal safety it is highly recommended: when using the chain saw always use it with a residual current device (RCD) with a tripping current of 30 mA or less. -
Page 7: Intended Use
NORDIC • Under extreme conditions, battery leakage may occur. When you notice liquid on the battery, proceed as follows: • Carefully wipe the liquid off using a cloth. Avoid skin contact. • In case of skin or eye contact, follow the instructions below: 1. -
Page 8: Battery Charger
NORDIC Read manual before use Wear eye protection Wear ear protection Wear safety gloves In accordance with essential requirements of the European directive(s) Class II - The machine is double insulated; Earthing wire is therefore not necessary (only for charger) Ambient temperature 40°C max. -
Page 9: Charging The Battery
NORDIC the battery pack from the tool when convenient for you and your job. You can “top-off” your battery pack’s charge before starting a big job or long period of use. Due to lithium-ion’s fade-free properties, the only time it is necessary to charge the lithium-ion battery pack is when the pack has reached the end of its charge. - Page 10 Be sure to read the following information before you put the cordless equipment into operation: • Charge the battery pack with the charger. An empty battery pack requires a charging period of approximately 0.5 to 1 hour. NORDIC Chain saw assembly Note: After unpacking, check the contents for completeness and possible transport damage.
- Page 11 The saw chain must not sag, although it should be possible to pull it 1-2 millimetres away from adjusted if necessary. To do so switch the devic the guide bar in the centre of the guide bar. NORDIC 3.Place the guide bar with the elongated hole on the stud bolt and guide bolt on the chainsaw. brake.
-
Page 12: Chain Lubrication
NORDIC trigged automatically through the contact of the hand guard with the left hand. Therefore, always hold the chainsaw tight in both hands. MANUAL ACTIVATION OF THE CHAIN BRAKE Tilt the hand guard in the direction of the guide bar tip. -
Page 13: Switching On The Device
NORDIC • Start the device (see section “Switching on and off”). • Hold the running saw chain approx. 15 cm above a suitable surface for a short time. With sufficient chain lubrication, a light track will appear due to the oil sprayed from the saw chain. -
Page 14: After Use
NORDIC • Check for any leaks. HOLDING THE DEVICE CORRECTLY Risk of injury! • Never work on unstable ground! • Never work above shoulder height! • Never work when standing on ladders! • Do not bend too far when working! •... -
Page 15: Felling A Tree
NORDIC protected, allow the battery cool down for half an hour and it would recovery function. BASIC WORKING TECHNIQUE Risk of injury! This section examines the basic working technique for using the device. The information provided here does not replace the many years of training and experience of a specialist. Avoid any... -
Page 16: Removing Branches
If the guide bar tilts, the device may be jerked towards the user balance the backward force of the saw chain with their body stre of the guide bar will remain in contact with the wood and kickba NORDIC Risk of death or serious injuries! Felling a tree •... -
Page 17: Cleaning And Maintenance Overview
Original Instructions NORDIC bottom to top , and then saw through from the top. With branches that are supported or strained, the saw chain can wedge in the wood! Risk of injury! CLEANING AND MAINTENANCE Do not saw trunks that are strained! Splitting wood or a tilted ... -
Page 18: Sharpening The Saw Chain
NORDIC • Tighten the hand wheel for fastening the rail and chain cover. NOTE: The tension of a new chain must be checked after a few minutes in operation, and adjusted if necessary. Apply the chain brake. CLEANING THE GUIDE BAR OIL GUIDE GROOVE •... -
Page 19: Disposal And Recycling
NORDIC DISPOSAL AND RECYCLING The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. - Page 20 NORDIC Rear handle Hand guard/chain brake PLEASE NOTE: Battery & Charger sold separately. ON/OFF switch Front handle Saw Chain Chain tensioning wheel Guide bar...
Need help?
Do you have a question about the CHS-L0218 and is the answer not in the manual?
Questions and answers