Subscribe to Our Youtube Channel
Related Manuals for Flextool Mikasa MTX-85DYC
Summary of Contents for Flextool Mikasa MTX-85DYC
- Page 1 OPERATING INSTRUCTIONS MIKASA TAMPING RAMMER MTX-85DYC Version 2.0 (March 2022) FOR MORE INFORMATION EXCLUSIVE TO CONTACT US ON 1300 353 986 OR VISIT flextool.com.au...
- Page 2 TAMPING RAMMER MTX-85DY INSTRUCTION MANUAL We thank you for selecting Mikasa Tamping Rammer. For your safe and proper operation,please read this manual and be always sure to keep it ready for reference. 302-06401 http://www.mikasas.com *302-06401*...
- Page 3 Table of contents INTRODUCTION ..................APPLICATION, STRUCTURE AND POWER TRANSMISSION ....WARNING SIGNS ..................CAUTIONS FOR SAFETY................ General Cautions Precautions When Adding Fuel Precautions About Where To Use The Machine Precautions Before Starting Work Precautions While Lifting Transportation And Storage Precautions Maintenance Precautions Label Position Label List...
- Page 4 1．INTRODUCTION This instruction manual describes the proper methods for using the tamping rammer, as well as simple checks and ● maintenance. Be sure to read this instruction manual before using the rammer, in order to get full use of the excellent performance of this machine, to improve your operation and to perform work effectively.
-
Page 5: Warning Signs
3．WARNING SIGNS The triangle shaped marks used in this manual and on the decals stuck on the machine indicate common hazards. Be sure to read and observe the cautions described. Warning labels indicating hazards to humans and to equipment. ！ Denotes an extreme hazard. - Page 6 4.2 Precautions When Adding Fuel DANGER ！ When adding fuel. ■ Be sure to work in a well ventilated location. Be sure to work in a clear and flat location without any combustibles nearby. Be sure to stop the engine and wait until it has cooled down. Do not use any flames (smoking and etc.) while adding fuel.
- Page 7 DANGER ！ ■ Take the utmost care not to fall over the rammer during work, stored or stopped. Tie down the rammer with cable (wire or rope) when stopped or stored so that it cannot fall. ■ If the rammer falls over when children are nearby, they may have a seri- ous accident.
- Page 8 4.7 Maintenance Precautions WARNING ！ ■ Ensure safety for maintenance. It needs appropriate maintenance for keeping the machine performance. Keep the machine in good condition with attention to the machine’s condition always. CAUTION ！ ■ Be sure to stop the engine before maintenance of the machine. ■...
-
Page 9: Left Side View
FRONT VIEW LEFT SIDE VIEW TOP VIEW cleaner 4.9 Label List LABEL PART No. PART NAME Q’ TY REMARK 9202-21980 PLATE, SERIAL NO./MTX-85DY NPA-2198 9202-10870 DECAL,CAUTION/CONBI PL4 NPA-1087 9202-10100 DECAL,EC NOISE REQ.LWA108 NPA-1010 DECAL,LEVER OPERATION 9202-11690 NPA-1169 9209-00100 DEAL,CAUTION ICONS / MT NPA-1470 DECAL,FUEL CAUTION 9209-00100... - Page 10 4.10 Descriptions Of The Symbols On The Warning Decals Part code No.9209-00100 DECAL, SET /MT /EXP, EU ① ② NPA-1470 ⑧ ⑨ ③ ④ ⑤ NO USE ⑩ NPA-1471 ⑦ ⑥ NPA-1474 ⑪ NPA-1472 NO USE NPA-1473 Part code No.9202-10870 DECAL, COUTION/CONBI PL4 ⑧...
-
Page 11: Specifications
5．SPECIFICATIONS 5.1 Body Model MTX-85DY Dimensions Overall height 1063 Overall width Overall length Plate Size Length Width Fuel Tank Capacity Main Body Oil API Service Categories SE or higher SAE 10W-30 Oil Capacity Number of Blow Hz/v.p.m 10.9～11.6/656～698 Impact Force kN/kgf 15.7/1,600 Jumping Stroke... - Page 12 6．APPEARANCE 6.1 Appearance Dimensions ※ ...
- Page 13 6.2 Control Unit Positions And Names ONE POINT LIFTING HOOK AIR CLERNER COVER HANDLE ASSY BELLOWS FOOT ASSY FUEL TANK ASSY FUEL TANK MUFFLER ENGINE CAP ASSY ASSY ASSY THROTTLE LEVER ASSY OIL INLET RECOIL PLUG STARTER OIL GAUGE FOOT PLATE DRAIN PLUG...
-
Page 14: Inspection Before Operation
7．INSPECTION BEFORE OPERATION WARNING ！ Check the machine while the engine is stopped. You may be caught in a rotating ● part and be seriously injured. Check the machine after it has cooled down. Since the muffler is very hot, you may ●... -
Page 15: Operation
8．OPERATION 8.1 Starting Move the throttle lever to idle position. (Fig.4) Slowly return the recoil starter handle to the original position. After starting engine, warm up it for about five minutes by idling speed and check for fuel Idling position leakage or abnormal sounds in the meantime. Stop position CAUTION ！... -
Page 16: Stopping The Machine
9．STOPPING THE MACHINE Move the throttle lever quickly from the operation position to idling position. Idling position Run the engine at idling speed for five minutes for cool down for maximum engine life. Stop position Move the throttle lever quickly from the idling position to stop position. -
Page 17: Periodic Checks And Adjustments
12．PERIODIC CHECKS AND ADJUSTMENTS Check the machine while the engine is stopped. You may be caught in a WARNING ● ！ rotating part and be seriously injured. Check the machine after it has cooled down. Since the muffler is very hot, you may be ●... - Page 18 ● Change the main body oil. Remove the drain plug on the foot plate (Fig. 11) and drain the oil. Refill with approximately 820 cc of engine oil of API service categories SE or higher, SAE 10W-30. The oil level should be the halfway point of the oil gauge.
-
Page 19: Trauble Shooting
Replace it every 1000 hours of operation. Please refer to the engine operation manual for details of cleaning the oil filter of engine. Checking Fuel line Check the fuel line for damage or looseness. Replace it every 2 years, even if it does not show any abnormality. - Page 20 MIKASA SANGYO CO., LTD. 1-4-3,Kanda-Sarugakucho,Chiyoda-ku,Tokyo,101-0064,Japan PRINTED IN JAPAN...
- Page 21 Design and technical specifications may be subject to changes. © This publication is copyright. All rights are reserved. Flextool is a registered trade mark of Parchem Construction Supplies Pty Ltd. Mikasa is a registered trade mark of Mikasa Sangyo Co. Ltd, used under licence.
Need help?
Do you have a question about the Mikasa MTX-85DYC and is the answer not in the manual?
Questions and answers