Page 1
All manuals and user guides at all-guidesbox.com FILE NO. 040-200313 SERVICE MANUAL COLOUR TELEVISION VR9PJ Chassis 43VR9UM 50VR9UM Jul., 2003...
All manuals and user guides at all-guidesbox.com TABLE OF CONTENTS CHAPTER 1 GENERAL ADJUSTMENTS SAFETY INSTRUCTIONS ............................... 3 CRT ASSEMBLY REPLACEMENT AND MOUNTING ....................4 PICTURE TUBE COMPONENTS ADJUSTMENT ......................6 SERVICE POSITION ............................... 9 SERVICE MODE ................................10 DESIGN MODE ................................13 ELECTRICAL ADJUSTMENT ............................
All manuals and user guides at all-guidesbox.com CHAPTER 1 GENERAL ADJUSTMENTS SAFETY INSTRUCTIONS WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU- TION” AND “PRODUCT SAFETY NOTICE” INSTRUCTIONS BELOW. X-RAY RADIATION PRECAUTION 1. Excessive high voltage can produce potentially hazard- 2.
All manuals and user guides at all-guidesbox.com CRT ASSEMBLY REPLACEMENT AND MOUNTING CAUTION : DO NOT LOOSEN THE HEX HEAD BOLTS WITH SPRINGS (12 PCS), BECAUSE THOSE ARE FOR SEALING OF CRT COOLANT. Attention Serviceman The Hex Head Bolts with Springs.
Page 5
All manuals and user guides at all-guidesbox.com TO REMOVE CRT (Same procedure for R, G, B) 1. Remove CRT DRIVE Board, S. V. M. COIL and DEF. YOKE from CRT. 2. Remove Lens Assembly. 3. Detach CRT Anode Cap from CRT. Anode Cap 4.
All manuals and user guides at all-guidesbox.com WARNING : BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY PRE- CAUTION" AND "PRODUCT SAFETY NOTICE" ON PAGE 3 OF THIS MANUAL. PICTURE TUBE COMPONENTS ADJUSTMENT ADJUSTING PROCEDURE IN REPLACING CRT RGB FOCUS ADJUSTMENT 1.
Page 7
All manuals and user guides at all-guidesbox.com Note: The aim of the above-described adjustment procedure Note: Keep in mind that only the BLUE electric focus is ad- for the Green lens focus is to obtain the best lens focus justed with the black cross-hatch. after 2 - 3 hours of warming up taking into account the focus drift;...
Page 8
All manuals and user guides at all-guidesbox.com LOCATION OF SCREEN AND FOCUS VR'S To remove the Speaker grille and Front panel. FOCUS VR's SCREEN VR's Front grille REPLACEMENT OF HIGH VOLTAGE CABLE 1. When replacing Anode Lead or Anode Cap with new one, remove Lead Holder from old lead as shown in ANODE LEAD figure below, and put it on new lead.
All manuals and user guides at all-guidesbox.com WARNING : BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY PRECAU- TION" AND "PRODUCT SAFETY NOTICE" ON PAGE 3 OF THIS MANUAL. SERVICE POSITION In order to assure the performance, processed wires shall be replaced after the repair work. Work procedures are as follows: Remove the back board.
All manuals and user guides at all-guidesbox.com SERVICE MODE 1. ENTERING TO SERVICE MODE 1) Press o button once on 2) Press o button again to 3) While pressing the o button, press MENU button on TV set. Remote Control. keep pressing.
Page 11
All manuals and user guides at all-guidesbox.com 4. SELECTING THE ADJUSTING ITEMS 1) Every pressing of CHANNEL s button in the service mode changes the adjustment items in the order of table-2. (t button for reverse order) Refer to table-2 for preset data of adjustment mode. (See SETTING &...
Page 12
All manuals and user guides at all-guidesbox.com 8. SELF DIAGNOSTIC FUNCTION 1) Press “9” button on Remote Control during display of adjustment menu in the service mode. The diagnosis will begin to check if interface among IC’s are executed properly. 2) During diagnosis, the following displays are shown.
All manuals and user guides at all-guidesbox.com DESIGN MODE 1. ENTERING TO DESIGN MODE 1) Select the Service mode. 2) While pressing CALL button on Remote 3) Press MENU button on TV. and press MENU button on TV. ITEM Press DATA Press (Design mode)
All manuals and user guides at all-guidesbox.com ELECTRICAL ADJUSTMENT ITEM ADJUSTMENT PROCEDURE WIDTH 1. Call up the adjustment mode display, then select the item WID. (WID) 2. Press the VOLUME t button to get the picture so the left or right edges of raster begins to lack. 3.
Page 15
All manuals and user guides at all-guidesbox.com – 15 –...
Page 16
All manuals and user guides at all-guidesbox.com – 16 –...
Page 17
All manuals and user guides at all-guidesbox.com Viewpoint of WID (adjustment of horizontal amplitude) ..left and right flags Left side Right side Left flag end Right flag end Adjust the WID data so that the number of register flags on the left and right of Phillips pattern will come to 7 in total when added.
All manuals and user guides at all-guidesbox.com CONVERGENCE ADJUSTMENT 1. PICTURE ADJUSTMENT The adjustment can be done on 7 screens; PAL 100 Hz, PAL 1-2. Service Mode 625P, NTSC 525P, 1080i 50 Hz 4:3 or 16:9, 1080i 60 Hz 4:3 or 1-2-1.
Page 19
All manuals and user guides at all-guidesbox.com 1-2-3. Adjustment menu • Before adjusting convergence, make sure that the main adjustment has been done correctly. • To do the adjustment for each mode of NO.1, 3-8, the suitable signal and picture mode corresponding with each mode are necessary.
Page 20
All manuals and user guides at all-guidesbox.com 2. KEY FUNCTION OF REMOTE CONTROL UNIT 0 key ....Green test pattern ON/OFF b key .... Mode picture change over CALL 8 key ....Cursor down / adjusting point down 2 key ....Cursor up / adjusting point up 6 key ....
Page 21
All manuals and user guides at all-guidesbox.com 3. Picture a) 100 Hz, 625P mode (PAL) ..Correcting point: Horizontal 8 x Vertical 8 (Arrow marks denote correcting point) The first picture The second picture Data display Cursor (red) Screen center (Blinking) The first picture...
Page 22
All manuals and user guides at all-guidesbox.com b) 525P mode (NTSC) 1080i 50 Hz 4:3, 16:9, 1080i 60 Hz 4:3, 16:9 ..Correcting point: Horizontal 8 x Vertical 7 (Arrow marks denote correcting point) The second picture The first picture Data display Cursor (red)
Page 23
All manuals and user guides at all-guidesbox.com 4. ADJUSTING PICTURE DIMENSION (GREEN PICTURE) 1. 100 Hz, 625P mode (PAL) Screen center 310.5 164.5 Screen center 164.5 310.5 8.5mm 8.5mm 372.5 223.5 74.5 74.5 223.5 372.5 428.5 428.5 \ mark: center 43 inches 4:3 Screen size: Horizontal 874mm, Vertical 655mm Dimension A: 74.5mm (H span), Dimension B: 36.5mm (V span) 2.
Page 24
All manuals and user guides at all-guidesbox.com 5. Screen adjustment dimensions 5-1 PAL DFS, Progressive (4:3/Mode) Center CENTER a´ b´ c´ d´ A´ B´ C´ D´ GEOMETRY 1) VERTICAL MODEL a, a' b, b' c, c' d, d' V SPAN 43VR 55.0 164.5...
Page 25
All manuals and user guides at all-guidesbox.com 5-3 NTSC Progressive (4:3/Mode) Center CENTER a´ b´ c´ A´ B´ C´ D´ GEOMETRY 1) VERTICAL MODEL a, a' b, b' c, c' V SPAN 43VR 131.0 262.0 306.0 43.7 50VR 151.5 303.0 353.5 50.5 2) HORIZONTAL...
Page 26
All manuals and user guides at all-guidesbox.com 1080I/60, 1080I/50 PICTURE SIZE ADJUSTMENT METHOD : ONLY VS9 SERIES Signal generator: LEADER LT446 Vertical Check Point 1 Horizontal Check Point 1 Horizontal Check Point 2 Vertical Check Point 2 1080I/50Hz horizontal picture size adjustment method The 7.5th left side bar and a screen bezel are in agreement.
Page 27
All manuals and user guides at all-guidesbox.com 6. TELETEXT (P2) CIRCUIT 6-1 OUTLINE TELETEXT circuit extracts several data of input video signal, and decode them to generate display signal. It works as Stand- alone Subsystem. Major feature of TELETEXT circuit is as follows. - Digital Data Slicer of VBI (Vertical Blanking Interval) data - Display 50/60/100/120Hz mode - Display Progressive mode (Only SAA5695HL)
Page 28
All manuals and user guides at all-guidesbox.com – 28 –...
Page 29
All manuals and user guides at all-guidesbox.com 6-3 PART DESCRIPTION QT01 SAA5665HL/SAA5695HL(P2) QT01 works as Sub Micro Computer. It contains CPU(80C51), Data Capture and Display Hardware for Teletext. The block Diagram of SAA5665HL/SAA5695HL(Painter II, P2) is shown in Fig. 6-3-1. SAA5695HL will support the progressive scan mode (under development).
Page 30
All manuals and user guides at all-guidesbox.com 7. SUBDATA DESCRIPTION Sub data (Design data) of Teletext circuit is as follow. Their sub data is displayed only at Design mode. 7-1 TEXT Screen Position To adjust TEXT screen by using following subdata - TXTH = Horizontal Position Offset for Teletext screen (1/4 Character/Step) - TXTV...
Page 31
All manuals and user guides at all-guidesbox.com 8-1-2 NAVIGATION MODES To provide faster access by the user to certain pages within the Teletext service a method was included in the Teletext specification for the broadcaster to link pages, so they could be accessed using a single key press. Due to the constraints of how some equipment operated in the field one methods of linking or navigation of these pages were developed and are known as FLOF .
Page 32
All manuals and user guides at all-guidesbox.com 8-1-3 DATA TRANSMISSION FORMAT Teletext data is transmitted on VBI TV line. Subject to availability, Lines 6 to 22 and 318 to 335 may be used to carry Teletext data packets as shown in Fig. 8-1-3. Fig.
All manuals and user guides at all-guidesbox.com SCREEN AND MIRROR ALIGNMENTS ASSEMBLING AND MOUNTING OF FRONT SCREEN * Please refer to MECHANICAL DISASSEMBLY page 30. CLEANING OF LENS AND MIRROR CAUTION : Do not hold the optical system parts (lens and mirror) with bare hand to avoid finger-prints on the surface of those parts.
All manuals and user guides at all-guidesbox.com CIRCUIT CHECKS HIGH VOLTAGE CHECK CAUTION: There is no HIGH VOLTAGE ADJUSTMENT on this chassis. Checking should be done following the steps below. 1. Connect an accurate high voltage meter to the anode of the picture tube. 2.
All manuals and user guides at all-guidesbox.com CHAPTER 2 SPECIFIC INFORMATIONS SETTING & ADJUSTING DATA SAFETY INSTRUCTIONS 43" 50" HIGH VOLTAGE AT ZERO BEAM: 31.8 kV 31.8 kV MAX HIGH VOLTAGE: 32.5 kV 32.5 kV AC VOLTAGE 110~240 V 110~240 V Table-1 SERVICE MODE ADJUSTING ITEMS AND DATAS IN THE SERVICE MODE:...
All manuals and user guides at all-guidesbox.com LOCATION OF CONTROLS (Representative: 43VR9UM) Front MENU Input source selection POWER switch Remote sensor a (3) Video 3 input terminals Channel position ts Menu Volume – + Menu < > Press to draw out the control box.
Page 37
All manuals and user guides at all-guidesbox.com Remote Controller CALL i index, initial Power on/Standby CALL (For Toshiba TV/VCR/DVD only) Number buttons (0-9) 1 or 2 digit channel selection Input source selection (A 1 – A 4) Selectable picture Selectable sound...
All manuals and user guides at all-guidesbox.com PROGRAMMING CHANNEL MEMORY • First, use the ASM (Automatic Search Memory) function to preset all the active channels in your area automatically. Then, arrange the preset channels with the SEARCH, SKIP functions, MFT (Manual Fine Tuning) so that you can tune into only desired channels.
Page 39
All manuals and user guides at all-guidesbox.com To preset channels (MFT, AFT) MFT (Manual Fine Tuning) AFT (Automatic Fine Tuning) The adjustments below are not necessary under normal The AFT function automatically corrects slight fluctuations receiving conditions. However, in areas of inferior broadcast when receiving signals.
: Metal Film OMF : Oxide Metal Film : Variable Resistor : Fusible Resistor (All CD and PF capacitors are ±5%, 50V and all resistors, ±5%, 1/6W unless otherwise noted.) Models :43VR9UM, 50VR9UM Location Location Parts No. Description Parts No.
Page 42
All manuals and user guides at all-guidesbox.com Location Location Parts No. Description Parts No. Description C448 24073118 ELECTROLYTIC, 160V 33UF M C621 24797100 ELECTROLYTIC, 50V 10UF M C449 24214221 CERAMIC DISC, 500V B 220PF K C622 24591152 PLASTIC FILM, 50V 1500PF J C460 24679330 ELECTROLYTIC, 250V 33UF M 3A...
Page 43
All manuals and user guides at all-guidesbox.com Location Location Parts No. Description Parts No. Description C863 24092469 CERAMIC DISC, 2KV B 100PF K C5020 24100104 CERAMIC CHIP, 25V F 0.1UF Z C864 24766229 ELECTROLYTIC, 50V 2.2UF M C5030 24794101 ELECTROLYTIC, 16V 100UF M C865 24503041 PLASTIC FILM , 63V 0.1UF J...
Page 44
All manuals and user guides at all-guidesbox.com Location Location Parts No. Description Parts No. Description C7774 24105331 CERAMIC CHIP, 50V CH 330PF J CD05 24590102 PLASTIC FILM, 50V 1000PF J C7779 24105331 CERAMIC CHIP, 50V CH 330PF J CD06 24503045 PLASTIC FILM, 63V 0.22UF J C7780 24436471...
Page 45
All manuals and user guides at all-guidesbox.com Location Location Parts No. Description Parts No. Description CV08 24794101 ELECTROLYTIC, 16V 100UF M R315 24011681 CHIP, METAL FILM, 1/20W 680 OHM J CV09 24092621 CERAMIC CHIP, 10V B 1UF K R316 24011102 CHIP, METAL FILM, 1/20W 1K OHM J CV10 24794100...
Page 46
CHIP, METAL FILM, 1/20W 1K OHM J R442 24383680 OXIDE METAL FILM, 2W 68 OHM J R597 24011102 CHIP, METAL FILM, 1/20W 1K OHM J (43VR9UM) R601 24011152 CHIP, METAL FILM, 1/20W 1.5K OHM J R443 24988011 METAL FILM, 1/2W 1 OHM J...
Page 47
All manuals and user guides at all-guidesbox.com Location Location Parts No. Description Parts No. Description R671 24382820 OXIDE METAL FILM, 1W 82 OHM J R916 24366271 CARBON FILM, 1/6W 270 OHM J R672 24382820 OXIDE METAL FILM, 1W 82 OHM J R918 24366680 CARBON FILM, 1/6W 68 OHM J...
Page 48
All manuals and user guides at all-guidesbox.com Location Location Parts No. Description Parts No. Description R4431 24366102 CARBON FILM, 1/6W 1K OHM J R7118 24872102 CHIP, METAL FILM, 1/16W 1K OHM J R4444 24383102 OXIDE METAL FILM, 2W 1K OHM J R7119 24871100 CHIP, METAL FILM, 1/8W 10 OHM J...
All manuals and user guides at all-guidesbox.com SIGNAL BOARD PD1321 (43") SIGNAL BOARD PD1323 (50") BOTTOM (FOIL) SIDE – 59 – – 60 –...
Page 60
All manuals and user guides at all-guidesbox.com POWER BOARD PD0957 BOTTOM (FOIL) SIDE – 61 – – 62 –...
Page 61
All manuals and user guides at all-guidesbox.com DEF/CONV BOARD PD1316 (43") DEF/CONV BOARD PD1318 (50") BOTTOM (FOIL) SIDE – 63 – – 64 –...
Page 62
All manuals and user guides at all-guidesbox.com CRT-D/R BOARD PD1577-1 CRT-D/B BOARD PD1577-3 BOTTOM (FOIL) SIDE BOTTOM (FOIL) SIDE SVM-G BOARD PD1577-4 BOTTOM (FOIL) SIDE CRT-D/G BOARD PD1577-2 BOTTOM (FOIL) SIDE SVM-R BOARD PD1577-5 BOTTOM (FOIL) SIDE – 65 – –...
Page 63
All manuals and user guides at all-guidesbox.com SVM-B BOARD PD1577-6 BOTTOM (FOIL) SIDE WOW BOARD PD1319 BOTTOM (FOIL) SIDE – 67 –...
Page 64
All manuals and user guides at all-guidesbox.com FRONT BOARD PD0954-1 BOTTOM (FOIL) SIDE RMT BOARD PD0954-2 BOTTOM (FOIL) SIDE DPC BOARD PD1332-1 BOTTOM (FOIL) SIDE – 68 –...
Page 65
All manuals and user guides at all-guidesbox.com BEP BOARD PD01332-2 BOTTOM (FOIL) SIDE TEXT-P2 BOARD PD0963 BOTTOM (FOIL) SIDE – 69 –...
Page 66
All manuals and user guides at all-guidesbox.com THIS PAGE IS INTENTIONALLY LEFT BLANK. – 70 –...
All manuals and user guides at all-guidesbox.com TERMINAL VIEW OF TRANSISTORS 2SD2253 2SC3852 2SC752 2SA1788 2SC752GTM (old) 2SD1763A 2SC2482 2SA562TM 2SC5243 2SC1569 2SC2655 2SA1015 2SC4544 2SC1815 2SC4721P 2SA1788 2SC2878 2SA1306 2SC1740S 2SA1186A 2SC2120 2SA9335 RN2203 2SD1554 ON4409 RN2201 2SD2253 RN2004 2SD1556 RN1203 2SC5143...
Page 68
All manuals and user guides at all-guidesbox.com SCHEMATIC DIAGRAM MODEL : 43VR9UM / 50VR9UM WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" ON THE MANUAL FOR THIS MODEL. CAUTION: The international hazard symbols "*" in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
All manuals and user guides at all-guidesbox.com CIRCUIT BLOCK DIAGRAM AUDIO AUDIO AMP PROCESSOR SPEAKERS CLK,DATA,CS,BUSY,RST Micro Processor TUNER IF MPX with Module TEXT antenna D.CONV Front End HEADPHONE JACK Processor EEP ROM IF Module TUNER TA1318N RGB Processor VIDEO OUT TA1360AN 3D YCS TC90A65F...
Page 70
All manuals and user guides at all-guidesbox.com 43VR9UM MODEL 50VR9UM g 110 – 127, 220 – 240 V 50/60 Hz Rated voltage g 110 – 127, 220 – 240 V 50/60 Hz 260 W 260 W Power consumption 1.4 watts at standby 1.4 watts at standby...
Page 71
All manuals and user guides at all-guidesbox.com TOSHIBA CORPORATION...
Need help?
Do you have a question about the 43VR9UM and is the answer not in the manual?
Questions and answers