PCB Piezotronics ICP 356B21/ACS-23T Installation And Operating Manual page 16

4
PCB Piezotronics Inc. claims proprietary rights in
the information disclosed hereon. Neither it nor any
reproduction thereof will be disclosed to others
without the written consent of PCB Piezotronics Inc.
STANDARD STUD MOUNT
SENSOR
B
SENSOR THREAD
"A"
SENSOR
THREAD "X"
MOUNTING
"X"
THREAD
MOUNTING THREAD SEE DRAWING
5-40 A
M3 X 0.50 B
10-32 C
M5 X 0.80 D
1/4-28 E
M6 X 1.00 F
INTEGRAL STUD MOUNT
"THRU-BOLT" STUD MOUNT
"THRU-BOLT"
SENSOR
SENSOR
"X"
"X"
INTEGRAL
MOUNTING "A"
STUD
MOUNTNG THREAD SEE DRAWING
BOLT THREAD SEE DRAWING
5-40 A
10-32
A M3 X 0.50 B
M5 X 0.80
10-32 C
1/4-28
M5 X 0.80 D
M6 X 1.00
1/4-28 E
M8 X 1.25
M6 X 1.00 F
3.) FOR BEST RESULTS, PLACE A THIN LAYER OF SILICONE GREASE (OR EQUIVALENT) ON INTERFACE PRIOR
TO MOUNTING.
2 MOUNTING SURFACE SHOULD BE FLAT TO WITHIN .001(0.03) TIR OVER DIM 'A' WITH A
1 DRILL PERPENDICULAR TO MOUNTING SURFACE TO WITHIN
4
3
"A"
5-40
MOUNTING INSTRUCTIONS
(METRIC DIMENSIONS IN BRACKETS)
2
SENSOR
THREAD
MOUNTING HOLE PREPARATION:
1  .101[  2.57]
X .20[5.1]  MIN.
5-40 UNC-2B
MOUNTING
X .15[3.8]  MIN.
THREAD
4.) RECOMMENDED MOUNTING TORQUE,
4-5 INCH POUNDS
[45-55 NEWTON CENTIMETERS].
"E"
1/4-28
MOUNTING INSTRUCTIONS
(METRIC DIMENSIONS IN BRACKETS)
MOUNTING HOLE PREPARATION:
1  .218[  5.54]
"A"
X .300[7.62]  MIN.
1/4-28 UNF-2B

C X .200[5.08] MIN.
D
E 4.) RECOMMENDED MOUNTING TORQUE,
F 2-5 FOOT POUNDS
F
[3-7 NEWTON METERS].
63[1.61]
OR BETTER FINISH FOR BEST RESULTS.
 
1 .
3
"B"
M3 X 0.50
MOUNTING INSTRUCTIONS
(ENGLISH DIMENSIONS IN BRACKETS)
2
MOUNTING HOLE PREPARATION:
 2.5[  .099]
1
X 4.6 [.18]  MIN.
M3 X 0.50-6H

X 3.3[.13] MIN.
4.) RECOMMENDED MOUNTING TORQUE,
45-55 NEWTON CENTIMETERS
[4-5 INCH POUNDS].
"F"
M6 X 0.75, M6 X 1.00, M8 X 1.25
MOUNTING INSTRUCTIONS
(ENGLISH DIMENSIONS IN BRACKETS)
2
2
M6 X 1.0
MOUNTING HOLE PREPARATION:
 5.05[  .199]
1
X 8.10 [.320]  MIN.
M6X 1.0-6H

X 6.35[.250] MIN.
4.) RECOMMENDED MOUNTING TORQUE,
3-7 NEWTON METERS [2-5 FT POUNDS].
UNLESS OTHERWISE SPECIFIED TOLERANCES ARE:
DIMENSIONS IN INCHES
DECIMALS XX ±.01
XXX ±.005

ANGLES 2 DEGREES
CABLE TOLERANCES IN ENGLISH
1"≤ LENGTH < 1' = +1"/ - 0
1'≤ LENGTH < 5' = +2"/ - 0
5'≤ LENGTH < 100' = +6"/ - 0
100'≤ LENGTH = +1'/ - 0
FILLETS AND RADII
.003 - .005
2
REV
R
"C"
10-32
MOUNTING INSTRUCTIONS
(METRIC DIMENSIONS IN BRACKETS)
2
MOUNTING HOLE PREPARATION:
 
1 .159[ 4.04]
X .23[5.8]  MIN.
10-32 UNF-2B
X .15[3.8]  MIN.
4.) RECOMMENDED MOUNTING TORQUE,
4.) RECOMMENDED MOUNTING TORQUE,
10-20 INCH POUNDS
[113-225 NEWTON CENTIMETERS].
M6 X 0.75
MOUNTING HOLE PREPARATION:
 5.31[  .209]
1
X 7.62 [.300]  MIN.
M6 X 0.75-6H
X 5.08[.200]  MIN.
"P"
M8 X 1.25
MOUNTING HOLE PREPARATION:
 6.75[  .266] 1 THREAD PITCH
1
SHOWN
X 8.64 [.340]  MIN.
M8 X 1.25-6H
X 5.00[.197]  MIN.
DRAWN CHECKED
DIMENSIONS IN MILLIMETERS
[ IN BRACKETS ] NJF 05/03/23 JDM 05/03/23
DECIMALS X ± 0.3
XX ± 0.13
TITLE

ANGLES 2 DEGREES
CABLE TOLERANCES IN METRIC INSTALLATION DRAWING
2.54cm ≤ LENGTH < 30.5cm = +2.54cm/ - 0
FOR STANDARD
30.5cm ≤ LENGTH < 1.5m = +5.1cm/ - 0
1.5m ≤ LENGTH < 30.5m = +15.2cm/ - 0
081 SERIES MOUNTING
30.5m ≤ LENGTH = +30.5cm/ - 0
FILLETS AND RADII
0.07 - 0.13
2
1
REVISIONS
DESCRIPTION DIN
CHANGED "B" HOLE TOLERANCE 53828
"D"
M5 X 0.80
MOUNTING INSTRUCTIONS
(ENGLISH DIMENSIONS IN BRACKETS)
2
B
MOUNTING HOLE PREPARATION:
 4.22[  .166]
1
X 7.62 [.300]  MIN.
M5 X 0.8-6H
X 5.08[.200]  MIN.
113-225 NEWTON CENTIMETERS
[10-20 INCH POUNDS].
"G"
MOUNTING INSTRUCTIONS
FOR SPECIAL THREAD LENGTHS
2
(METRIC DIMENSIONS IN BRACKETS)
"B"
"C"
MOUNTING HOLE PREPARATION:
 DRILL DIA.
1

X "C" MIN.
TAP

X "B" MIN.
A
THREAD DEPTH : B= X + 1 THREAD PITCH
DRILL DEPTH : C= B + 3 THREAD PITCH
SEE A-F FOR APPROPRIATE DRILL AND TAP
THREAD PITCH= 1/TPI [P]
ENGINEER
MJN 05/03/23
3425 WALDEN AVE. DEPEW, NY 14043
(716) 684-0001 E-MAIL: sales@pcb.com
DWG. NO.
CODE
081-XXXX-90
IDENT. NO.
52681
SCALE: NONE SHEET 1 OF 1
1