1. Manuals
  2. Brands
  3. Scotsman Manuals
  4. Ice Maker
  5. HD356
  6. User manual

Scotsman HD356 User Manual

Scotsman hd356 ice machine: user guide
Hide thumbs
Table of Contents

Advertisement

Quick Links

Introduction

This manual includes the information needed to
uncrate, install, clean, maintain and service this ice
dispenser.
The HD356 has been designed to work with
Scotsman's CME256, CME506 or CME656. It may
also be used with a CME865 or CME1002. If using
on a prior model, such as CM250 or CME500, an
adapter kit, KBTCD200 must be ordered.

Table Of Contents

Introduction . . . . . . . . . . . . . . . . . . Page 1
Specifications . . . . . . . . . . . . . . . . . Page 2
Diagrams . . . . . . . . . . . . . . . . . . . Page 3
Uncrating . . . . . . . . . . . . . . . . . . . Page 4
Utility Connections: . . . . . . . . . . . . . . Page 6
Component Identification . . . . . . . . . . . Page 9
Service Diagnosis . . . . . . . . . . . . . . . Page 11
Adjustments . . . . . . . . . . . . . . . . . . Page 12
June 1998
Page 1
. . . Page 13
HD356

Advertisement

Table of Contents
loading

Related Manuals for Scotsman HD356

Summary of Contents for Scotsman HD356

  • Page 1: Table Of Contents

    This manual includes the information needed to uncrate, install, clean, maintain and service this ice dispenser. The HD356 has been designed to work with Scotsman’s CME256, CME506 or CME656. It may also be used with a CME865 or CME1002. If using on a prior model, such as CM250 or CME500, an adapter kit, KBTCD200 must be ordered.

  • Page 2: Specifications

    Air Temp Voltage 60 Hz Check the nameplate, located on the back of the cabinet for specific information. Scotsman reserves the right to make design changes and/or improvements at any time. Specifications and designs are subject to change without notice.

  • Page 3: Diagrams

    HD356 Diagrams June 1998 Page 3...

  • Page 4: Uncrating

    HD356 Uncrating Remove the carton from the skid. Cut the plastic straps that secure the leg kit to the skid and remove the box. Use parts of the carton as a cushion and lay the dispenser down on its back. Remove the bolts holding the skid to the machine, and separate the skid from the dispenser.

  • Page 5: Ice Machine

    There is no provision for mounting that thermostat in the standard HD356. To use a thermostat with the HD356, install kit KBTCD200 Level the wand use its thermostat Cabinet bracket. Place the ice machine on the dispenser and route the ice machine’s bin thermostat...

  • Page 6: Utility Connections

    There is a junction box on the back of the machine, connect the power supply to the wires inside the junction box. Follow all applicable codes. Be certain that the ice machine AND dispenser are grounded. Supply June 1998 Page 6...

  • Page 7: Initial Start Up & Use

    The ice machine will start and run periodically to maintain the ice in the dispenser’s hopper. Insert one U.S. quarter or a special token (available from Scotsman). The unit will fill the ice chute with ice. Push down on the chute to release the ice into a waiting container.

  • Page 8: Sanitation And Maintenance

    It is the user’s responsibility to see that the machine is properly maintained. Maintenance and Cleaning should be done a minimum of twice per year, and more if the ice machine is operating in a dusty area. Monthly: Unlock sink and remove it.

  • Page 9: Component Identification

    HD356 Component Identification View when Sink Assembly is Removed Rotor as seen from the top Rotor and Shaft Inside view of the ice chute June 1998 Page 9...

  • Page 10: Maintenance

    HD356 Maintenance Regular inspection and maintenance will provide the best assurance of trouble free operation. Begin by removing the sink assembly. Check the action of the ice chute and return springs. Clean out the lower drain pan. Pour hot water into the drain to be sure that it’s clean.

  • Page 11: Service Diagnosis

    HD356 Possible Correction Check for power, reconnect if off Push ice chute up. Check ice machine, it may be off or the dispenser’s storage capacity may have been exceeded. Move switch to ON Check - replace switch if it will not...

  • Page 12: Adjustments

    HD356 Adjustments: For Service Technicians The gear motor cam must be properly adjusted to properly position the dispensing rotor. 1. Disconnect electrical power to the dispenser. 2. Locate sink key, unlock sink and remove it from the dispenser. 3. Observe position of the rotor thru the cube chute.

  • Page 13: Removal And Replacement Procedures

    If a bin thermostat is being used, pull the thermostat capillary tube up and out of the hopper. 3. Push the ice machine back 5 ½ “ from its original position. 4. Locate nut holding rotor to shaft and remove it.

  • Page 14: Before Calling For Service

    HD356 Before Calling For Service Check these things: 1. Is the dispenser plugged in? 2. Has the dispenser’s internal switch been switched to ON? 3. Is the ice machine on? 4. Is there ice in the dispenser? 5. Is the ice chute all the way up? Record this information for future reference.

Table of Contents