Table of Contents
Advertisement
en Ventilation function "Crisp Finish"
a When the time has elapsed, a signal sounds. A noti-
fication appears on the display confirming that the
operation has finished.
Once the cooking time has elapsed:
10.
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
If you have switched off the drying function for the
11.
microwave in the basic settings and condensation
has formed in the cooking compartment, dry the
cooking compartment.
→ "Drying", Page 27
Note: If you open the appliance door during operation,
the operation stops. If you close the appliance door,
you must continue the operation. If you have changed
the basic setting for this, make sure that the microwave
does not resume operation without food inside.
→ "Basic settings", Page 21
Changing the microwave output
You can change the microwave output at any time.
Press
on the display.
1.
Press the microwave output
2.
Use the setting ring to set the microwave output.
3.
To confirm the change, press
4.
a The change is applied.
Changing the cooking time
You can change the cooking time at any time.
1.
Press
on the display.
Press the cooking time
2.
Use the setting ring to change the cooking time.
3.
4.
To confirm the change, press
a The change is applied.
11.4 Setting added microwave
Note:
Note the correct way to operate the microwave:
¡ → "Safety", Page 2
12 Ventilation function "Crisp Finish"
The ventilation function "Crisp Finish"
ture from the cooking compartment so that your food
will be more crispy.
Hot steam that may escape when the appliance door is
opened is reduced.
12.1 Suitable types of heating with the
ventilation function
Only certain types of heating are suitable for the ventil-
ation function.
You can use the ventilation function for the following
types of heating:
¡ 4D hot air
¡ Top/bottom heating
¡ Circulated air grilling
¡ Pizza setting
18
to switch the ap-
.
on the display.
.
on the display.
extracts mois-
¡ → "Preventing material damage", Page 6
¡ → "Microwave output settings", Page 11
¡ → "Cookware and accessories with microwave",
Page 16
Requirement: Observe the information about the re-
spective operating mode.
→ "Setting options with the microwave", Page 17
Press the operating mode that you require in the
1.
menu.
Select the settings for the operating mode, e.g. type
2.
of heating and temperature.
Press
"Added microwave".
3.
Use the setting ring to set the microwave output.
4.
5.
To confirm the set microwave output, press
the display.
Press
"Cooking time" and set the cooking time.
6.
7.
Press
to start the operation.
a The appliance starts to heat and the time counts
down.
a When the time has elapsed, a signal sounds. A
message appears on the display confirming that the
operation has finished.
Once the cooking time has elapsed:
8.
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
Changing added microwave
You can change or deactivate the added microwave at
any time.
Press
on the display.
1.
Press the microwave output
2.
Change or deactivate added microwave with the
3.
setting ring.
To confirm the change, press
4.
a The change is applied.
12.2 Setting the ventilation function
You can activate the ventilation function at any time,
even after the start of the operation.
Set a suitable type of heating and a temperature.
1.
If required, you can select other settings and com-
bine with the ventilation function.
Press
"Crisp Finish".
2.
a The
symbol lights up red.
Press
to start the operation.
3.
a The appliance starts heating.
a The setting values are shown on the display.
When the food is ready, use
4.
ance off.
Note: Amplified fan noises can be heard while the ap-
pliance is in operation.
Cancelling the ventilation function
You can switch off the ventilation function at any time.
Press
on the display.
1.
on
to switch the ap-
.
on the display.
to switch the appli-
Advertisement
Table of Contents
